NAMRON 4512735 is a Zigbee smart outlet with 4 AC outputs and 2 USB ports, allowing you to control and automate various devices and appliances in your home. It features individual control of each AC output, enabling you to switch on/off specific devices connected to it. Additionally, it supports up to 16 scenes for customized lighting and ambiance settings. The outlet also offers Touchlink commissioning for easy pairing with Zigbee remotes and supports Zigbee Green Power for binding with up to 20 compatible switches.
NAMRON 4512735 is a Zigbee smart outlet with 4 AC outputs and 2 USB ports, allowing you to control and automate various devices and appliances in your home. It features individual control of each AC output, enabling you to switch on/off specific devices connected to it. Additionally, it supports up to 16 scenes for customized lighting and ambiance settings. The outlet also offers Touchlink commissioning for easy pairing with Zigbee remotes and supports Zigbee Green Power for binding with up to 20 compatible switches.
NAMRON ZIGBEE
SKJØTELEDNING
4-veis + 2 USB
INSTRUCTION MANUAL
NAMRON ZIGBEE SKJØTELEDNING 4-veis + 2 USB 70110005
Important: Read All Instructions Prior to Installation
Produc t Data
Function introduction
Radio Frequency
Input Voltage
Device ID
Zigbee profile
Number of US B Port
Number of AC Output
US B Output Volta ge
Dimensions
AC O utput Load
US B Output Loa d
Relative humidity
Opera ting tempera ture
Max. Loa d Tota l 16A
4
AC200-240V, 50/60Hz
Max. 2.1A/output, tota l 3.1A for 2 outputs
5V DC
350×68×40(mm)
8% to 80%
0 to 40°C
Max. 16A/output, total 16A for 4 outputs
2
0x0104(ZHA)
0x000A(Plug-in Unit)
2.4GHz
Loa d sta tus indica tor, turns
off when corresponding load
is turned off, turns on when
corresponding load is turned on
2 US B ports, 1 endpoint
4 AC o utputs, 4 endpoints
• T he 4 AC outputs can be controlled individua lly
• E na bles to control ON/OFF o f the loa d, supports max. 16 scenes
• S upports find a nd bind mode to bind a Z igBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power switches
• ZigBee device that supports Touchlink commissioning
• Wa terproof grade: IP 20
• Z igBee smart outlet based on latest ZigBee 3.0 protocol
• Z igbee device with 5 endpoints, With 4 AC o utputs a nd 2 US B ports
Program button, for network
pairing, touchlink, factory reset,
short press to turn on/off loads
Zigbee indica tor, sta y off when
power on the outlet, turns on
after a dded to a Z igbee hub,
indica tes when progra m the
outlet (network pairing,
touchlink, factory reset)
3. Z igbee Network P airing through C oordinator o r Hu b ( Added to a Zigbee Network)
4. Tou c hLink to a Zigbee Remote
Zigbee
Remote
S tep 1 : Remove the device from previous zigbee network if it has a lready been a dded to, otherwise pairing will
fail. P lease refer to the pa rt " Fac tory Res et Manu ally".
S tep 2 : From your ZigBee Controller or hub interface, choose to add lighting device a nd enter P a iring mode a s
instructed by the controller.
S tep 3: Short press “Program” button 5 times continuously to set the device to network pa iring mode, LE D
indica tor will fla sh 3 times slowly then fla sh fast.
Step 1: S hort press “Prog” button 4 times (Or re- power on the device 4 times) to start Touchlink commissioning,
180S timeout. Once timeout, repeat the operation.
S tep 4: There sha ll be indication
on the remote for successful link
and LED indica tor of the outlet will
fla sh twice.
2.Th is Z igB ee d evic e i s a w ireles s r ec eiver that c ommun ic ates w ith a v ariety o f ZigB ee c ompatible
s ys tems . T his r ec eiver r ec eives a nd i s c o ntrolled by wireles s r adio s ign als f rom the c o mpatible Z igB ee
s ys tem.
1 .Plug the s mart ou tlet into AC p ower s ou rc e.
• DO NOT expose the device to moisture.
• DO NOT insta ll with power applied to device.
S afety & Warnings
Operation
S tep 4: LED indica tors will fla sh 6 times to
indica te successful pairing. LE D indica tor will
maintain the sta tus before entering into network
pa iring mode if pairing fails.
< 10cm
S tep 3: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch pa nel ma nua l to learn how.
Note: 1 ) Direc tly Tou c hLink ( both n ot added to a Z igB ee n etwork), e ac h d evic e c an l ink with 1 r emote.
2 ) Tou c hLink after b oth added to a Z igB ee n etwork, e ac h d evic e c an l ink with m ax. 3 0 remotes .
3 ) To c ontrol b y bo th g ateway and r emote, add r emote and devic e to n etwork firs t th en Tou c h Link.
4 ) After Tou c hLink, the d evic e c an b e c o ntrolled by the l inked r emotes .
S tep 2 : Bring the remote or touch pa nel within 10cm of the lighting device.
6. F ac tory R es et Manu ally
S tep 1 : Short press the “program” button 5 times continuously, the outlet will be reset to fa ctory default and enter
into network pa iring mode.
S tep 1 : Short press the progra m button 4 times to sta rt TouchLink C ommissioning, 180 seconds timeout, repea t
the operation.
7 . F ac tory R es et thro u gh a Zigbee Remote ( Touc h R es et)
Note: Ma ke sure the device a lready a dded to a n etwork, the remote a dded to the sa me one or not added to any
network.
Step 2: LE D indica tor will fla sh 3 times
slowly a nd then flahs fast and the
outlet will try to join a Z igbee network.
S tep 4: There sha ll be indication
on the remote for successful reset
and LED indica tor of the outlet will
fla sh 3 times.
5. R emoved fro m a Z igbee Network throu gh C oordinator o r Hub Interfac e
From your ZigBee controller or hub interface, choose to delete or reset the
outlet as instructed. LE D indica tor of the outlet blinks 3 times to indica te
successful reset.
Zigbee
Remote
S tep 3: Set the remote or touch panel into Touch R eset procedure to reset the
device, please refer to corresponding remote or touch pa nel ma nua l to learn how.
< 10cm
S tep 2 : Bring the remote or touch pa nel within 10cm of the outlet.
8. F ind and B ind Mode
S tep 1 : Short press “Prog.” button 3 times to sta rt Find a nd Bind mode ( LE D indica tor flashes slowly) to
find a nd bind ta rget node, 180 seconds timeout, repeat the opera tion.
9. L earning to a Z igbee G reen P ower S witc h
S tep 2 : Set the green power
switch into Lea rning mode,
please refer to its manua l.
Zigbee
Green Power
Switch
S tep 3: LED indica tor will
fla sh twice to indica te
successful learning. Then
the switch ca n control the
device.
S tep 1 : Short press “P rogram” button 4 times to start Lea rning to GP switch mode ( LED indica tor fla shes twice),
180 seconds timeout, repeat the operation.
Note: E ac h d evic e c an l earn to
max. 2 0 zigbee g reen p ower s witc h es .
1 0. D elete L earning to a Z igbee G reen P ower Switch
S tep 2 : S et the paired green power switch into
Lea rning mode, plea se refer to its ma nua l.
Zigbee
Green Power
Switch
S tep 3: LED indica tor will
fla sh 4 times to indica te
successful deleting.
S tep 1 : Short press “P rogram” button 3 times to start delete Lea rning to G P switch mode (LE D indica tor flashes
slowly), 180 seconds timeout, repeat the operation.
Note: M ake s u re bo th the d evic e and r emote are added to the s ame g ateway that s upports f ind and b ind.
Zigbee
Remote
S tep 2 : Set the remote or touch panel (ta rget node) i nto find a nd bind mode, a nd enable it
to find a nd bind initia tor, plea se refer to corresponding remote or touch pa nel manual.
S tep 3: There sha ll be indica tion on the remote or touch panel tha t it bind the device
successfully a nd ca n control it then.
Inpu t Clu s ters
• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes • 0x0006: On/off
• 0x0b05: Diagnostics
Outpu t Clu s ters
• 0x0003: Identify
1 2. Z igB ee C lu s ters t he d evic e s u pports a re as f ollows :
Note: 1 ) E ac h added d evic e c an l ink and b e c on trolled b y m ax. 3 0 added r emotes .
2 ) E ac h added remote c an l in k and c ontrol m ax. 3 0 added d evic es .
• 0x1000: ZLL Commissioning
• 0x0019: OTA
11 . S etu p a Z igbee Network & Add O ther Devic es t o the Network ( No C oordinator R equ ired)
S tep 1 : Short press “P rogram” button 4 times to ena ble the device to setup a z igbee network (LE D indicator
fla shes twice) to discover a nd add other devices, 180 seconds timeout, repeat the operation.
Zigbee
Remote
ZigB ee L ighting Devic e
< 10cm TouchLink
S tep 2 : Set another device or remote or touch pa nel into network pairing mode a nd pa ir to the network, refer to
their manuals.
S tep 3: Pa ir more devices and remotes to the network as you would like, refer to their ma nuals.
S tep 4: Bind the added devices a nd remotes through Touchlink so that the devices ca n be controlled by the
remotes, refer to their ma nua ls.
Namron AS
Nedre kalbakkvei 88B
1081 Oslo
Norway
post@namron.com
-
1
-
2
-
3
-
4
-
5
-
6
NAMRON 4512735 is a Zigbee smart outlet with 4 AC outputs and 2 USB ports, allowing you to control and automate various devices and appliances in your home. It features individual control of each AC output, enabling you to switch on/off specific devices connected to it. Additionally, it supports up to 16 scenes for customized lighting and ambiance settings. The outlet also offers Touchlink commissioning for easy pairing with Zigbee remotes and supports Zigbee Green Power for binding with up to 20 compatible switches.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: NAMRON 4512735 Manuale utente
Related papers
Other documents
-
Sunricher SR-ZG2833S User manual
-
ROBB 70110005 User manual
-
CHAINBOX SR-ZG2819S User manual
-
ROBB ROB_200-010-0 User manual
-
ROBB 16A ZigBee In Wall Switch User manual
-
ZIGBEE RGBW User manual
-
Nordtronic SR-ZG2855-5C User manual
-
ZIGBEE 100W LED User manual
-
Sunricher SR-ZG9101SAC Operating instructions
-
GLEDOPTO GL-SD-001 User manual
