CAME RBE4MT Owner's manual

Documentazione

Tecnica

T35

rev. 1.1

10/2005

©

CAME

CANCELLI

AUTOMATICI

119RT55-GB

EXTERNAL RECEIVER

MULTIUSER

GER

| ATOMO SERIES | SÉRIE ATOMO | BAUREIHE ATOMO | SERIE ATOMO

RBE4MT

CANCELLI AUTOMATICI

TECHNICAL CHARACTERISTICS

AM 433.92 MHz four-channel receiver to mount outside the automation device’s control

board. It can be matched with CAME series TOP432NA,

TOP434NA, TOP432M, TOP434M, TOP432S, T432,

T434, T438 and TAM432SA transmitters up to a

maximum of 999 units.

ABS outdoor container with IP54 protection level.

With an internal display screen that enables fast

transmitter memorization (max 999) and easy, sporadic

system maintenance (deletion/reset, addition or

change)

It also includes a Memory Roll to make a safety copy of

all the transmitters memorized.

N.B. All programming and system management

operations can also be done via PC with the

relevant software.

The board requires 12 or 24V AC/DC

Output function:

- OUT1 in monostable or bistable mode (see pg. 3)

- OUT2 in monostable mode with 1 to 300-second

adjustable timer (see pg. 3)

- OUT3 and 4 in monostable mode

N.B. – The receiver must always have an aerial.

- If there are more than one, do not install receivers at a distance shorter than 4-5 m from each other to

avoid operation irregularities.

- It is preferable to position the aerial at the highest point possible from level ground and far from buildings.

GB

75

180

224

104

87

-2-

ENGLISCH

MAIN COMPONENTS

1. Program display screen

2. 4-way dip switch

3. OUT2 relay setting trimmer

4. Reset key

5. Memory Roll connector board

6. RS232 connector for PC connection (to use cable RS232

7. Aerial connection terminal board

8. Device control connection terminal boards

9. 12/24V AC/DC power terminal boards

10.Memory Roll board

11. Program keys

P.C. BOARD RBE4MT

RBE4MT

UP

1 2 3 4

DOWN

CLEAR

OUT2

OUT3 OUT4

OUT1

NC NO C

0V

12V

24V

AC/DC

1234

ON

OUT TEMP

AB

MEMORY ROLL

1

2

4

5

7

9

11

10

3

6

8

MAIN COMPONENTS

ENGLISCH

-3-

1234

ON

MINIMUM activation time setting of

monostable relay in OUT2 output:

1 second

-MAXIMUM activation time setting of

monostable relay in OUT2 output:

300 seconds

1 e 2

Programming and Maintenance dip

switch, see pg. 7

3 ON Bistable relay in OUT1

3 OFF Monostable relay in OUT1

4 Not used

PROGRAMMING/MAINTENANCE INDEX

- General notes – read carefully

PROG A - Memorize the 1st transmitter (MASTER code )

PROG B - Memorize the next transmitters

Output activation list

PROG C - Prepare a 2nd MASTER code

PROG D - Change the password

PROG E - Save the settings on the Memory Roll board

MANU A - Add transmitters

MANU B - Delete transmitters

MANU C - Delete all the settings

MANU D - Recover the settings from the Memory Roll board

Technical Specifications

pag. 4

pag. 5

pag. 6

pag. 7

pag. 8

pag. 9

pag. 10

pag. 11

pag. 12

pag. 13

pag. 14

pag. 15

TRIMMER PROGRAMMING

FUNCTION SELECTOR

-4-

ENGLISCH

The first transmitter memorized will automatically be recognized by the board as the Master

transmitter (and placed in the first memory position).

The MASTER code will be the system’s main programming and maintenance “agent”. It

should therefore be kept by the person who is in charge of the management of automation

devices connected to the receiver.

To simplify the management of the installation, at the end of the pamphlet we have prepared

a “USER ARCHIVE” with a graph in which to enter the name of the user of each transmitter;

please keep this pamphlet together with the MASTER TX

Viewer A displays the numerical position of

the transmitter in the receiver’s memory (999

memorizable transmitters, including

Masters); a transmitter may be precisely

located from this position.

Viewers in state of attended with fed

card

BA

GENERAL NOTES

Viewer B shows how many OUT outputs are

linked during programming/maintenance

operations.

Flashing dots in the viewers means we are

in MASTER code memory positions (the first

one is always in the 001 position).

During programming/maintenance operations, the visors guide the operator during the

execution of procedures

ENGLISCH

-5-

FIRST BASIC SYSTEM PROGRAMMING OPERATION. THIS

PROCEDURE

ACTIVATES THE BOARD, WHICH IS

OTHERWISE

INACTIVE.

PROCEDURE

A Press key 1 on the receiver until the

writing |Sto| appears on viewer A and output

|1| on the viewer; Select the output with keys

3-4

B press the MASTER code key until the

/001//1/ appears.

C Check the MASTER code settings by

pressing the same key again. The message

that appears must be as shown below

A

B

C

PROG A - MEMORIZATION OF THE FIRST TRANSMITTER (MASTER TX)

UP

1 2 3 4

DOWN

A

UP

1 2 3 4

DOWN

A

-6-

ENGLISCH

AFTER MEMORIZING THE MASTER CODE, HAVE ALL

THE

TRANSMITTERS AT HAND FOR FAST MEMORIZATION.

THE FOLLOWING PROCEDURE SHOULD ALSO BE USED

IF

OTHER TRANSMITTERS ARE ADDED LATER ON *

PROCEDURE

A Press the MASTER code key (10")

until the message

|Sto|

+

|linked output number|

appears on the viewer (after another 5") and

the transmitter’s LED indicator remains lit;

B Select the output or outputs with keys

3-4 (output list on pg. 7).

C Press the corresponding key on the

transmitter to be memorized within 20": the

message on the viewers flashes. Continue

this way for every transmitter to be

memorized for that same output.

D Repeat step B with the corresponding

transmitter key.

C

P2

master

coder

B

D

P2

A

master code

12

6

3

9

1

2

4

57

8

10

11

10"

12

6

3

9

1

2

4

57

8

10

11

15"

Led

P1

PROG B - TRANSMITTER MEMORIZATION

......

RBE4MT

UP

1 2 3 4

DOWN

CLEAR

OUT2

OUT3 OUT4

OUT1

NC NO C

0V

12V

24V

AC/DC

1234

ON

OUT TEMP

AB

UP

1 2 3 4

DOWN

A

ENGLISCH

-7-

OUTPUT ACTIVATION LIST

OUT2

OUT3 OUT4

OUT1

NC NO C

NO C

B

BB

ON

ON ON

ON

ON ON

ON ON ON

ON

B

BB

ON ON

ON ON ON

ON ON

ON ON ON

ON ON ON ON

OUT2

OUT3 OUT4

OUT1

NC NO C

NO C

3 4

THIS TABLE IS FOR VIEWING WHICH OUTPUTS ARE SELECTED ACCORDING TO THE ALPHANUMERICAL VALUE

ENTERED

IN VIEWER B

-8-

ENGLISCH

SHOULD IT PROVE NECESSARY, IT IS POSSIBLE TO

CONFIGURE

ANY OF THE ALREADY MEMORIZED

TRANSMITTERS

AS THE SECOND MASTER CODE.

PROCEDURE

A Press any key on the transmitter to

be configured as second Master and read

the memory position occupied on viewer A;

B set dip switch 2 to ON (viewer A

displays the first available memory position

while viewer B displays a flashing

|P|

);

C use the UP and DOWN keys to select

the transmitter’s position as in step A;

D press the MASTER code key (10")

until the writing

|M|,

including the dots, flashes

on viewer B;

E reset dip switch 2 to OFF.

N.B. Only one MASTER code may be

configured in addition to the first one; if the

procedure is repeated with another TX, it

automatically replaces the previous one.

A

B

1234

ON

ESEMPIO

C

DOWN=13/12/11.........3/2/1/999/998/...

UP=13/14/15...........998/999/1/2/3.....

D

12

6

3

9

1

2

4

57

8

10

11

10"

1° Master code

E

1234

ON

ESEMPIO

PROG C - PREPARE A SECOND MASTER CODE

RBE4MT

UP

1 2 3 4

DOWN

CLEAR

OUT2

OUT3 OUT4

OUT1

NC NO C

0V

12V

24V

AC/DC

1234

ON

OUT TEMP

AB

UP

1 2 3 4

DOWN

ENGLISCH

-9-

A

1234

ON

B

CLEAR

1234

OUT TEMP

PROCEDURE

A Position dip switches 1 and 2 to ON:

the writing |001| + |C| appears on the

viewers;

B press CLEAR: the writing changes to

|000| + |c| with the “c” flashing;

C use the UP and DOWN keys to select

the existing password (in the example the

one preset);

D press CLEAR (the entire |123| + |c|

writing flashes) and after 5", press key 4 (the

writing changes to |000| + |c| with the “c”

flashing);

E enter the new password using the UP

and DOWN keys;

F press CLEAR (the steadily lit letter

|m| appears on viewer B), and reset dip

switches 1 and 2 to OFF.

N.B. The new password may even be

made up of one digit

F

CLEAR

1234

UT TEMP

1234

ON

C

UP

1 2 3 4

DOWN

DOWN=13/12/11.........3/2/1/999/998/...

UP=13/14/15...........998/999/1/2/3.....

ESEMPIO

1,2,3 is the password

preset by CAME

D

CLEAR

1234

O

UT TEMP

3 4

12

6

3

9

1

2

4

57

8

10

11

5"

E

DOWN=13/12/11.........3/2/1/999/998/...

UP=13/14/15...........998/999/1/2/3.....

select a new

password (a number

between 1 and 511)

UP

1 2 3 4

DOWN

PROG D - PASSWORD CHANGE

A

-10-

ENGLISCH

ONCE THE INSTALLATION IS COMPLETED, USE THE

MEMORY ROLL BOARD TO SAVE THE SETTINGS MADE

ON

THE RECEIVER.

PROCEDURE

A Insert (*) the Memory Roll board in

the relevant connector;

B first press the MASTER code key

and

keep it pressed, and then press key 2

on the receiver; Release both of them (10")

only when the |U| appears on viewer B;

C remove (*) the Memory Roll board and

file it.

A

UP

1 3 42

DOWN

CLEAR

OUT1 OUT2

OUT3 OUT4

NC NO C

0V

12V

24V

AC/DC

NO C

1234

ON

OUT TEMP

AB

MEMORY ROLL

B

UP

1 2 3 4

DOWN

12

6

3

9

1

2

4

57

8

10

11

10"

All 255 memory blocks transferred over to

the Memory Roll board are displayed on

viewer A in rapid succession.

A

BEFORE

LATER

C

* WARNING! Before connecting or

disconnecting boards, please make sure the

power supply is turned is off.

PROG E - SAVING DATA ON THE MEMORY ROLL BOARD

UP

1 3 42

DOWN

CLEAR

0V

12V

24V

1234

ON

OUT TEMP

AB

MEMORY ROLL

ENGLISCH

-11-

THERE ARE TWO WAYS TO ADD TRANSMITTERS:

- ADD THEM IN SEQUENCE, THAT IS, MEMORIZE

THEM

ON THE FIRST AVAILABLE POSITION* IN THE

MEMORY

(SEE PROG B)

- OR (THIS PROCEDURE) ADD THEM IN A CHOSEN

AVAILABLE

POSITION.

PROCEDURE

A Position dip switch 2 to ON: the

viewers display the flashing message:

|1st

available position|

+

|P|

;

B use the UP and DOWN keys to

select another available position in which

to add the transmitter;

C Select the output or outputs with

keys 3-4 (output list on pg. 7); the writing

|Sto|

appears;

D Press the MASTER code key and

|Sto|

begins to flash;

E press (within 20") the transmitter’s

new key: after a few seconds the writing

on the viewer will stop flashing and remain

fixed;

F reset dip switch 2 to OFF.

* The first available position could be

the position after the last memorized

transmitter, or an intermediate position

that belonged to a transmitter that has

been eliminated (see MANU B)

A

1234

ON

ESEMPIO

B

UP

1 2 3 4

DOWN

A

DOWN=13/12/11.........3/2/999/998/...

UP=13/14/15...........998/999/1/2/3.....

If the P does not flash, it

means that that position is

not available

ESEMPIO

F

E

12

6

3

9

1

2

4

57

8

10

11

2"

1234

ON

C

MANU A - ADDING TRANSMITTERS

UP

1 2 3 4

DOWN

D

-12-

ENGLISCH

ONE OR MORE TRANSMITTERS MAY BE ELIMINATED

FROM

THE SYSTEM (TO ELIMINATE ALL OF THEM, ALL

THE

SETTINGS MUST BE DELETED, SEE MANU D).

POSITIONS CLEARED THIS WAY MAY LATER ON BE USED

BY

ANOTHER TRANSMITTER (SEE MANU A)

PROCEDURE

A Press any key of the transmitter to

be eliminated and read the memory position

it occupies on viewer A;

B Position dip switch 1 to ON: the

steadily lit message

|001|

+

|C|

appears;

C use the UP and DOWN keys to select

the position of the transmitter to be deleted;

D press any MASTER code key: the

|C|

flashes on viewer B;

E reset dip switch 1 to OFF.

D

Master code

E

1234

ON

C

UP

1 2 3 4

DOWN

DOWN=13/12/11.........3/2/1/998/999/...

UP=13/14/15...........998/999/1/2/3.....

B

1234

ON

A

ESEMPIO

MANU B - DELETING A TRANSMITTER

RBE4MT

UP

1 2 3 4

DOWN

CLEAR

OUT2

OUT3 OUT4

OUT1

NC NO C

0V

12V

24V

AC/DC

1234

ON

OUT TEMP

AB

ENGLISCH

-13-

WHEN THIS PROCEDURE IS COMPLETED, THE MEMORY

WILL

BE EMPTY AND THE BOARD INACTIVE.

TO RESET THE SETTINGS FROM THE MEMORY ROLL

BOARD

, FIRST REMEMORIZE THE MASTER TX WITH

THE

PROG A PROCEDURE

WARNING! THE MASTER CODE MUST BE THE

SAME ONE WITH WHICH THE SETTINGS WERE SAVED

ON THE MEMORY ROLL BOARD.

PROCEDURE

A First position dip switch 1 and then 2

at ON: the message

|001|

+ |

C|

appears on the

viewers;

B press CLEAR: the |

c|

flashes on

viewer B;

C select the password with the UP and

DOWN keys;

D press CLEAR (the entire

|password

|

+

|c|

message flashes) and press key 3 within

5"(the writing changes from

|CLr|

+ |

A|

to

|001|

+ |

C|

with the C flashing);

E reset dip switches 1 and 2 to OFF.

A

1234

ON

B

CLEAR

1234

OUT TEMP

C

UP

1 2 3 4

DOWN

DOWN=13/12/11.........3/2/1/511/510/...

UP=13/14/15...........510/511/1/2/3.....

1,2,3 is the password

preset by CAME

ESEMPIO

E

1234

ON

D

CLEAR

1234

UT TEMP

2 3 4

DOWN

12

6

3

9

1

2

4

57

8

10

11

5"

MANU D - DELETION OF THE ENTIRE PROGRAMMING

-14-

ENGLISCH

THE SETTINGS PREVIOUSLY SAVED BY THE MEMORY

ROLL BOARD (SEE PROG F) CAN BE RECOVERED

AT

ANY TIME.

WARNING! THE MASTER CODE MUST BE THE

SAME ONE WITH WHICH THE SETTINGS WERE SAVED

ON THE MEMORY ROLL BOARD.

PROCEDURE

A Insert (*) the Memory Roll board in

the relevant connector;

B first press any MASTER TX key and

keep it pressed, and then press key 1 on

the receiver; Release both of them (10") only

when the |P| appears on viewer B;

C remove (*) and file away the Memory

Roll board.

A

B

UP

1 2 3 4

DOWN

12

6

3

9

1

2

4

57

8

10

11

10"

All 255 memory blocks transferred over to

the Memory Roll board are displayed on

viewer A in rapid succession

A

PRIMA

DOPO

C

* WARNING! Before connecting or

disconnecting boards, please make sure the

power supply is turned is off.

MANU E - DATA RECOVERY FROM THE MEMORY ROLL BOARD

UP

1 3 42

DOWN

CLEAR

OUT1 OUT2

OUT3 OUT4

NC NO C

0V

12V

24V

AC/DC

NO C

1234

ON

OUT TEMP

AB

MEMORY ROLL

UP

1 3 42

DOWN

CLEAR

1234

ON

OUT TEMP

AB

MEMORY ROLL

ENGLISCH

-15-

TECHNICAL SPECIFICATIONS

FREQUENCYFREQUENCY

FREQUENCY

: 433.92 MHz: 433.92 MHz

: 433.92 MHz

INPUT IMPEDENCEINPUT IMPEDENCE

INPUT IMPEDENCE

: 52 Ohm: 52 Ohm

: 52 Ohm

1mV SENSITIVITY FOR SUCCESSFUL COMPLETION SIGNAL1mV SENSITIVITY FOR SUCCESSFUL COMPLETION SIGNAL

1mV SENSITIVITY FOR SUCCESSFUL COMPLETION SIGNAL

100 ÷ 150 m A100 ÷ 150 m A

100 ÷ 150 m A

VERAVERA

VERA

GE RANGE WITH AERIALGE RANGE WITH AERIAL

GE RANGE WITH AERIAL

MODULAMODULA

MODULA

TIONTION

TION

: OOK: OOK

: OOK

INPUT AINPUT A

INPUT A

T RESTT REST

T REST

: 100 mA: 100 mA

: 100 mA

INPUT WITH AINPUT WITH A

INPUT WITH A

CTIVE CHANNELCTIVE CHANNEL

CTIVE CHANNEL

: 175mA: 175mA

: 175mA

N° OF CHANNELSN° OF CHANNELS

N° OF CHANNELS

: 4: 4

: 4

RELARELA

RELA

Y CONTY CONT

Y CONT

AA

A

CTCT

CT

: 10° 250V: 10° 250V

: 10° 250V

CAME LOMBARDIA S.R.L.___COLOGNO M. (MI)

(+39) 02 26708293 (+39) 02 25490288

CAME SUD S.R.L. _________________NAPOLI

(+39) 081 7524455 (+39) 081 7529109

CAME (AMERICA) L.L.C._________MIAMI (FL)

(+1) 305 5930227 (+1) 305 5939823

CAME AUTOMATISMOS S.A_________MADRID

(+34) 091 5285009 (+34) 091 4685442

CAME BELGIUM____________LESSINES

(+32) 068 333014 (+32) 068 338019

CAME CANCELLI AUTOMATICI S.P.A.

DOSSON DI CASIER (TREVISO)

(+39) 0422 4940 (+39) 0422 4941

CANCELLI AUTOMATICI

CAME FRANCE S.A.___NANTERRE CEDEX (PARIS)

(+33) 01 46130505 (+33) 01 46130500

CAME GMBH____KORNTAL BEI (STUTTGART)

(+49) 07 11839590 (+49) 07 118395925

CAME GMBH________SEEFELD BEI (BERLIN)

(+49) 03 33988390 (+49) 03 339885508

CAME PL SP.ZO.O_________WARSZAWA

(+48) 022 8365076 (+48) 022 8369920

CAME UNITED KINGDOM LTD___NOTTINGHAM

(+44) 01159 387200 (+44) 01159 382694

A

SSISTENZA TECNICA

NUMERO VERDE

800 295830

W

EB

www.came.it

E-

MAIL

[email protected]

SISTEMA QUALITÀ

CERTIFICATO

CAME RBE4MT Owner's manual

CAME RBE4MT Owner's manual

Related papers

Other documents