Montigo L-P-Series Surround Operating instructions

Brand: Montigo

Model: L-P-Series Surround

Type: Operating instructions

Montigo L-P-Series Surround

The Montigo L-P-Series Surround is a stylish and functional addition to any fireplace. It is constructed from high-quality materials and is designed to withstand the heat and flames of a fire. The surround is easy to install and can be customized to fit any fireplace.

The L-P-Series Surround is available in a variety of finishes, so you can choose the one that best matches your décor. It also comes with a variety of features, including:

A built-in heat shield to protect your walls from heat damage
Adjustable leveling feet to ensure a perfect fit
A powder-coated finish for durability and easy cleaning

Montigo L-P-Series Surround

The L-P-Series Surround is available in a variety of finishes, so you can choose the one that best matches your décor. It also comes with a variety of features, including:

A built-in heat shield to protect your walls from heat damage
Adjustable leveling feet to ensure a perfect fit
A powder-coated finish for durability and easy cleaning

XG0905 - 150204.3

Installing the L-Series and P-Series Fireplace Surround

Parts Included

1) 1-Pc, Surround

2) 2-Pcs, Attachment Brackets

3) 4-Pcs, Moving Brackets

4) 1-Pkg. Hardware

Tools Required

1) Power Drill, (eight 1/8" holes)

2) #8 Hexhead Driver, (to match hardware)

3) Carpenters level (Final Step, if required)

Installing the Surround

To install the Montigo Stainless steel or Black contemporary

surround onto the L-Series or P-Series unit, follow these steps.

Note: Four sided surround requires a raised installation.

Do not install nailing ange when installing four sided sur-

round. Refer to the installation and maintenance manual

for your replace for further information and framing

dimensions.

Step 1. Mark the location of the holes needed.

From the package of hardware locate one of the Attachment

Brackets. Hold this part in place as shown in Figure 2. With a

pencil or pen mark the (6) six holes on the face of the replace

frame, (see Figure 2.) Note: Ensure the brackets align with Figure

2. Below.

1”

Surround Dimensions (in inches)

Model M N O P

P38DF/L38 DF/ST 35 5/16" 19 7/16" 49 13/16" 34 1/16"

P42DF/L42 DF/ST 39 5/8" 20 5/16" 54 1/8" 34 15/16"

P52DF/L52 DF/ST 47 3/16" 21 13/16" 65 3/16" 40 3/8"

For Use with L-Series or P-Series

L38-DF/ST

L42-DF/ST

L52-DF/ST

P38-DF

P42-DF

P52-DF

REVISIONS

REV.

DESCRIPTION

DATE

CHANGED BY

- -

1:2

DWG. NO.

SHEET 1 OF 1

WEIGHT:

P38-MAN3

Finish

MATERIAL

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

1/32"

TWO PLACE DECIMAL

.015"

THREE PLACE DECIMAL

.005"

ALL BENDS ARE ASSUMED

TO BE 90

UNLESS NOTED

OTHERWISE.

Revision / Date

Drawn by

DATE

NAME

P38

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Y:\CADD\38\P38\P38

December-03-15 9:26:13 AM

SCALE

Description

FACEPLATE BRACKET

MANUAL

Revision

04/01/2015

Figure 1. Surround Dimensions (tolerance within 1/16")

Figure 2. Bracket Alignment

C US

ALIGN (2) ATTACHMENT BRACKETS

ON CENTER OF FRAME VERTICALS

(LEFT AND RIGHT SIDE TYPICAL

MOUNTING HOLES (3) PER SIDE

(LEFT AND RIGHT SIDE TYPICAL)

BRACKET TO BE

FLUSH WITH

OUTSIDE EDGE

OF FIREPLACE

(TYPICAL)

MOVING BRACKETS (2)

(LEFT AND RIGHT SIDE

TYPICAL)

BRACKETS TO

BE FLUSH WITH

TOP OF FIREPLACE

FRAME (TYPICAL)

REVISIONS

REV.

DESCRIPTION

DATE

CHANGED BY

- -

1:2

DWG. NO.

SHEET 1 OF 1

WEIGHT:

P38-MAN4

Finish

MATERIAL

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

1/32"

TWO PLACE DECIMAL

.015"

THREE PLACE DECIMAL

.005"

ALL BENDS ARE ASSUMED

TO BE 90

UNLESS NOTED

OTHERWISE.

Revision / Date

Drawn by

DATE

NAME

P38

PROPRIETARY AND CONFIDENTIAL

Y:\CADD\38\P38\P38

December-03-15 9:28:51 AM

SCALE

Description

FACEPLATE BRACKET

ALIGNMENT MANUAL

Revision

12/03/2015

Some materials used in the manufacturing process of this product can

expose you to Benzene which is known in the State of California to

cause cancer and birth defects or other reproductive harm. For more

information go to www.P65warnings.ca.gov

WARNING

XG0905 - 150204.3

Step 2. Drill holes.

Before you go any farther now is the time to double check

the location of the holes, do they agree with Figure 2. If

you are satised with the location of the holes, use a punch to

mark the holes, then using a 1/8" drill, drill out the six holes.

Step 3. Install the (2) two Attachment Brackets. (See

Figure 2)

Install the two (2) Attachment Brackets you used as a guide. Have

someone hold one of the Brackets in place, using the Hex-tool,

place a self-tapping #8-18 sheet metal hex screw into the hole

and twist it into the hole half way.

Follow this procedure for the remaining two (2) screws in the

rst bracket. After the three (3) screws are in place tighten them

in place. Repeat the procedure in Step 3 for the second Attach-

ment Bracket.

Step 4. Install the (2) two Movable Brackets. (If installed

disregard this step. If not See Figure 3)

Install the two (2) Movable Brackets. (These move up or down

to level and align the surround. This will produce a sym-

metrical reveal when correctly adjusted).

SECTION

A-A

FLUSH WITH

VALVE/BOTTOM

PANEL

REVISIONS

REV.

DESCRIPTION

DATE

CHANGED BY

- -

1:8

DWG. NO.

SHEET 1 OF 1

WEIGHT:

P38-MAN2

Finish

MATERIAL

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

1/32"

TWO PLACE DECIMAL

.015"

THREE PLACE DECIMAL

.005"

ALL BENDS ARE ASSUMED

TO BE 90

UNLESS NOTED

OTHERWISE.

Revision / Date

Drawn by

DATE

NAME

P38

PROPRIETARY AND CONFIDENTIAL

Y:\CADD\38\P38\P38

March-31-15 12:54:25 PM

SCALE

Description

FACEPLATE MANUAL

Revision

03/31/2015

SECTION

A-A

FLUSH WITH

VALVE/BOTTOM

PANEL

REVISIONS

REV.

DESCRIPTION

DATE

CHANGED BY

- -

1:8

DWG. NO.

SHEET 1 OF 1

WEIGHT:

P38-MAN2

Finish

MATERIAL

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

1/32"

TWO PLACE DECIMAL

.015"

THREE PLACE DECIMAL

.005"

ALL BENDS ARE ASSUMED

TO BE 90

UNLESS NOTED

OTHERWISE.

Revision / Date

Drawn by

DATE

NAME

P38

PROPRIETARY AND CONFIDENTIAL

Y:\CADD\38\P38\P38

March-31-15 12:54:25 PM

SCALE

Description

FACEPLATE MANUAL

Revision

03/31/2015

Figure 4. Installing the Movable Brackets on Lower Facia

Figure 5. Installing the Movable Brackets on Lower Facia

Cut Out

Lower Facia

Moveable Bracket

Lower Facia

REVISIONS

REV.

DESCRIPTION

DATE

CHANGED BY

- -

1:2

DWG. NO.

SHEET 1 OF 1

WEIGHT:

P38-MAN3

Finish

MATERIAL

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

1/32"

TWO PLACE DECIMAL

.015"

THREE PLACE DECIMAL

.005"

ALL BENDS ARE ASSUMED

TO BE 90

UNLESS NOTED

OTHERWISE.

Revision / Date

Drawn by

DATE

NAME

P38

PROPRIETARY AND CONFIDENTIAL

Y:\CADD\38\P38\P38

December-03-15 9:26:13 AM

SCALE

Description

FACEPLATE BRACKET

MANUAL

Revision

04/01/2015

10-24 Machine Screw

Moveable Bracket

Cut out

Figure 3. Installing the Movable Brackets

Pick up one of the brackets, using the supplied hardware, mount

it into place. Slide the bolt through the bracket 'front to back',

(See Figure 3), then tighten the bolt using a open end wrench

or socket.

Follow this procedure for the remaining bolt in the second Mov-

able Bracket.

Step 5. Installing the Lower Moveable Brackets

Using the self drilling screws supplied secure the moveable

brackets to the front of the replaces lower facia. The cut out on

the moveable braket should be such that the cut out is facing

up. The moveable bracket should be level with the top of the

replace lower facia and spaced evenly from left to right as to

support the weight of the surround. See Figure 4 and 5.

XG0905 - 150204.3

Step 6. Placing the Surround

Finally it's time to install the Stainless steel or Black Surround.

For this step it would be helpful to have someone help you hold

the surround in place.

Lift the surround over the four (4) Movable Brackets and slide

the surround downward. The surround should securely lock in

place in the cut out in the lower moveable brackets. Center the

surround left to right.If the surround doesn't clear the top or bot-

tom of the replace you will have to adjust the movable brackets

up or down. Remove the surround place it aside. Adjust the

bracket as required. Repeat as necessary.

Step 7. Final adjusting of the Surround

This step is not necessary if the surround ts tightly around the

replace, or the adjustment is acceptable. But, if your surround

has an uneven reveal, or unequal gap around/between the re-

place and surround, using a carpenters level adjust the Movable

brackets as needed.

Finally place the adjusted Surround back on the Brackets and

admire your Contemporary Montigo replace.

WARNING

When installing the replace - gas lines, ttings, accesso-

ries or any other objects cannot impede the proper

movement of the door buckles.

WARNING

Screen Barrier must still be used with the Surround.

The screen should only ever be removed for servic-

ing and then reinstalled before operating replace.

XG0905 - 150204.3

L & P Series Surround

Installation

Montigo L-P-Series Surround Operating instructions

Brand: Montigo

Model: L-P-Series Surround

Type: Operating instructions

Montigo L-P-Series Surround

The L-P-Series Surround is available in a variety of finishes, so you can choose the one that best matches your décor. It also comes with a variety of features, including:

A built-in heat shield to protect your walls from heat damage
Adjustable leveling feet to ensure a perfect fit
A powder-coated finish for durability and easy cleaning

Download PDF

report

Montigo L-P-Series Surround Operating instructions

Montigo L-P-Series Surround Operating instructions

Related papers

Other documents