Page is loading ...
CAUTION
Some parts may have sharp edges. Take care when handling or wear protective
gloves.
PARTS LIST/DIAGRAM
Key Qty. Description Part No.
A . . . . . 1 . . . . . Main Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3499473
B . . . . . 3 . . . . . Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3498382
C. . . . . 1 . . . . . Charcoal Grate, Small . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3498574
Cooking Grate, Large . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3499731
D. . . . . 1 . . . . .
Note: Illustrations are not to scale.
1/4”-20NC Wingnut, Bright Zinc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .HWS02520BR
G. . . . 6 . . . . .
Auger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3498792
E. . . . . 1 . . . . .
1/4”-20NC X 3/4” Long Thumb Screw, Bright Zinc . . . . . . . . . . . . . . . . . . . . . . . . .TS02520075BR
H . . . . 1 . . . . .
1/4”-20NC X 1 3/4”, Long Hex Head Bolt, Bright Zinc . . . . . . . . . . . . . . . . . .HB025201750HHBR
F. . . . . 6 . . . . .
AB C
DE
FG H
2
STEP 1
1. In a flat area, hold the Auger upright with the Auger tip on the ground.
2. Place the Main Post Turn Bar into “U” shaped cutouts in the Auger cylinder, as shown in figure below
3. Turn the Auger until Auger is complete screwed into the ground. Be sure to keep the Auger perpendicular to the ground.
NOTE: The Thumb Screw hole face away from the fire pit.
“CLOCKWISE”
MUST
STEP 2
1. Slide Main Post into Auger cylinder as shown below.
2. Attach Main Post to Auger cylinder with Thumb Screw as shown below.
2. Attach (3) Mounting Brackets to Main Post using (3) Hex Head Bolts and (3) Wing Nuts as shown in figure below. Tighten securely.
NOTE: Thumbscrew MUST be on opposite side of Main Post
from Mounting Brackets.
Main Post
Main Post
Thumb Screw
Hole
Fire Pit
Turn Bar
Auger
Hex Bolt
Wing Nut
Main Post
Mounting Bracket
3
Main Post
Auger
Cylinder
Thumb Screw
STEP 3
1. Place Charcoal Grate (small Grate) into lower bracket.
2. Place Cooking Grate (large Grate) into center or upper bracket.
NOTE:
To add or remove food from Cooking Grate, loosen Thumb Screw in Main Post and swivel Cooking Grate 180 degrees away from fire pit as
shown below.
Cooking Grid
Main Post
Fire Pit
Cooking Grate
Large Grate
Charcoal Grate
Small Grate
4
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
INSTRUCCIONES DE ARMADO
PARRILLA RAMBLER
9
Page is loading ...
Page is loading ...
Page is loading ...
/
