Timeguard WPE01 IP55 Operating instructions

Brand: Timeguard

Model: WPE01 IP55

Type: Operating instructions

Timeguard WPE01 IP55 is an IP55-rated connector box enclosure designed to protect electrical connections from harsh outdoor conditions. It features two PG11 IP68 cable glands for secure cable entry, an earth terminal for earthing continuity, and ample space for accommodating terminal blocks (not included). It can be mounted horizontally or vertically on a wall or marine ply base. The enclosure allows for easy installation and maintenance of electrical connections, making it suitable for various outdoor applications, including construction sites, gardens, and industrial areas.

Timeguard WPE01 IP55 is an IP55-rated connector box enclosure designed to protect electrical connections from harsh outdoor conditions. It features two PG11 IP68 cable glands for secure cable entry, an earth terminal for earthing continuity, and ample space for accommodating terminal blocks (not included). It can be mounted horizontally or vertically on a wall or marine ply base. The enclosure allows for easy installation and maintenance of electrical connections, making it suitable for various outdoor applications, including construction sites, gardens, and industrial areas.

1. IMPORTANT. Switch off the electricity at the fuse box by removing the relevant

fuse or switching off the circuit breaker before proceeding with the installation.

WPE01 IP55 Connector Box Installation

2. Using a Philips screwdriver, separate the faceplate from the back box by

removing the four tapped screws located in each corner.

3. Using the back box as a template mark the position for the holes. Note the

back box must be mounted in the horizontal position, following the ‘TOP’

marking inside the back box. If the mounting position desired is uneven use

a sheet of marine ply as a base and fit the back box.

4. Drill the wall using a appropriate drill bit making sure not to infringe or

compromise any gas, water pipes or cables. Insert the rawl plugs into the

holes.

1

1

Deta Electrical Co Ltd, Panattoni Park, Luton Rd,

Chalton, Bedfordshire, LU4 9TT

EU - Unit 16, Ashbourne Ind. Est. Ashbourne,

Co. Meath, A84 W972 Ireland

WPE01

IP55 Connector Box Enclosure

X2 PG11 IP68 Cable Glands

23/50

Batch Code:

MOUNTING

SCREW x 2

2

5. Drill out the drain feature with a 5mm drill if required. Opening the drain hole

will reduce the IP rating of the product.

6. Secure the back box to the wall using suitable screws for the rawl plugs installed.

Ensure that the back box is correctly orientated following the ‘TOP’ marking

which is labelled inside.

7. Pass the 230V AC 50Hz supply and load cables through the cable glands, noting

the correct orientation of the supply and load positions. Use the earth terminal to

connect the incoming and outgoing earth conductors for earth continuity if

required. Note that the terminal blocks are not supplied with the enclosure

and the method of termination will be decided by the user/installer.

8. Once the mains supply is connected to the correct terminals, mount the face

plate over the back box aligning the four screws from the face plate to the four

mounting holes on the back box. Tighten until secured.

67.058.716 (Issue 1)

T.W - July 2023

Earth Terminal

1

Deta Electrical Co Ltd, Panattoni Park, Luton Rd,

Chalton, Bedfordshire, LU4 9TT

EU - Unit 16, Ashbourne Ind. Est. Ashbourne,

Co. Meath, A84 W972 Ireland

WPE01

IP55 Connector Box Enclosure

X2 PG11 IP68 Cable Glands

23/50

Batch Code:

1
2

Timeguard WPE01 IP55 Operating instructions

Brand: Timeguard

Model: WPE01 IP55

Type: Operating instructions

Timeguard WPE01 IP55 is an IP55-rated connector box enclosure designed to protect electrical connections from harsh outdoor conditions. It features two PG11 IP68 cable glands for secure cable entry, an earth terminal for earthing continuity, and ample space for accommodating terminal blocks (not included). It can be mounted horizontally or vertically on a wall or marine ply base. The enclosure allows for easy installation and maintenance of electrical connections, making it suitable for various outdoor applications, including construction sites, gardens, and industrial areas.

Download PDF

Related papers

Other documents