Kogan KAWLMFM55MA User guide

Brand: Kogan

Model: KAWLMFM55MA

Category: Flat panel wall mounts

Type: User guide

Kogan KAWLMFM55MA is a full motion TV wall mount designed for 23 to 55-inch TVs, with a maximum weight capacity of 30kg. It features a tilt function for adjusting the viewing angle and a swivel function for positioning the TV at the desired angle. The extension arms allow for flexible positioning of the TV, making it suitable for various room layouts and viewing preferences. Installation is straightforward with the included hardware and easy-to-follow instructions.

Kogan KAWLMFM55MA is a full motion TV wall mount designed for 23 to 55-inch TVs, with a maximum weight capacity of 30kg. It features a tilt function for adjusting the viewing angle and a swivel function for positioning the TV at the desired angle. The extension arms allow for flexible positioning of the TV, making it suitable for various room layouts and viewing preferences. Installation is straightforward with the included hardware and easy-to-follow instructions.

KOGAN TILT EXTENDABLE

FULL MOTION WALL MOUNT

(SUITABLE FOR 23” – 55” TVS)

KAWLMFM55MA

Read the entire instruction manual before you start installation and assembly. If you have

any questions regarding any of the instructions or warnings, contact your local distributor for

assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in

instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in

damage or serious personal injury.

• Safety gear and proper tools must be used. This product should only be installed by

professionals.

• This product is designed to be installed on solid concrete walls, masonry walls or wood

stud walls.

• Make sure that the supporting surface will safely support the combined weight of the

equipment and all attached hardware and components.

• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

• This product contains small items that could be a choking hazard if swallowed. Keep

these items away from children.

• This product is intended for indoor use only. Using this product outdoors could lead to

product failure and personal injury.

• Never exceed the maximum load capacity of 30kg or it may result in product failure or

personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist

prior to installation. If any parts are missing or faulty, contact your place of purchase for a

replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at

least every three months).

SAFETY & WARNINGS

A Bracket / wall plate

(x1)

B VESA mount extension arms

(x4)

C Extension arm bolt

(x4)

D Extension arm nut

(x4)

E Spanner

(x1)

M-A Screw

M6 x 14 (x4)

M-B Screw

M8 x 20 (x4) M-C Spacer (x4)

W-A Screw

ST6.3 x 55 (x4)

W-B Wall anchors

ø10 x 45 (x4)

W-C Washer

(x4)

Tools required for installation (not supplied)

Phillips head

screwdriver Spirit level Stud finder Pencil Drill Wrench

COMPONENTS

Step 1

Extend the bracket / wall mount (A) out to full length.

Step 2

Using a Phillips head screwdriver (not supplied), unscrew and remove the 3mm screws

attaching the arm of the mount to the bracket. Keep these screws nearby for later use.

INSTALLING MOUNT TO WALL

Step 3

Using a pencil, spirit level, mark the desired position for the mount on your wall, using the

wall mount to serve as a stencil for the hole positions. If mounting on dry wall or plaster-

board, use a stud finder first to check positions of wall studs and ensure the position is free

from electrical wiring. Using a drill, create the pilot holes.

Drywall / plaster: Use a ø4.5mm or 3/16” drill bit, drilling 55mm deep.

Masonry / concrete: Use a ø10mm or 3/8” drill bit, drilling 60mm deep.

Pencil, spirit level, stud finder and drill not supplied.

Step 4

Drywall / plaster: Position the wall mount in line with the pilot holes and secure to the wall

using washers (W-C) and ST6.3 screws (W-A). Do not use the wall anchors.

Masonry / concrete: Insert wall anchors (W-B) into the drilled holes. Position the wall mount

in line with the holes and secure to the wall using washers (W-C) and ST6.3 screws (W-A).

When using spirit level, ensure the bubble is centred as per the image

shown here.

VESA: 100x100; 100x200; 200x100; 200x200

Align the bracket with your TV’s VESA holes and secure using supplied screws (M-A or M-B,

depending on required length).

Check if spacers (M-C) are required to ensure correct length of screw, as per the below

image. Failure to follow this step may result in damage to your TV or wall mount.

INSTALLING BRACKET TO TV

VESA: 300x200; 300x300; 400x200; 400x300; 400x400

For larger VESA configurations, attach the extension arms (B) to the bracket using the bolt

and nut set (C, D), tightening with the included spanner (E).

Align the bracket with your TV’s VESA holes and secure using supplied screws (M-A or M-B,

depending on required length).

With the extension arms successfully fitted, align the bracket with your TV’s VESA holes and

secure using supplied screws (M-A or M-B, depending on required length).

Check if spacers (M-C) are required to ensure correct length of screw, as per the below

image. Failure to follow this step may result in damage to your TV or wall mount.

With the top two screws (from Step 2) loosely in place, hook the TV with bracket installed

onto the wall mount arm. Two people should carry the TV to prevent damage.

Once in place, attach the lower two screws, then tighten all four. Do not overtighten.

SECURING TV TO MOUNT

To set the TV to a vertical angle, loosen the lower two screws and move the bracket into

desired position before retightening. Do not overtighten.

Horizontal angles can be freely positioned without adjusting screws.

Add the TV’s cables to the cable management clip.

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Kogan KAWLMFM55MA User guide

Brand: Kogan

Model: KAWLMFM55MA

Category: Flat panel wall mounts

Type: User guide

Kogan KAWLMFM55MA is a full motion TV wall mount designed for 23 to 55-inch TVs, with a maximum weight capacity of 30kg. It features a tilt function for adjusting the viewing angle and a swivel function for positioning the TV at the desired angle. The extension arms allow for flexible positioning of the TV, making it suitable for various room layouts and viewing preferences. Installation is straightforward with the included hardware and easy-to-follow instructions.

Download PDF

Related papers

Other documents