Grizzly T1248 Owner's manual

Grizzly
Brand
Grizzly
Model
T1248
Type
Owner's manual

Grizzly T1248 is a heavy-duty beech workbench designed to be used with chairs or stools and double as a desk, making it ideal for close-in detail work such as soldering, assembly work, gunsmithing, etc. Featuring a solid beechwood top, all-steel frame construction, and re-inforced corners, it is rock-solid and built to last a lifetime with a maximum weight capacity of 2500+ lbs. The workbench can be assembled in approximately 30 minutes and comes with adjustable rubber feet to ensure stability on uneven surfaces.

Grizzly T1248 is a heavy-duty beech workbench designed to be used with chairs or stools and double as a desk, making it ideal for close-in detail work such as soldering, assembly work, gunsmithing, etc. Featuring a solid beechwood top, all-steel frame construction, and re-inforced corners, it is rock-solid and built to last a lifetime with a maximum weight capacity of 2500+ lbs. The workbench can be assembled in approximately 30 minutes and comes with adjustable rubber feet to ensure stability on uneven surfaces.

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
MODEL T1248/T1249
HEAVY-DUTY
BEECH WORKBENCH
INSTRUCTIONS
COPYRIGHT © NOVEMBER, 2017 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 11/17) #ES19299 PRINTED IN TAIWAN
Introduction
These workbenches are designed to be used with
chairs or stools and double as a desk, making
them ideal for close-in detail work such as solder-
ing, assembly work, gunsmithing, etc. Featuring a
solid beechwood top, all-steel frame construction,
and re-inforced corners —rock-solid and built to
last a lifetime.
V1.11.17
Description Qty
A. Workbench Top .......................................... 1
B. End Frames ................................................ 2
C. Upper Supports .......................................... 2
D. Lower Support ............................................ 1
E. Rubber Feet M10-1.5 x 35 .......................... 4
F. Hardware Bag ..............................................
—External Corner Braces .......................... 6
— Internal Corner Braces ............................ 6
—Button Hd Cap Screws M8-1.25 x 55 ... 22
— Flat Washers 8mm ................................ 40
— Lock Nuts M8-1.25 ................................ 18
—Wrench 13/14mm Open-Ends ................. 1
—Hex Wrench 5mm ................................... 1
G. Steel Bars
5
⁄8" x 11
3
⁄4" ................................. 8
Inventory
Specifications
• Workbench Top (Width x Length)
—T1248 ..........................................25" x 48"
—T1249 ..........................................25" x 72"
• Height ...................................................... 37"
• Maximum Weight Capacity ......... 2500+ lbs.
• Approximate Assembly Time .......30 Minutes
Figure 1. Model T1248 & T1249 Heavy-Duty
Beech Workbenches.
T1248
T1249
Figure 2. Inventory.
B
A
C
D
E
F
G
-2-
Model T1248/T1249 (Mfd. Since 11/17)
Assembly
4. Secure end frames and upper supports with
(4) external corner braces and (4) internal
corner braces, using (12) M8-1.25 x 55 but-
ton head cap screws, (24) 8mm flat washers,
and (12) M8-1.25 lock nuts (see Figure 5).
DO NOT fully tighten fasteners yet.
5. Secure end frames and lower support with
(2) external corner braces and (2) internal
corner braces, using (6) M8-1.25 x 55 but-
ton head cap screws, (12) 8mm flat washers,
and (6) M8-1.25 lock nuts (see Figure 6).
DO NOT fully tighten fasteners yet.
1. Lay workbench top upside-down on a
protected surface, such as cardboard or a
blanket.
Note: Bottom-side of workbench top has
threaded holes.
2. Attach each end frame to workbench top with
(2) M8-1.25 x 55 button head cap screws and
(2) 8mm flat washers (see Figure 3). DO NOT
fully tighten fasteners yet.
3. Attach each upper support to work-
bench top with (2) M8-1.25 x 55 button
head cap screws and (2) 8mm flat wash-
ers (see Figure 4). DO NOT fully tighten
fasteners yet.
Figure 3. End frame attached to workbench top.
x 2
End Frame
End of
Workbench Top
Figure 4. Upper support attached to workbench
top.
x 2
Side of
Workbench Top
Upper
Support
Figure 6. End frame and lower support secured
together with corner braces.
End Frame
x 6
Lower
Support
Figure 5. End frame and upper support secured
together with corner braces.
x 12
End Frame
Upper
Support
External
Corner
Brace
Internal
Corner
Brace
External
Corner
Brace
Internal
Corner
Brace
Model T1248/T1249 (Mfd. Since 11/17)
-3-
6. Thread (4) rubber feet into bottoms of end
frames (see Figure 7).
7. Turn workbench upright and make sure it is
centered over end frames and supports (not
leaning to one side or the other), then fully
tighten all fasteners.
8. Adjust feet as necessary to ensure work-
bench sits firmly on ground and does not
rock.
Option: Lay a level across workbench from
side-to-side and end-to-end when adjusting
feet.
Figure 8. Steel bars inserted.
End Support
Frame
Steel
Bars
Figure 7. Adjustable feet attached.
End Frame
Rubber
Foot
9. Insert steel bars through end support frames
as desired (see Figure 8).
Note: End frames have several
holes, allowing for numerous shelving and
racking configurations.
-4-
Model T1248/T1249 (Mfd. Since 11/17)
BUY PARTS ONLINE AT GRIZZLY.COM !
Scan QR code to visit our Parts Store.
T1248 Parts Breakdown
1
2
2
3
3
4
5
5
6
6
7
7
7
7
7
8
8
8
8
10
11
12
13
9
9
9
9
8
8
8
8
9
8
8
9
7
8
8
7
8
7
8
6
5
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT1248001 WORKBENCH TOP 25 x 48 x 1-3/4 8 PT1248008 FLAT WASHER 8MM
2 PT1248002 END FRAME 9 PT1248009 LOCK NUT M8-1.25
3 PT1248003 UPPER SUPPORT 10 PT1248010 RUBBER FOOT M10-1.5 X 35
4 PT1248004 LOWER SUPPORT 11 PT1248011 STEEL BAR 5/8 X 11-3/4
5 PT1248005 EXTERNAL CORNER BRACE 12 PT1248012 WRENCH 13/14MM OPEN-ENDS
6 PT1248006 INTERNAL CORNER BRACE 13 PT1248013 HEX WRENCH 5MM
7 PT1248007 BUTTON HD CAP SCR M8-1.25 X 55
Model T1248/T1249 (Mfd. Since 11/17)
-5-
T1249 Parts Breakdown
BUY PARTS ONLINE AT GRIZZLY.COM !
Scan QR code to visit our Parts Store.
1
2
2
3
3
4
5
5
6
6
7
7
7
7
7
8
8
8
8
10
11
12
13
9
9
9
9
5
8
7
8
8
7
8
9
8
8
9
8
7
8
8
8
6
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT1249001 WORKBENCH TOP 25 X 72 X 1-3/4 8 PT1249008 FLAT WASHER 8MM
2 PT1249002 END FRAME 9 PT1249009 LOCK NUT M8-1.25
3 PT1249003 UPPER SUPPORT 10 PT1249010 RUBBER FOOT M10-1.5 X 35
4 PT1249004 LOWER SUPPORT 11 PT1249011 STEEL BAR 5/8 X 11-3/4
5 PT1249005 EXTERNAL CORNER BRACE 12 PT1249012 WRENCH 13/14MM OPEN-ENDS
6 PT1249006 INTERNAL CORNER BRACE 13 PT1249013 HEX WRENCH 5MM
7 PT1249007 BUTTON HD CAP SCR M8-1.25 X 55
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Grizzly T1248 Owner's manual

Grizzly
Brand
Grizzly
Model
T1248
Type
Owner's manual

Grizzly T1248 is a heavy-duty beech workbench designed to be used with chairs or stools and double as a desk, making it ideal for close-in detail work such as soldering, assembly work, gunsmithing, etc. Featuring a solid beechwood top, all-steel frame construction, and re-inforced corners, it is rock-solid and built to last a lifetime with a maximum weight capacity of 2500+ lbs. The workbench can be assembled in approximately 30 minutes and comes with adjustable rubber feet to ensure stability on uneven surfaces.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents