Allied Telesis GS950/48 Installation guide

613-001768 Rev E

AT-GS950/48PS

AT-GS950/28PS

AT-GS950/16PS

AT-GS950/10PS

Gigabit Ethernet PoE+ Switches

Installation Guide

Copyright  2016 Allied Telesis, Inc.

Inc.

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names,

company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective

owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document

without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied

Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited

to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has

been advised of, known, or should have known, the possibility of such damages.

3

Electrical Safety and Emissions

Standards

This section contains the following:

 “US Federal Communications Commission”

 “Industry Canada”

 “Emissions, Immunity and Electrical Safety Standards” on page 4

 “Translated Safety Statements” on page 4

US Federal Communications Commission

Radiated Energy

Note

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with this instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

Note

Modifications or changes not expressly approved of by the manufacturer or the FCC, can void

your right to operate this equipment.

Industry Canada

Radiated Energy

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

4

Emissions, Immunity and Electrical Safety Standards

RFI Emissions FCC Class A, EN55022 Class A, CISPR 22 Class A, VCCI Class A, C-TICK, CE

Warning

In a domestic environment this product may cause radio interference in which case the user

may be required to take adequate measures.  E84

EMC (Immunity) EN55024, EN61000-3-2, EN61000-3-3

Electrical Safety EN60950-1 (TUV), UL 60950-1 (

C

UL

US

)

Warning

Laser Safety: EN60825  L7

Translated Safety Statements

Important: The  indicates that a translation of the safety statement is available in a PDF

document titled Translated Safety Statements on the Allied Telesis website at

www.alliedtelesis.com/support.

5

Contents

Preface............................................................................................................................................................. 11

Symbol Conventions.................................................................................................................................. 12

Contacting Allied Telesis............................................................................................................................ 13

Chapter 1: Overview ..................................................................................................................................... 15

Features..................................................................................................................................................... 16

Front and Back Panels............................................................................................................................... 18

Management Software............................................................................................................................... 21

Twisted Pair Ports...................................................................................................................................... 22

Power over Ethernet (PoE)........................................................................................................................ 23

Combo Ports.............................................................................................................................................. 24

LEDs .......................................................................................................................................................... 26

eco-Friendly Button.................................................................................................................................... 36

Power Supply............................................................................................................................................. 38

Fans........................................................................................................................................................... 39

Chapter 2: Installation ................................................................................................................................... 41

Reviewing Safety Precautions ................................................................................................................... 42

Selecting a Site for the Switch ................................................................................................................... 46

Cable Specifications................................................................................................................................... 47

Unpacking the Switch................................................................................................................................. 48

Installing the Switch on a Desktop............................................................................................................. 50

Installing the Switch in an Equipment Rack............................................................................................... 51

Installing the Switch on a Wall ................................................................................................................... 53

Installing Optional SFP Transceivers......................................................................................................... 56

Cabling the Switch ..................................................................................................................................... 59

Powering On the Switch............................................................................................................................. 60

Managing the Switch.................................................................................................................................. 64

Chapter 3: Troubleshooting .......................................................................................................................... 65

Appendix A: Technical Specifications ............................................................................................................ 69

Physical Specifications............................................................................................................................... 69

Environmental Specifications..................................................................................................................... 70

Power Specifications.................................................................................................................................. 70

PoE Specifications..................................................................................................................................... 70

Safety and Electromagnetic Emissions Certifications................................................................................ 71

Connectors and Port Pinouts..................................................................................................................... 71

Contents

6

7

Figures

Figure 1: AT-GS950/10PS and AT-GS950/16PS Front Panels........................................................................................... 18

Figure 2: AT-GS950/28PS and AT-GS950/48PS Front Panels........................................................................................... 19

Figure 3: AT-GS950/10PS Back Panel................................................................................................................................ 20

Figure 4: AT-GS950/16PS and AT-GS950/28PS Back Panels........................................................................................... 20

Figure 5: AT-GS950/48PS Back Panel................................................................................................................................ 20

Figure 6: PWR LED on AT-GS950/10PS............................................................................................................................ 26

Figure 7: SYSTEM LED on AT-GS950/16PS...................................................................................................................... 27

Figure 8: SYS LED on AT-GS950/28PS.............................................................................................................................. 27

Figure 9: SYS LED on AT-GS950/48PS.............................................................................................................................. 27

Figure 10: AT-GS950/10PS Link/Activity and Speed LEDs................................................................................................. 28

Figure 11: AT-GS950/16PS Link/Activity/Speed LEDs........................................................................................................ 29

Figure 12: AT-GS950/28PS Link/Activity/Speed LEDs........................................................................................................ 29

Figure 13: AT-GS950/48PS Link/Activity/Speed Port LEDs................................................................................................ 30

Figure 14: AT-GS950/10PS SFP Status LEDs.................................................................................................................... 31

Figure 15: AT-GS950/16PS SFP Status LEDs.................................................................................................................... 31

Figure 16: AT-GS950/28PS SFP Status LEDs.................................................................................................................... 31

Figure 17: AT-GS950/48PS SFP Status LEDs.................................................................................................................... 32

Figure 18: AT-GS950/10PS PoE and PoE MAX LEDs........................................................................................................ 34

Figure 19: AT-GS950/16PS PoE and PoE MAX LEDs........................................................................................................ 34

Fi

gure 20: AT-GS950/28PS PoE and PoE MAX LEDs........................................................................................................ 34

Figure 21: AT-GS950/48PS PoE and PoE MAX LEDs........................................................................................................ 34

Figure 22: eco-Friendly Button............................................................................................................................................ 36

Figure 23: AT-GS950/28PS Unit Orientation....................................................................................................................... 45

Figure 24: Shipping Package Contents............................................................................................................................... 49

Figure 25: Attaching the Rubber Feet ................................................................................................................................. 50

Figure 26: Attaching the Rack-Mount Brackets to the Switch.............................................................................................. 51

Figure 27: Attaching the Rack-Mount Brackets to the Switch (Continued).......................................................................... 52

Figure 28: Mounting the Switch in an Equipment Rack....................................................................................................... 52

Figure 29: Attaching the Brackets to Install the Switch on a Wall........................................................................................ 53

Figure 30: Marking the Screw Hole Locations..................................................................................................................... 54

Figure 31: Securing the Switch to the Wall.......................................................................................................................... 55

Figure 32: Inserting the SFP................................................................................................................................................ 57

Figure 33: Positioning the SFP Handle in the Upright Position ........................................................................................... 57

Figure 34: Installing the Retaining Clip................................................................................................................................ 60

Figure 35: Raising the Retaining Clip.................................................................................................................................. 61

Figure 36: Plugging in the AC Power Cord.......................................................................................................................... 61

Figure 37: Lowering the Retaining Clip................................................................................................................................ 62

Figure 38: Plugging in the AC Power Cord.......................................................................................................................... 63

Figure 39: RJ-45 Connector and Port Pin Layout................................................................................................................ 71

List of Figures

8

9

Tables

Table 1. Combo Ports .........................................................................................................................................................24

Table 2. AT-GS950/10PS PWR LED Functional Descriptions ...........................................................................................26

Table 3. AT-GS950/16PS, AT-GS950/28PS, and AT-GS950/48PS SYS LED Functional Descriptions ............................28

Table 4. AT-GS950/10PS L/A and SPD LEDs Functional Descriptions .............................................................................29

Table 5. AT-GS950/16PS, AT-GS950/28PS, and AT-GS950/48PS L/A LED Functional Descriptions ..............................30

Table 6. SFP Slot LED Functional Descriptions - AT-GS950/10PS, AT-GS950/16PS, AT-GS950/48PS ..........................32

Table 7. SFP Slot LED Functional Descriptions - AT-GS950/28PS ...................................................................................33

Table 8. PoE Status LED Functional Descriptions .............................................................................................................35

Table 9. Twisted Pair Cabling and Distances .....................................................................................................................47

Table 10. Chassis Dimensions ...........................................................................................................................................69

Table 11. Chassis Weight ...................................................................................................................................................69

Table 12. Environmental Specifications ..............................................................................................................................70

Table 13. Max AC Input Power Specifications ....................................................................................................................70

Table 14. Max Ports Supported per PoE Class ..................................................................................................................71

Table 15. Safety and Electromagnetic Emissions Certifications .........................................................................................71

Table 16. MDI Pin Signals (10Base-T or 100Base-TX) ......................................................................................................72

Table 17. MDI-X Pin Signals (10Base-T or 100Base-TX) ..................................................................................................72

Table 18. RJ-45 1000Base-T Connector Pinouts ...............................................................................................................72

List of Tables

10

11

Preface

This guide contains the installation instructions for the AT-GS950/10PS,

AT-GS950/16PS, AT-GS950/28PS, and AT-GS950/48PS Gigabit Ethernet

PoE+ Switches. This preface contains the following sections:

 “Symbol Conventions” on page 12

 “Contacting Allied Telesis” on page 13

The AT-GS950/10PS, AT-GS950/16PS, AT-GS950/28PS, and AT-GS950/

48PS switches may be collectively referred to as GS950/PS Series

switches in this guide.

12

Symbol Conventions

This document uses the following conventions:

Note

Notes provide additional information.

Caution

Cautions inform you that performing or omitting a specific action

may result in equipment damage or loss of data.

Warning

Warnings inform you that performing or omitting a specific action

may result in bodily injury.

Warning

Warnings inform you that an eye and skin hazard exists due to the

presence of a Class 1 laser device.

Note

The  indicates that a translation of the safety statement is

available in a PDF document titled “Translated Safety Statements”

on the Allied Telesis website at http://www.alliedtelesis.com/

support.

GS950/PS Series Switches Installation Guide

13

Contacting Allied Telesis

If you need assistance with this product, you may contact Allied Telesis

technical support by going to the Support & Services section of the Allied

Telesis web site at www.alliedtelesis.com/support. You can find links for

the following services on this page:

 24/7 Online Support - Enter our interactive support center to

search for answers to your questions in our knowledge database,

check support tickets, learn about RMAs, and contact Allied

Telesis technical experts.

 USA and EMEA phone support - Select the phone number that

best fits your location and customer type.

 Hardware warranty information - Learn about Allied Telesis

warranties and register your product online.

 Replacement Services - Submit a Return Merchandise

Authorization (RMA) request via our interactive support center.

 Documentation - View the most recent installation guides, user

guides, software release notes, white papers and data sheets for

your product.

 Software Updates - Download the latest software releases for your

product.

For sales or corporate contact information, go to www.alliedtelesis.com/

purchase and select your region.

14

15

Chapter 1

Overview

This chapter provides descriptions of the AT-GS950/10PS, AT-GS950/

16PS, AT-GS950/28PS, and AT-GS950/48PS Layer 2 Gigabit Ethernet

PoE+ Switches and contains the following sections:

 “Features” on page 16

 “Front and Back Panels” on page 18

 “Management Software” on page 21

 “Twisted Pair Ports” on page 22

 “Power over Ethernet (PoE)” on page 23

 “Combo Ports” on page 24

 “LEDs” on page 26

 “eco-Friendly Button” on page 36

 “Power Supply” on page 38

 “Fans” on page 39

Chapter 1: Overview

16

Features

Here are the hardware features of the GS950/PS Series switches.

Twisted Pair

Ports

Here are the basic features of the 10/100/1000 Mbps twisted-pair ports:

 10, 16, 24, or 48 ports per switch

 8, 16, or 24 Power over Ethernet (PoE) ports per switch

 10Base-TX, 100Base-T and 1000Base-T compliant

 IEEE 802.3u Auto-Negotiation compliant

 Auto-MDI/MDIX

 100 meters (328 feet) maximum operating distance

 IEEE 802.3x Flow Control in 10/100Base-TX full-duplex operation

 IEEE 802.3x Back Pressure in 10/100Base-TX half-duplex

operation

 IEEE803.3z 1000Base-T Flow Control

 Support for Jumbo frames up to 10KB

 RJ-45 connectors

SFP Slots The AT-GS950/10PS, AT-GS950/16PS, and AT-GS950/48PS switches

support both 100Base-FX and 1000Base-SX/LX transceivers. The

AT-GS950/28PS switch supports 1000Base-SX/LX transceivers. The

switches support either two or four slots for SFPs:

 Two SFP slots on the AT-GS950/10PS and AT-GS950/16PS

switches

 Four SFP slots on the AT-GS950/28PS and AT-GS950/48PS

switches

Note

On the AT-GS950/10PS, AT-GS950/16PS, and AT-GS950/48PS

switches, the SFP slots are paired with twisted pair ports on the

switch to form combo ports. For more information, see “Combo

Ports” on page 24.

Note

You must purchase SFP transceivers separately. For a list of

supported transceivers, contact your Allied Telesis distributor or

reseller.

GS950/PS Series Switches Installation Guide

17

Note

See the product data sheets for the specific Allied Telesis SFP

modules supported by the GS950/PS Series switches.

LEDs Here is a brief description of the port LEDs:

 Power LED/SYS; refer to “PWR/SYS LEDs” on page 26.

 Speed and link/activity LEDs for the twisted pair ports; refer to “10/

100/1000 BaseT Link Activity LEDs” on page 28.

 Link/activity LEDs for the SFP slots; refer to “SFP LEDs” on

page 31.

 eco-Friendly button turns off the LEDs to conserve electricity; refer

to “PoE LEDs” on page 33.

Installation

Options

The GS950/PS Series switches can be installed in the following ways:

 Rack mounted in a 19-inch equipment rack

 Mounted on a desk or tabletop

 Wall mounted for the AT-GS950/10PS, AT-GS950/16PS, and

AT-GS950/28PS only

Power

Conservation

The GS950/PS Series switches have the following power conservation

features:

 eco-Friendly button to turn off the port LEDs when the system is

not being monitored

 High-efficiency power supply

 Power scaling based on traffic loads on ports operating at 1000

Mbps (port power scaling not available at 10 or 100 Mbps)

 Power shutdown on unused ports

MAC Address

Table

Here are the basic features of the MAC address table:

 Storage capacity up to 16KB MAC address entries

 Automatic learning and aging

Chapter 1: Overview

18

Front and Back Panels

Figure 1 illustrates the front panels of the AT-GS950/10PS and

AT-GS950/16PS Gigabit Ethernet Switches.

Figure 1. AT-GS950/10PS and AT-GS950/16PS Front Panels

Figure 2 on page 19 illustrates the front panels of the AT-GS950/28PS

and AT-GS950/48PS Gigabit Ethernet Switches.

AT-GS950/16

AT-GS950/16PS

10/100/1000Base-T

SFP Slots

Twisted Pair Ports

AT-GS950/10PS

eco-Friendly

Button

Port and

System LEDs

eco-Friendly

Button

SFP Slots

Port and

System LEDs

eco-Friendly

Button

10/100/1000Base-T

Twisted Pair Ports

GS950/PS Series Switches Installation Guide

19

Figure 2. AT-GS950/28PS and AT-GS950/48PS Front Panels

AT-GS950/48PS

SFP Slots

System LEDs

eco-Friendly

Button

10/100/1000Base-T

Twisted Pair Ports

AT-GS950/28PS

SFP Slots

eco-Friendly

Button

10/100/1000Base-T

Twisted Pair Ports

Port and

System LEDs

Chapter 1: Overview

20

See Figure 3 for an example of the AT-GS950/10PS back panel.

Figure 3. AT-GS950/10PS Back Panel

See Figure 4 for an example of the AT-GS950/16PS and AT-GS950/28PS

back panels.

Figure 4. AT-GS950/16PS and AT-GS950/28PS Back Panels

See Figure 5 for an example of the AT-GS950/48PS back panel.

Figure 5. AT-GS950/48PS Back Panel

AC Input

Page is loading ...

Allied Telesis GS950/48 Installation guide

This manual is also suitable for

Allied Telesis GS950/48 Installation guide

Related papers

Other documents