Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Follow all instructions.
4. Installation should be done only by qualified personnel and conform to all local
codes.
5. Use only installation methods and materials capable of supporting four times
the maximum specified load.
Description
The SP99-321 is an adjustable pole mount for pendant domes or monitor mounts
that use 3.8 cm (1.5 inch) NPT pipe, including Spectra
®
, DF5, and DF8 Series domes
and MR Series monitor mounts. The pole mount is designed for high-ceiling
installations and can be adjusted to lengths between 1.2 to 2.4 m (4 to 8 feet). It
includes built-in safety features that prevent separation of the sleeves.
Installation
The following parts are supplied:
1 Telescoping pole mount with MRCA ceiling mount
1 Installation manual for the MRCA ceiling mount
1 Locking pin
Refer to Figure 1 while installing the pole mount.
1. Install an MRCA ceiling mount to the ceiling. Refer to the MRCA ceiling mount
installation manual for instructions. Make sure that the pole mount and ceiling
mount will support the weight of the equipment with which they are being
used.
2. Screw the threaded portion of the pole’s outer sleeve into the MRCA ceiling
mount, and tighten the set screw.
3. Loosen the locking collar on the pole, extend the pole’s inner sleeve to the
desired height, and tighten the locking collar.
4. Drill a 6.35 mm (0.25 inch) diameter hole at the locator hole just above the
locking collar. Drill all the way through both sides of the outer and inner
sleeves.
5. Insert the locking pin through the hole, and thread the locking pin screw into
the end of the pin. Tighten the locking pin screw.
6. If required, thread the mounting adapter onto the bottom of the pole’s inner
sleeve, and tighten the upper set screw. (The adapter is not required for some
monitor mounts.)
7. Pull power and video wires through the MRCA ceiling mount and pole mount.
8. Install the pendant dome or monitor mount on the pole. Follow the instructions
that are supplied with the dome or monitor mount.
9. If the mounting adapter was used, tighten the bottom set screw.
MRCA
TELESCOPING POLE
OUTER SLEEVE
TELESCOPING POLE
INNER SLEEVE
LOCKING PIN
SCREW
LOCKING PIN
MOUNTING
ADAPTER
SPECTRA
DOME (OR MONITOR
MOUNT)
HEX SET SCREW
HEX SET SCREWS
DRILL 1/4”
AT LOCATOR
HOLE
LOCKING COLLAR
Figure 1. Telescoping Pole Installation
INSTALLATION/OPERATION
SP99-321 Telescoping Pole Mount
C2207M-A (2/14)
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. © Copyright 2014, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
Pelco, Inc. 625 W. Alluvial Ave., Fresno, CA 93711 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
www.pelco.com
Specifications
Construction Aluminum
Finish Pelco light grey powder coat
Maximum Load 81.6 kg (180 lb)
Length 1.2 to 2.4 m (4 to 8 feet), adjustable
Weight 4.1 kg (9 lb)
(Design and product specifications subject to change without notice.)
Warranty Statement
For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.
SP Disclaimer
SP products carry a 90-day warranty and are not returnable. SP products do not carry any agency certifications. Pelco strongly encourages installers to
strictly follow local codes and regulations governing the installation of video security equipment and therefore assumes no liability for the installation of
products depicted herein.
REVISION HISTORY
Manual # Date Comments
C2207M 8/04 Original version.
C2207M-A 2/14 Revised the formatting, parts list, installation instructions, and specification for the Finish material.
/