EasyAccess Innovations EA1126TL User guide

Brand: EasyAccess Innovations

Model: EA1126TL

Type: User guide

EasyAccess Innovations EA1126TL is a telescopic ladder that provides a safe and reliable service with proper use and care. It is very portable and can be carried easily. The ladder can be opened to full height or to any interim height, making it suitable for various tasks. The locking mechanisms ensure that the ladder is properly engaged before use, and the bottom pull rings lock in the up position for added safety. The ladder should be treated with care to avoid damage to the tubes, which may affect its operation.

Use and Care Instructions for the

EasyAccess Telescopic Ladder

READ ALL INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO USE THE LADDER

DO NOT OPEN THE LADDER FROM THE TOP UNLESS

EXTENDING TO FULL HEIGHT. IT MAY COLLAPSE!

With proper use and care, your EasyAccess Innovations

Telescopic Ladder will provide you with a safe and reliable

service. Please read and follow these instructions carefully.

Save this booklet for future reference.

[email protected]

www.easyaccessinnovations.com

IMPORTANT

WARNING!

FOR VISUAL INSTRUCTIONS,

PLEASE GO TO OUR YOUTUBE VIDEO

ATTENTION!

OPENING YOUR LADDER

FULL EXTENSION

1. The EasyAccess Innovations Telescopic

Ladder is very portable and should be

carried as shown in Figure 1

2. To begin the opening process, place the

ladder on a firm level surface and stabilize

with your foot as shown in Figure 2

IMPORTANT:

DO NOT OPEN LADDER FROM THE TOP

UNLESS OPENING TO THE FULL HEIGHT.

SECTIONS MAY NOT PROPERLY LOCK

AND YOU COULD BE INJURED

3. There are two (2) ways to OPEN your

ladder. Full extension or extension to any

interim height.

IMPORTANT:

NEVER USE THE LADDER BEFORE

ASSURING THAT THE LOCKING

MECHANISMS ARE PROPERLY ENGAGED.

NEVER PULL BOTTOM LOCKING RINGS

OR PUSH UP ON ANY RED LOCKING

LEVERS WHEN LADDER IS IN USE.

1. To open ladder to full height, use the

following procedure:

a. To begin the opening process, place the

ladder on a firm level surface and stabilize

with your foot. Figure 2

b. Starting with the top rung, Figure 3,

open each section to its full extension (one

section at a time) until all sections are fully

open. Figure 4 & Figure 5

c. Check to be sure the red locking levers

are at an angle of approximately 60

degrees, indicating that the locking

mechanisms are properly engaged.

Figure 6

NOTE: THE BOTTOM PULL RINGS LOCK IN

THE UP POSITION.

Figure 1 Figure 2

Figure 3

Figure 5

Figure 6

Red Locking

Levers:

Locked

position

for all red

levers

except

bottom

pull rings.

Always ensure

that the red

locking

mechanism

have fully

engaged

by checking

that the red

locking levers

have dropped

to an angle of

approximately

60 degress

UNLOCKED

POSITION

DOWN

LOCKED

POSITION

BOTTOM PULL

RINGS

Figure 4

CLOSING THE LADDER

INTERIM HEIGHT EXTENSION

IMPORTANT:

DO NOT LOWER THE LADDER TO INTERIM

HEIGHTS. ALWAYS CLOSE LADDER

COMPLETELY AND THEN RE-OPEN TO

DESIRED HEIGHT.

Care should be taken when closing the

ladder. Unlocking and closing is quite

simple when done carefully.

To close the ladder, refer to Figure 7

and proceed as follows:

1. Hold the ladder upright and firmly grasp

one of the open vertical tubes with one hand.

2. With your other hand, pull down the

ringed locking levers ONE AT A TIME, to

release the bottom locks.

(Sometimes it is

necessary to pull the first ring a second time)

3. When the bottom locks are released,

the ladder is easily closed by CAREFULLY

and SLOWLY telescoping each section

down, keeping your hands on the tubes,

NOT ON THE RUNGS. The ladder will

unlock itself automatically as you lower

each section.

4. Store the ladder indoors.

a.For opening ladder to any interim height,

always open from the ladder rung of your

desired height chosen.

After you have chosen your desired height

or chosen ladder rung height, grasp the

outside edges of the rung chosen and pull

up. Figure 8

b. Open each section one at a time until all

sections are fully opened to your desired

interim height. Figure 9

Be sure all red indicator levers under each

ladder rung and pull rings under bottom

ladder rung are in locking position before

climbing ladder. Refer to figure 6

Pulling down rings

one at a time to

unlock ladder

Figure 7

Figure 8

Figure 9

IMPORTANT:

USE CARE. NEVER PULL BOTH RINGS

SIMULTANEOUSLY

IMPORTANT:

NEVER PUT ANY PART OF YOUR BODY,

INCLUDING YOUR HANDS, FINGERS OR

THUMBS ON OR BETWEEN THE RUNGS

WHEN CLOSING THE LADDER.

IMPORTANT:

DO NOT START INTERIM HEIGHT BY

BEGINING WITH BOTTOM RUNG BUT ONLY

IF THAT IS THE CHOSEN DESIRED HEIGHT

IMPORTANT:

THIS STEP IS REQUIRED TO ASSURE

SAFE OPERATION FOR INTERIM

HEIGHTS

NOTE THAT THE BOTTOM LOCKING

LEVERS WITH PULL RINGS LOCK IN

THE UP POSITION.

e. If any locking levers are not at the

proper angle, lift the ladder by the tubes

and gently tap on the ground. This will

normally bring the locking levers to correct

angle.

IMPORTANT:

NEVER USE THE LADDER BEFORE

ASSURING THAT THE LOCKING

MECHANISMS ARE PROPERLY ENGAGED.

NEVER PULL RINGED LOCKING LEVERS

WHEN LADDER IS IN USE.

c. (Important) If the chosen height is in

fact not the height desired and need to

adjust height either higher or lower, you

must reset the ladder by lowering the

ladder back down into starting position by

pulling the release rings located on

first/bottom rung. Figure 7

Allow ladder to completely descend with

each rung stack onto one another.

Figure 10

d. Now select your new desired height and

grasp outside edge of newly chosen rung

(height) Figure 11 and pull up to fully

extend all rungs below. Figure 12

Make sure that all red locking levers are in

their locking positions and bottom rung

pull rings are in their locking positions.

Figure 12

UNLOCKED

POSITION

DOWN

LOCKED

POSITION

Figure 12

Figure 10

Red Locking

Levers:

Locked

position

for all red

levers

except

bottom

pull rings.

Always ensure

that the red

locking

mechanism

have fully

engaged

by checking

that the red

locking levers

have dropped

to an angle of

approximately

60 degress

Figure 11

BOTTOM PULL RINGS

SAFETY PROCEDURES

Check to ensure all locking mechanisms are

properly engaged before climbing the ladder

Always open and close the ladder in a slow and

careful manner

Treat the ladder with care. It is a precision built

product. If tubes are dented or damaged in any

way, the ladder may be difficult to open or close,

or may completely malfunction

Always lean ladder against top rungs, never

against tubes, as they may become damaged

Keep your ladder clean occasionally wipe tubes

with a clean, dry cloth. Paint should be cleaned

off immediately as it will impede telescoping

action If stiffness develops, wipe tubes with a

clean clothand apply a small amount of silicone

spray wiping any excess with a clean cloth

Store your ladder indoors to avoid damp

conditions which could make the ladder difficult

to operate

Read and follow additional safety information

labels provided on your ladder

SAFETY PRECAUTIONS

DO NOT

Climb ladder at incline less than 75°

DO NOT

Place your hands, fingers or thumbs on or

between rungs when closing the ladder

DO NOT

Use your ladder if there is any doubt about the

locks being properly engaged, as this is an

unsafe condition

DO NOT

Pull ringed locking levers or tamper with other

locking levers when ladder is in use

IT MAY COLLAPSE

DO NOT

Carry, operate or use your ladder near electrical

wires or equipment

THIS LADDER CONDUCTS ELECTRICITY

DO NOT

Place a box or other objects under the ladder to

gain extra height. Always have a firm level base

for ladder to stand on

DO NOT

Use the ladder in a horizontal position, such as

saw horse. Never open or use the ladder upside

down as it could cause damage to the product

or cause bodily injury

DO NOT

Use ladder as scaffold or plank

DO NOT

Use ladder as a bridge

POINTS TO REMEMBER

As with any tools, safety should always be the

first consideration when using your telescopic

ladder.

Always check locking levers for proper locked

position before climbing.

Do not stand or climb on the top three sections

of the ladder when fully extended.

Never pull ringed locking or tamper with other

locking levers while ladder in use.

Do not lower the ladder to other interim heights.

Always close ladder fully and then reopen to

desired height.

Always close your ladder in a careful, controlled

manner remembering to avoid placing hands,

fingers or thumbs on or between rungs.

When standing on the ladder, do not over reach

or push/pull ladder to change its position.

Always face the ladder and do not climb up the

side.

Whenever possible, the ladder should be

secured in position.

Special care should be used on a windy day

Keep your ladder clean.

Store indoors in the closed position.

EASYACCESS INNOVATIONS RESERVES THE

RIGHT TO ALTER OR IMPROVE THE

PRODUCTS WHEN THEY SEE FIT

WARRANTY

Your EasyAccess ladder is covered by a

12-month warranty. The Company

undertakes to replace or repair, free of

charge, any defect that the Company

considers to be due to faulty workmanship

or material within 12 months of the sale

date, except for:

• Defects arising from neglect, misuse

or unauthorized modifications.

• Damage caused by abuse, misuse,

dropping or other similar damage

caused by or as a result of failure to

follow transportation, storage, loading

or operation, instructions.

• Alterations, additions or repairs carried

out by persons other than the

Manufacturer or their recognized

distributors.

• Transportation or shipment costs to

and from the Manufacturer or their

recognized agents, for repair or

assessment against a warranty claim,

on any EasyAccess ladder or

component.

• Materials and/or labor costs to renew,

repair, or replace components due to

normal wear and tear.

• Faults arising from the use of

non-standard or additional parts, or

any consequential damage or wear

caused by the fitting or use of such

parts.

EASYACCESS INNOVATIONS

4850 Murrieta St,

Chino, CA 91710, USA

(800) 980-8841

IMPORTANT

The Manufacturer and/or their recognized

agents, directors, employees or insurers

will not be held liable for consequential or

other damages, losses or expenses in

connection with, or by reason of, or the

inability to use the EasyAccess ladder for

any purpose.

MODIFICATIONS

If additional equipment or any third party

work, modifications or alterations are to be

carried out on the EasyAccess ladder

which will involve any welding, drilling or

any form of cutting or distortion of

materials, full written approval must be

obtained from the Manufacturer prior to

the work being carried out.

REPLACEMENT PARTS INFORMATION

For information on replacement parts, visit

our website where you can download

illustrations and part listings.

www.easyaccessinnovations.com

EasyAccess Innovations GUARANTEE CARD

EasyAccess Innovations Telescopic Ladder

LADDER NUMBER:

PURCHASER NAME:

ADDRESS:

TOWN: ZIP CODE:

DATE OF PURCHASE:

THE USE OF THE TELESCOPIC LADDER AS WELL AS ALL SAFETY

INSTRUCTIONS HAVE BEEN FULLY EXPLAINED TO ME.

PURCHASER’S SIGNATURE:

For EasyAccess Innovations use only

EasyAccess Innovations GUARANTEE CARD

EasyAccess Innovations Telescopic Ladder

LADDER NUMBER:

PURCHASER NAME:

ADDRESS:

TOWN: ZIP CODE:

DATE OF PURCHASE:

THE USE OF THE TELESCOPIC LADDER AS WELL AS ALL SAFETY

INSTRUCTIONS HAVE BEEN FULLY EXPLAINED TO ME.

PURCHASER’S SIGNATURE:

For EasyAccess Innovations use only

EASYACCESS INNOVATIONS

4850 Murrieta St,

Chino, CA 91710

USA

EasyAccess Innovations GUARANTEE CARD

Your EasyAccess Innovations Telescopic Ladder is a quality product. Manufactured with

great precision using carefully selected materials. We guarantee this branded product for a

period of 12 months in the event of any defects which may be traced back to a fault in

material or manufacturing. The guarantee entitlement begins on the date of receipt of this

guarantee card by the main importer (date of postmark).

In addition to the statutory rights, this guarantee entitles EasyAccess Innovations to repair

or replace at their discretion.

The guarantee becomes null and void in the event of proven improper use.

EASYACCESS INNOVATIONS

4850 Murrieta St,

Chino, CA 91710

USA

Place

Stamp

Here

EasyAccess Innovations EA1126TL User guide

Brand: EasyAccess Innovations

Model: EA1126TL

Type: User guide

Download PDF

report

EasyAccess Innovations EA1126TL User guide

EasyAccess Innovations EA1126TL User guide

Other documents