American Standard T480500.002 User manual
- Category
- Sanitary ware
- Type
- User manual
This manual is also suitable for
U.S. Patent No. D403,750
Certified to comply with ANSI A112.18.1
Installation
Instructions
INSTALL TRIM
1
7
5
11
3
2
4
10
9
8
6
1
T M
T480.508
T480.507
Replace the "YYY" with
appropriate finish code
022650-YYY0A
DIVERTER SPOUT (Slip-on)
T M
002
299
078016-YYY0A
ESCUTCHEON SCREWS
M907050-YYY0A
ESCUTCHEON CAP SET
023560-YYY0A
SHOWER ARM AND FLANGE
M060327-YYY0A
LEVER HANDLE KIT
M961812-YYY0A
ESCUTCHEON AND SCREWS
030126-0070A
HANDLE SCREW KIT
CHROME
CHROME/BRASS
BATH/SHOWER TRIM KIT
1/2" NPT
7" REF.
FINISHED WALL
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
4" REF.
5-1/8" REF.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78''
TOP OF TUB RIM
1/2" COPPER
1-5/8" TO 3-1/4"
4" REF.
7-5/8" REF.
ROUGHING-IN DIMENSIONS
FOR REFERENCE ONLY
Remove PLASTER GUARD (1).
Push CAP (2) on valve, place ESCUTCHEON (3) and attach with SCREWS (4).
Install HANDLE (5) by pushing it onto CARTRIDGE STEM (6) and tightening SET SCREW
(7) from below.
Install SHOWER ARM (8) with FLANGE (9). Install SHOWER HEAD (10). See Step 2.
Check proper operation of HANDLE (5) and DIVERTER SPOUT (11).
MODEL NUMBER
3
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to
adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING FORWARD AND ROTATE
COUNTER-CLOCKWISE ONE CLICK
PRY RED RING FORWARD AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN WATER IS TOO HOT
"A"
"B"
"B"
ADJUSTMENT WHEN WATER IS TOO COLD
"RED RING"- HOT LIMIT SAFETY STOP
TEMPERATURE SETTING NUMBERS
0
1
2
3
4
5
6
1
SERVICE
4
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inlets
and MANIFOLD (5).
Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).
Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force.
Clogged CARTRIDGE (4) inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off
water supply, then:
5
4
3
2
1
M 9 6 8 6 9 8
M 9 6 8 6 9 8 M 9 6 8 6 9 8 M 9 6 8 6 9 8
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE:
M953016-YYY0A
SHOWER HEAD
2
REMOVE SHOWER HEAD FROM HOUSING
1
1
2
Hold SHOWERHEAD (1) with one hand and HOUSING (2)
with the other as illustrated.
Rotate SHOWERHEAD (1) clockwise while holding HOUSING (2)
stationary. NOTE: The thread connection is a left hand
thread. Keep turning SHOWERHEAD (1) until it can be
removed from the HOUSING (2).
2a
INSTALL HOUSING
INSTALL SHOWER HEAD ASSEMBLY
2c
Slide HOUSING (2) onto
SHOWER ARM (3).
2b
INSTALL SHOWER HEAD
TEFLON TAPE
Rap SHOWER ARM (3) threads with Teflon tape.
Tighten SHOWERHEAD (1)
with an adjustable wrench.
Do not over tighten.
INSTALL HOUSING TO SHOWER HEAD
Install HOUSING (2) onto SHOWER HEAD (1). Thread
HOUSING (2) counter-clockwise to install onto SHOWER
HEAD (1). Hand tighten only.
1
3
3
2
2
BATH AND SHOWER TRIM KITS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o du c t n am e s l is t ed he r ei n a r e t ra d em a rk s o f A m er i ca n S t an d ar d I n c.
© A S A me r ic a , I nc . 2 0 07
IN MEXICO 01-800-839-12-00
T480.508
T480.507
Teflon Tape
Flat Blade Screwdriver
Plumbers' Putty or Caulking
Phillips Screwdriver
Adjustable Wrench
RECOMMENDED TOOLS
U.S. Patent No. D403,750
Certified to comply with ANSI A112.18.1
Installation
Instructions
INSTALL TRIM
1
7
5
11
3
2
4
10
9
8
6
1
T M
T480.508
T480.507
Replace the "YYY" with
appropriate finish code
022650-YYY0A
DIVERTER SPOUT (Slip-on)
T M
002
299
078016-YYY0A
ESCUTCHEON SCREWS
M907050-YYY0A
ESCUTCHEON CAP SET
023560-YYY0A
SHOWER ARM AND FLANGE
M060327-YYY0A
LEVER HANDLE KIT
M961812-YYY0A
ESCUTCHEON AND SCREWS
030126-0070A
HANDLE SCREW KIT
CHROME
CHROME/BRASS
BATH/SHOWER TRIM KIT
1/2" NPT
7" REF.
FINISHED WALL
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
4" REF.
5-1/8" REF.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78''
TOP OF TUB RIM
1/2" COPPER
1-5/8" TO 3-1/4"
4" REF.
7-5/8" REF.
ROUGHING-IN DIMENSIONS
FOR REFERENCE ONLY
Remove PLASTER GUARD (1).
Push CAP (2) on valve, place ESCUTCHEON (3) and attach with SCREWS (4).
Install HANDLE (5) by pushing it onto CARTRIDGE STEM (6) and tightening SET SCREW
(7) from below.
Install SHOWER ARM (8) with FLANGE (9). Install SHOWER HEAD (10). See Step 2.
Check proper operation of HANDLE (5) and DIVERTER SPOUT (11).
MODEL NUMBER
3
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to
adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING FORWARD AND ROTATE
COUNTER-CLOCKWISE ONE CLICK
PRY RED RING FORWARD AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN WATER IS TOO HOT
"A"
"B"
"B"
ADJUSTMENT WHEN WATER IS TOO COLD
"RED RING"- HOT LIMIT SAFETY STOP
TEMPERATURE SETTING NUMBERS
0
1
2
3
4
5
6
1
SERVICE
4
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inlets
and MANIFOLD (5).
Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).
Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force.
Clogged CARTRIDGE (4) inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off
water supply, then:
5
4
3
2
1
M 9 6 8 6 9 8
M 9 6 8 6 9 8 M 9 6 8 6 9 8 M 9 6 8 6 9 8
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE:
M953016-YYY0A
SHOWER HEAD
2
REMOVE SHOWER HEAD FROM HOUSING
1
1
2
Hold SHOWERHEAD (1) with one hand and HOUSING (2)
with the other as illustrated.
Rotate SHOWERHEAD (1) clockwise while holding HOUSING (2)
stationary. NOTE: The thread connection is a left hand
thread. Keep turning SHOWERHEAD (1) until it can be
removed from the HOUSING (2).
2a
INSTALL HOUSING
INSTALL SHOWER HEAD ASSEMBLY
2c
Slide HOUSING (2) onto
SHOWER ARM (3).
2b
INSTALL SHOWER HEAD
TEFLON TAPE
Rap SHOWER ARM (3) threads with Teflon tape.
Tighten SHOWERHEAD (1)
with an adjustable wrench.
Do not over tighten.
INSTALL HOUSING TO SHOWER HEAD
Install HOUSING (2) onto SHOWER HEAD (1). Thread
HOUSING (2) counter-clockwise to install onto SHOWER
HEAD (1). Hand tighten only.
1
3
3
2
2
BATH AND SHOWER TRIM KITS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o du c t n am e s l is t ed he r ei n a r e t ra d em a rk s o f A m er i ca n S t an d ar d I n c.
© A S A me r ic a , I nc . 2 0 07
IN MEXICO 01-800-839-12-00
T480.508
T480.507
Teflon Tape
Flat Blade Screwdriver
Plumbers' Putty or Caulking
Phillips Screwdriver
Adjustable Wrench
RECOMMENDED TOOLS
U.S. Patent No. D403,750
Certified to comply with ANSI A112.18.1
Installation
Instructions
INSTALL TRIM
1
7
5
11
3
2
4
10
9
8
6
1
T M
T480.508
T480.507
Replace the "YYY" with
appropriate finish code
022650-YYY0A
DIVERTER SPOUT (Slip-on)
T M
002
299
078016-YYY0A
ESCUTCHEON SCREWS
M907050-YYY0A
ESCUTCHEON CAP SET
023560-YYY0A
SHOWER ARM AND FLANGE
M060327-YYY0A
LEVER HANDLE KIT
M961812-YYY0A
ESCUTCHEON AND SCREWS
030126-0070A
HANDLE SCREW KIT
CHROME
CHROME/BRASS
BATH/SHOWER TRIM KIT
1/2" NPT
7" REF.
FINISHED WALL
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
4" REF.
5-1/8" REF.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78''
TOP OF TUB RIM
1/2" COPPER
1-5/8" TO 3-1/4"
4" REF.
7-5/8" REF.
ROUGHING-IN DIMENSIONS
FOR REFERENCE ONLY
Remove PLASTER GUARD (1).
Push CAP (2) on valve, place ESCUTCHEON (3) and attach with SCREWS (4).
Install HANDLE (5) by pushing it onto CARTRIDGE STEM (6) and tightening SET SCREW
(7) from below.
Install SHOWER ARM (8) with FLANGE (9). Install SHOWER HEAD (10). See Step 2.
Check proper operation of HANDLE (5) and DIVERTER SPOUT (11).
MODEL NUMBER
3
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to
adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING FORWARD AND ROTATE
COUNTER-CLOCKWISE ONE CLICK
PRY RED RING FORWARD AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN WATER IS TOO HOT
"A"
"B"
"B"
ADJUSTMENT WHEN WATER IS TOO COLD
"RED RING"- HOT LIMIT SAFETY STOP
TEMPERATURE SETTING NUMBERS
0
1
2
3
4
5
6
1
SERVICE
4
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inlets
and MANIFOLD (5).
Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).
Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force.
Clogged CARTRIDGE (4) inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off
water supply, then:
5
4
3
2
1
M 9 6 8 6 9 8
M 9 6 8 6 9 8 M 9 6 8 6 9 8 M 9 6 8 6 9 8
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE:
M953016-YYY0A
SHOWER HEAD
2
REMOVE SHOWER HEAD FROM HOUSING
1
1
2
Hold SHOWERHEAD (1) with one hand and HOUSING (2)
with the other as illustrated.
Rotate SHOWERHEAD (1) clockwise while holding HOUSING (2)
stationary. NOTE: The thread connection is a left hand
thread. Keep turning SHOWERHEAD (1) until it can be
removed from the HOUSING (2).
2a
INSTALL HOUSING
INSTALL SHOWER HEAD ASSEMBLY
2c
Slide HOUSING (2) onto
SHOWER ARM (3).
2b
INSTALL SHOWER HEAD
TEFLON TAPE
Rap SHOWER ARM (3) threads with Teflon tape.
Tighten SHOWERHEAD (1)
with an adjustable wrench.
Do not over tighten.
INSTALL HOUSING TO SHOWER HEAD
Install HOUSING (2) onto SHOWER HEAD (1). Thread
HOUSING (2) counter-clockwise to install onto SHOWER
HEAD (1). Hand tighten only.
1
3
3
2
2
BATH AND SHOWER TRIM KITS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o du c t n am e s l is t ed he r ei n a r e t ra d em a rk s o f A m er i ca n S t an d ar d I n c.
© A S A me r ic a , I nc . 2 0 07
IN MEXICO 01-800-839-12-00
T480.508
T480.507
Teflon Tape
Flat Blade Screwdriver
Plumbers' Putty or Caulking
Phillips Screwdriver
Adjustable Wrench
RECOMMENDED TOOLS
-
1
-
2
-
3
American Standard T480500.002 User manual
- Category
- Sanitary ware
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard FloWise Showerhead 1660.715 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Speakman SM-5490-ADA Installation guide
-
-
-
-
-
-
-
-
Delta Faucet T17282-SS Installation guide
-
Delta T17494-CZ-I Installation guide