VT4806 VAPORTIGHT
PAGE 2
INSTALLATION AND OPERATING INSTRUCTIONS
PAGE 3
CLIP MOUNTING
PAGE 4
HOOK MOUNTING
PAGE 5
CLEANING INSTRUCTIONS
•
Design Modification Rights Reserved
762279XXDrawing: CRev:
1 of 15Sheet:
DEFEng: 09/11/17
INSTALLATION INSTRUCTIONS
Model: VT4806
Date Drawn:
© 2018
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•
These instructions may not cover all details or variations. If additional information is needed, please contact 414.410.3600.
Model Series: Agriculture/Horticulture/Food Service
INSTALLATION AND OPERATING INSTRUCTIONS
THIS FIXTURE IS INTENDED FOR USE IN WET LOCATIONS AND IS IP66 RATED, BUT IT CAN
ALSO BE INSTALLED IN DAMP LOCATIONS.
DO NOT OPERATE IN AMBIENT TEMPERATURES EXCEEDING 120 F. HVAC EQUIPMENT MAY
BE REQUIRED TO MAINTAIN TEMPERATURES BELOW THIS VALUE.
THERE ARE NO RESTRICTIONS FOR SPACING BETWEEN LIGHTING FIXTURES OR BETWEEN A
LUMINAIRE AND PERMANENT ROOM STRUCTURE SURFACES. HOWEVER, THE FIXTURE
SHOULD NOT BE COVERED OR ENCLOSED IN ANY WAY.
THE CORD IS TO BE ROUTED SO THAT IT IS PROTECTED FROM DAMAGE AND IS NOT
SUBJECTED TO BEING UNDER STRESS. THE POWER CORD SHOULD ONLY BE USED FOR ONE
FIXTURE AND SHALL BE VISIBLE OVER ITS ENTIRE LENGTH.
DO NOT PLACE ANY PORTION OF THE CORD BEHIIND WALLS, ABOVE CEILINGS, OR
UNDERNEATH FLOORS.
DO NOT PERMANENTLY ATTACH CORD TO THE BUILDING STRUCTURE.
•
Design Modification Rights Reserved
762279XXDrawing: CRev:
2 of 15Sheet:
DEFEng: 09/11/17
INSTALLATION INSTRUCTIONS
Model: VT4806
Date Drawn:
© 2018
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•
These instructions may not cover all details or variations. If additional information is needed, please contact 414.410.3600.
Model Series: Agriculture/Horticulture/Food Service
32-36 INCHES DISTANCE
BETWEEN MOUNTING STRAPS
GENERAL PURPOSE MOUNTING STRAP
!
Design Modification Rights Reserved
•
Drawing: 762279XX Rev: C
Sheet: 3 of 15
Eng: 09/11/17
INSTALLATION INSTRUCTIONS
Model: VT4806
DEF Date Drawn:
© 2018
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•
These instructions may not cover all details or variations. If additional information is needed, please contact 414.410.3600.
Model Series: Agriculture/Horticulture/Food Service
ON FIXTURE
LIP WHERE THE CLIP
SHOULD HOOK
CLIP HOOK
Measure 32" to 36" between mounting straps on mounting surface before installation. 1.
Failure to do so could cause the fixture to become detached from the mounting
hardware.
Attach mounting straps to desired surface, T-Bar, or unistrut using hardware (by others).2.
Install fixture to mounting straps by hooking one side of the fixture housing. Make sure 3.
both hooks are clipped in before installing the other side of the clips.
Repeat step 3. Fixture should snap into place when pressure is applied. Be sure to 4.
check all (4) locations where the strap connects to the fixture. The clips should not be
sticking out.
Plug the fixture into power source.5.
1/4-20 NUT (2)
MOUNTING BRACKET (2)
SUSPENSION HOOK (2)
MOUNTING STUD
MOUNTING HOOK
•
Design Modification Rights Reserved
762279XXDrawing: CRev:
4 of 15Sheet:
DEFEng: 09/11/17
INSTALLATION INSTRUCTIONS
Model: VT4806
Date Drawn:
© 2018
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•
These instructions may not cover all details or variations. If additional information is needed, please contact 414.410.3600.
Model Series: Agriculture/Horticulture/Food Service
Secure housing bracket to fixture by placing bracket over housing studs and 1.
tighten 1/4-20 locknut.
Install hook onto each housing bracket. Verify installation and assembly 2.
integrity by pulling upwards on hook at various angles.
Suspend fixture at desired height using hardware and fasteners (by others).3.
Plug fixture into power source.4.
CLEANING AND CARE INSTRUCTIONS
Use care when cleaning this LED Luminaire. The housing is made of
reinforced polyester and the lens is made of clear or frosted Acrylc.
Do not remove lens during cleaning.
Do not use abrasive cleaners, chemicals or solvents which may result
in surface damage to lens or housing. The luminaire can be cleaned
by hose-directed water spray to remove any dust or debris. If
necessary, use mild soap with warm water for cleaning the exterior
surfaces of this fixture.
Drawing: 762279XX Rev: C
Sheet: 5 of 15
Eng: DEF Date Drawn: 09/11/17
INSTALLATION INSTRUCTIONS
Model: VT4806
Design Modification Rights Reserved
© 2018
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•
These instructions may not cover all details or variations. If additional information is needed, please contact 414.410.3600.•
Model Series: Agriculture/Horticulture/Food Service
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Philips GPL TLC 1650 DRW VSN2 1.1D Application Manual
-
Scynce LED Dragon Alpha User manual
-
HLG 100 Quantum Board LED Grow Light Veg and Bloom User manual
-
Venmar HRV 130 CFM 65 SRE User guide
-
Horticulture Lighting Group HLG 100 User manual
-
Agnetix A3 1200 User manual
-
Venmar PRO 301 User guide
-
Horticulture Lighting Group HLG 300L User manual
-
Venmar EA 1500 Owner's manual
-
Agria 6000 Owner's manual
