2. Montigo
  3. H-Series Surround

Montigo H-Series Surround Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Montigo H-Series Surround Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
XG0903 - 150204.2
Installing the H34/H38/H42 Surround
for use with:
H-Series; H34-DF
H-Series; H38-DF
H-Series; H42-DF
®
C US
Tools Required
1) Power Drill, (eight 1/8" holes)
2) #8 Hexhead Driver, (to match hardware)
3) Carpenters level (Final Step, if required)
Installing the Surround
To install the Montigo Stainless steel or Black contemporary
surround to the H34DF, H38DF, or H42DF follow these steps.
Note: Four sided surround requires a raised installation.
Do not install nailing ange when installing four sided
surround. Refer to the installation and maintenance
manual for your replace for further information and
framing dimensions.
Step 1. Mark the location of the holes needed.
From the package of hardware locate one of the Attachment
Brackets. Hold this part in place as shown in Figure 2. With a
pencil or pen mark the (6) six holes on the face of the replace
frame, (see Figure 2.) Note: Ensure the brackets align with
Figure 2. Below.
Figure 2. Bracket Alignment
M
N
P
1”
O
Surround Dimensions
M N O P
H34DF 31 7/16" 24 1/4" 45 15/16" 38 7/8"
H38DF 35 3/16" 26 3/8" 49 11/16" 41"
H42DF 39 5/8" 30 7/16" 54 1/8" 45 1/16"
Figure 1. Surround Dimensions (tolerance within 1/16")
A
REVISIONS
REV.
DESCRIPTION
DATE
CHANGED BY
-
.
- -
1:2
DWG. NO.
SHEET 1 OF 1
WEIGHT:
P38-MAN3
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
P38
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\CADD\38\P38\P38
December-03-15 9:26:13 AM
SCALE
PC
Description
FACEPLATE BRACKET
MANUAL
A
Revision
04/01/2015
1
3
2
4
B
C
ALIGN (2) ATTACHMENT BRACKETS
ON CENTER OF FRAME VERTICALS
(LEFT AND RIGHT SIDE TYPICAL
MOUNTING HOLES (3) PER SIDE
(LEFT AND RIGHT SIDE TYPICAL)
BRACKET TO BE
FLUSH WITH
OUTSIDE EDGE
OF FIREPLACE
(TYPICAL)
MOVING BRACKETS (2)
(LEFT AND RIGHT SIDE
TYPICAL)
BRACKETS TO
BE FLUSH WITH
TOP OF FIREPLACE
FRAME (TYPICAL)
REVISIONS
REV.
DESCRIPTION
DATE
CHANGED BY
-
.
- -
1:2
DWG. NO.
SHEET 1 OF 1
WEIGHT:
P38-MAN4
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
P38
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\CADD\38\P38\P38
December-03-15 9:28:51 AM
SCALE
PC
Description
FACEPLATE BRACKET
ALIGNMENT MANUAL
A
Revision
12/03/2015
Parts Included
1) 1-Pc, Surround
2) 2-Pcs, Attachment Brackets
3) 4-Pcs, Moving Brackets
4) 1-Pkg. Hardware
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING
XG0903 - 150204.2
f i r e f e a t u r e
Step 2. Drill holes.
Before you go any farther now is the time to double
check the location of the holes, do they agree with Fig-
ure 2. If you are satised with the location of the holes, use a
punch to mark the holes, then using a 1/8" drill, drill out the six
holes.
Step 3. Install the (2) two Attachment Brackets. (See
Figure 2)
Install the two (2) Attachment Brackets you used as a guide.
Have someone hold one of the Brackets in place, using the Hex-
tool, place a self-tapping #8-18 sheet metal hex screw into the
hole and twist it into the hole half way.
Follow this procedure for the remaining two (2) screws in the
rst bracket. After the three (3) screws are in place tighten them
in place. Repeat the procedure in Step 3 for the second Attach-
ment Bracket.
Step 4. Install the (2) two Movable Brackets. (If installed
disregard this step. If not See Figure 3)
Install the two (2) Movable Brackets. (These move up or
down to level and align the surround. This will produce a
symmetrical reveal when correctly adjusted).
Figure 3. Installing the Movable Brackets
Pick up one of the brackets, using the supplied hardware, mount
it into place. Slide the bolt through the bracket 'front to back',
(See Figure 3), then tighten the bolt using a open end wrench or
socket.
Follow this procedure for the remaining bolt in the second Mov-
able Bracket.
Step 5. Installing the Lower Moveable Brackets
Using the self drilling screws supplied secure the moveable
brackets to the front of the replaces lower facia. The cut out on
the moveable braket should be such that the cut out is facing
up. The moveable bracket should be level with the top of the
replace lower facia and spaced evenly from left to right as to
support the weight of the surround. See gure 4 and 5.
A
A
A
SECTION
A-A
FLUSH WITH
VALVE/BOTTOM
PANEL
REVISIONS
REV.
DESCRIPTION
DATE
CHANGED BY
-
.
- -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
P38-MAN2
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
P38
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\CADD\38\P38\P38
March-31-15 12:54:25 PM
SCALE
PC
Description
FACEPLATE MANUAL
A
Revision
03/31/2015
A
A
A
SECTION
A-A
FLUSH WITH
VALVE/BOTTOM
PANEL
REVISIONS
REV.
DESCRIPTION
DATE
CHANGED BY
-
.
- -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
P38-MAN2
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
P38
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\CADD\38\P38\P38
March-31-15 12:54:25 PM
SCALE
PC
Description
FACEPLATE MANUAL
A
Revision
03/31/2015
Figure 4. Installing the Movable Brackets on Lower Facia
Figure 5. Installing the Movable Brackets on Lower Facia
Cut Out
Lower Facia
Moveable Bracket
Moveable Bracket
Lower Facia
A
REVISIONS
REV.
DESCRIPTION
DATE
CHANGED BY
-
.
- -
1:2
DWG. NO.
SHEET 1 OF 1
WEIGHT:
P38-MAN3
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
P38
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\CADD\38\P38\P38
December-03-15 9:26:13 AM
SCALE
PC
Description
FACEPLATE BRACKET
MANUAL
A
Revision
04/01/2015
10-24 Machine Screw
Moveable Bracket
Cut out
XG0903 - 150204.2
f i r e f e a t u r e
Step 6. Placing the Surround
Finally it's time to install the Stainless steel or Black Sur-
round. For this step it would be helpful to have someone
help you hold the surround in place.
Lift the surround over the four (4) Movable Brackets and slide
the surround downward. The surround should securely lock
in place in the cut out in the lower moveable brackets. Cent-
er the surround left to right.If the surround doesn't clear
the top or bottom of the replace you will have to adjust the
movable brackets up or down. Remove the surround place it
aside. Adjust the bracket as required. Repeat as necessary.
Step 7. Final adjusting of the Surround
This step is not necessary if the surround ts tightly around
the replace, or the adjustment is acceptable. But, if your
surround has an uneven reveal, or unequal gap around/be-
tween the replace and surround, using a carpenters level
adjust the Movable brackets as needed.
Finally place the adjusted Surround back on the Brackets and
admire your Contemporary Montigo replace.
WARNING
When installing the replace - gas lines, ttings, accesso-
ries or any other objects cannot impede the proper
movement of the door buckles.
WARNING
Screen Barrier must still be used with the Surround.
The screen should only ever be removed for servic-
ing and then reinstalled before operating replace.
XG0903 - 150204.2
H Series Surround Installation
/