Audioplex BALANCED AUDIO CONTROLLER Installation guide

Type
Installation guide
TECHNOLOGY
TM
BALANCED AUDIO CONTROLLER INSTALLATION MANUAL
SPECIFICATIONS
USES
Front Panel ON/OFF Switch with LED power indicator.
Two mono inputs (A&B) and eight mono outputs (1-8), may be configured as one stereo in, four stereo out.
1/4" stereo phone jacks in and out; these accommodate balanced and unbalanced signals.
Channel A or Channel B may be directed to each output via the front panel switches.
Eight independent outputs with individual gain controls.
16 VAC UL rated Power Supply included.
One rack height- 17"W x 1.75"H x 4.5"D.
The BAC is used as a stereo line level source distributor to four different locations in stereo or as a mono line level source
distributor to eight different locations in mono. Some common examples of this would be to;
1. Split and buffer the output of a CD player to four different Receiver/Amplifiers.
2. Distribute line level signals long distances throughout a house or building. Doing this in balanced mode is the preferred method
for noise rejection.
3. Send a source balanced or unbalanced out to four locations with a mixture of input types; i.e. two amplifiers with XLR
balanced inputs and two amplifiers with RCA unbalanced inputs.
Please see diagrams on following pages for reference
The BAC is a line level audio distribution controller. The input consists of A and B channels. Though each channel is mono in
nature, a stereo signal may be accommodated using both inputs. Each input may be configured as balanced or unbalanced at the flick of a
switch (rear panel). Therefore both inputs may be balanced, unbalanced, or split with one balanced and the other unbalanced.
There are eight output channels. For each of these outputs there is a gain control knob and input channel selector (A or B) on the
front panel. Each output may also be configured as balanced or unbalanced at the flick of a switch (rear panel).
When connecting different pieces of equipment, ground loops are always a possibility. This is particularly true when these pieces
of equipment are in different parts of a building or a house. The ground loop usually manifests itself as audio noise/hum or video picture
interference. The best way to locate the problem is to disconnect items one at a time until the problem goes away. In some instances the
difference in ground potentials is enough to lead to a shock. Care should be taken when dealing with one. To minimize the possibility of a
ground loop wire shields should be left disconnected at one end, however a ground wire must be connected between the equipment by a
single wire, the bigger the better. Leave all the shields disconnected at the BAC or at the sources and destinations. This pertains only to
signal cables. DO NOT LIFT THE BUILDING GROUND ON ANY PIECE OF EQUIPMENT SUPPLIED WITH ONE! DO NOT CUT
THE GROUND SPADE OFF OF THE ELECTRICAL CORD!...........You risk your own life and the lives of others.
On the following pages wiring diagrams for different types of connectors are provided. Notice the shields are left disconnected at
one end of the wire as stated above. In some cases, Baluns (balanced to unbalanced transformers) are required. Certain types of
connectors/adaptors may also be needed. Audioplex Technology(tm) sells many of these items should you need them.
CD PLAYER
MIXER
L R
L R
B A
B A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
L R
L R
L R
L R
L R
L R
L R
L R
16 VAC POWER SUPPLY
16 VAC POWER SUPPLY
BAC
BAC
AMPLIFIER 4
AMPLIFIER 4
AMPLIFIER 3
AMPLIFIER 3
AMPLIFIER 2
AMPLIFIER 2
AMPLIFIER 1
AMPLIFIER 1
BAC used to split and buffer the output of a CD player
to four different Receiver/Amplifiers.
BAC used to send a source, balanced or unbalanced out to four
locations with a mixture of input types; i.e. two amplifiers with XLR
balanced inputs and two amplifiers with RCA unbalanced inputs.
UNBALANCED
BALANCED
BALANCEDBALANCEDUNBALANCEDUNBALANCED
UNBALANCEDUNBALANCEDUNBALANCEDUNBALANCED
Professional Amp
w/ balanced input.
XLR or 1/4" stereo
Professional Amp
w/ balanced input.
XLR or 1/4" stereo
Consumer Receiver
w/ unbalanced input
RCA inputs
Consumer Receiver
w/ unbalanced input
RCA inputs
CD PLAYER
L R
B A
12345678
L R L R L R L R
16 VAC POWER SUPPLY
BAC
AMPLIFIER 4 AMPLIFIER 3 AMPLIFIER 2 AMPLIFIER 1
BAC used to distribute line level signals long distances
throughout a house or building. Doing this in balanced
mode is the preferred method for noise rejection.
UNBALANCED
BALANCED
BALUNBALUNBALUNBALUN
BALANCEDBALANCEDBALANCED
BEDROOM 1BEDROOM 2
DEN
FAMILY ROOM
WARRANTY
Your AUDIOPLEX TECHNOLOGY(tm) BALANCED AUDIO CONTROLLER is covered by a 10 year warranty against
any defects in workmanship and materials. Any defects will be remedied without charge for labor or parts during this period
of time following the date of purchase.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this warranty.
AUDIOPLEX TECHNOLOGY(tm) is not responsible for defective operation caused by abuse or by modification or service by
any unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any necessary
servicing must be done by AUDIOPLEX TECHNOLOGY(tm). The product must be returned expenses prepaid, with written
authorization from the company. The product must be shipped with proof of purchase and in the original carton and packing
material to avoid damage.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.
Suggested Wire Connections from BAC Output to Amp/Receiver/Processor
1/4" Mono to RCA
NO
CONNECT
BAC OUTPUT
AMP/REC
1/4" Stereo to RCA
NO
CONNECT
RED
BLACK
SHIELD
NO
CONNECT
NO
CONNECT
NO
CONNECT
NO
CONNECT
RED
RED
RED
RED
BLACK
BLACK
BLACK
BLACK
SHIELD
SHIELD
SHIELD
SHIELD
RED
BLACK
SHIELD
1/4" Stereo to 1/4" Mono
1/4" Mono to 1/4" Mono
1/4" Mono to 1/4" Stereo
1/4" Mono to XLR
NO
CONNECT
RED
BLACK
SHIELD
1/4" Stereo to 1/4" Stereo
NO
CONNECT
RED
BLACK
SHIELD
1/4" Stereo to 1/4" Stereo
3
1
2
NO
CONNECT
RED
BLACK
SHIELD
1/4" Stereo to XLR
3
1
2
NO
CONNECT
RED
BLACK
SHIELD
1/4" Stereo to XLR
3
1
2
Switch Position UNBALANCED
Switch Position BALANCED
Suggested Wire Connections from SOURCE to BAC
RCA to 1/4" Mono
SOURCE
BAC IN A or B
RCA to 1/4" Stereo
NO
CONNECT
RED
BLACK
SHIELD
NO
CONNECT
NO
CONNECT
NO
CONNECT
NO
CONNECT
RED
RED
RED
RED
BLACK
BLACK
BLACK
BLACK
SHIELD
SHIELD
SHIELD
SHIELD
NO
CONNECT
RED
BLACK
SHIELD
1/4" Mono to 1/4" Stereo
1/4" Mono to 1/4" Mono
1/4" Mono to 1/4" Stereo
XLR to 1/4" Mono
NO
CONNECT
RED
BLACK
SHIELD
1/4" Stereo to 1/4" Stereo
NO
CONNECT
RED
BLACK
SHIELD
1/4" Stereo to 1/4" Stereo
3
2
1
NO
CONNECT
RED
BLACK
SHIELD
XLR to 1/4" Stereo
3
2
1
NO
CONNECT
RED
BLACK
SHIELD
XLR to 1/4" Stereo
3
2
1
Switch Position UNBALANCED
Switch Position BALANCED
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Audioplex BALANCED AUDIO CONTROLLER Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI