KVH Industries TracVision R4SL Installation And Operation Instructions Manual

KVH Industries
Brand
KVH Industries
Model
TracVision R4SL
Type
Installation And Operation Instructions Manual

This manual is also suitable for

KVH Industries TracVision R4SL is a satellite TV system designed for recreational vehicles, allowing you to enjoy your favorite shows and movies on the go. With automatic satellite acquisition and tracking, you can easily access channels from DISH Network, DIRECTV, and Bell TV, including popular HD channels. The R4SL features a compact, low-profile dome antenna for easy installation on your RV's roof, and it works seamlessly with your existing TV and receiver.

KVH Industries TracVision R4SL is a satellite TV system designed for recreational vehicles, allowing you to enjoy your favorite shows and movies on the go. With automatic satellite acquisition and tracking, you can easily access channels from DISH Network, DIRECTV, and Bell TV, including popular HD channels. The R4SL features a compact, low-profile dome antenna for easy installation on your RV's roof, and it works seamlessly with your existing TV and receiver.

KVH, TracVision, and the unique light-colored dome with contrasting baseplate are registered trademarks of KVH Industries, Inc.
All other trademarks are property of their respective companies. The information in this document is subject to change without notice.
No company shall be liable for errors contained herein. © 2008 KVH Industries, Inc., All rights reserved. 54-0445 Rev. F
1
The following instructions explain how to install and operate the Tri-Sat AutoSwitch Kit on a
TracVision R5SL/R5/R4SL/R4 system.
The Tri-Sat AutoSwitch Kit allows DIRECTV HDTV subscribers to enjoy the Ku-band portion of
the overall high-definition (HD) programming package and switch automatically among the
DIRECTV 101, 110, and 119 satellites when using a DIRECTV H21-200 or H20-600 receiver.
NOTE: This procedure requires a PC with the latest version of the KVH Flash Update Wizard installed.
The Flash Update Wizard is available to KVH-authorized dealers through the KVH Partner Portal.
Who Should Install the System?
To ensure a safe and effective installation, KVH recommends that a KVH-authorized technician
install the Tri-Sat AutoSwitch Kit. To find a technician near you, please visit www.kvh.com/
wheretogetservice.
Technical Support
If you need technical assistance, please contact KVH Technical Support:
For information on: Refer to:
Installation Page 2
Operation Page 6
Advanced Wiring
Diagrams
Page 9
Phone: +1 401 847-3327
E-mail: [email protected]
KVH Tri-Sat AutoSwitch
™
Kit Installation and Operation
Instructions for TracVision
®
R5SL/R5/R4SL/R4
2
Installing the Tri-Sat AutoSwitch
Kit
This section explains how to install the Tri-Sat
AutoSwitch Kit. These instructions require
additional/alternate installation steps than those
specified in the TracVision Installation Guide.
These instructions supersede the TracVision
installation and operation instructions where
applicable.
Step 1 - Set Up the System
The following instructions explain how to
modify the TracVision system for Tri-Sat
AutoSwitch use.
Upgrading Previously Installed TracVision Systems
If you are installing the Tri-Sat AutoSwitch Kit to
upgrade a TracVision system that is already
installed on a vehicle, follow the steps below:
a. Systems with a grounding block -
Disconnect any components connected to the
grounding block’s RF1 connector (see
Figure 1).
Systems without a grounding block -
Disconnect any components connected to the
antenna’s RF1 cable (see Figure 2).
b. Proceed to “Step 2 - Connect the Tri-Sat
AutoSwitch Kit” on page 3
CAUTION
For your own safety, be sure to disconnect
power from all wired components before
performing this procedure.
Figure 1 Disconnecting Components with Grounding Block
Figure 2 Disconnecting Components without Grounding Block
Antenna
RF1RF2
Grounding
Block
Vehicle
AC Ground
To Connected
Component(s)
Disconnect
Here
To Connected
Component(s)
To Connected
Component(s)
Disconnect
Here
To Connected
Component(s)
RF1RF2
Antenna
3
Upgrading New TracVision Systems
If you are installing the Tri-Sat AutoSwitch Kit as
part of a new TracVision system installation, note
the following variations to the TracVision
Installation Guide.
• Only wire the receivers as specified in
these instructions
• Do not mount the switchplate until
you have finished installing the Tri-
Sat AutoSwitch Kit.
• Be sure to also wire the switchplate as
specified in the TracVision
Installation Guide.
Step 2 - Connect the Tri-Sat AutoSwitch Kit
This section explains how to connect the Tri-Sat
AutoSwitch Kit and a DIRECTV H21-200 or H20-
600 receiver.
NOTE: For information on wiring additional
components, refer to the Appendix on page 9.
a. Systems with a grounding block - Connect
the RF1 cable (A) from the grounding block’s
RF1 connection to the “From Antenna”
connector on the Tri-Sat AutoSwitch (see
Figure 3).
Systems without a grounding block -
Connect the antenna’s RF1 cable (A) to the
“From Antenna” connector on the Tri-Sat
AutoSwitch (see Figure 3).
Figure 3 Tri-Sat AutoSwitch Wiring Diagram
(A)
(B)
(C)
(D)
Standard
Receiver
(optional)
Antenna
RF1RF2
RJ22 Connector on
Back of Switchplate
TracVision Switchplate
DB9 Connector on
Front of Switchplate
Previously Installed
TracVision Systems
From Antenna
To DIRECTV HD
Receiver Coax
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
Satellite In
USB
Grounding
Block
Vehicle
AC Ground
Control Output
To DIRECTV HD
Receiver USB
New TracVision Systems
4
b. Connect the appropriate data cable (B) for
your installation type (see Figure 3 on page 3)
from the switchplate to the “Control Output”
connector on the Tri-Sat AutoSwitch.
NOTE: Switchplate wiring varies according to
installation type. The kit contains multiple data cables
to accommodate several TracVision products and
configurations. Refer to the Contents List for data
cable photos and part numbers.
If you are installing an Tri-Sat AutoSwitch
Kit to upgrade a TracVision system that is
already installed on a vehicle, be sure to use
the RJ22-to-DB9 data cable (KVH Part #32-
0916-25) supplied in the kit. You will connect
the DB9 end of the cable to the front of the
TracVision switchplate (see Figure 3 on
page 3).
If you are installing an Tri-Sat AutoSwitch
Kit as part of a new TracVision system
installation, be sure to use the RJ22-to-RJ22
data cable (KVH Part #32-0724-25) supplied
in the kit. You will connect to the RJ22
connector on the back of the TracVision
switchplate (see Figure 3 on page 3).
c. Connect one end of a coaxial cable (C) to the
“To DIRECTV HD Receiver Coax” connector
on the Tri-Sat AutoSwitch. Connect the other
end to the “Satellite In” connector on the
DIRECTV H21-200 or H20-600 receiver.
d. Connect one end of the USB cable (D) to the
“To DIRECTV HD Receiver USB” connector
on the Tri-Sat AutoSwitch. Connect the other
end of the cable to the “USB” connector on
the DIRECTV H21-200 or H20-600 receiver.
5
Receiver Installation
Be sure to follow these guidelines when installing
the receiver.
• The Tri-Sat AutoSwitch Kit is
compatible only with DIRECTV
model H21 receivers that have
manufacturer ID 200 and DIRECTV
model H20 receivers that have
manufacturer ID 600.
• The DIRECTV H21-200 or H20-600
receiver must be configured as an
“Oval, 3, LNB” dish type. Refer to the
receiver manual for configuration
instructions.
• Upon startup, the receiver might take
up to 30 minutes or more to fully load
the program guide for all three
DIRECTV satellites. Be sure to only
select channels carried on the 101
satellite until the program guide is
fully loaded.
Step 3 - Check for Flash Wizard Updates
You need to check for flash file updates to ensure
you have the most current software available (see
Figure 4). Follow the Flash Update Wizard’s
onscreen instructions to check for updates. This
procedure requires a PC with the latest version of
the KVH Flash Update Wizard installed and an
Internet connection.
NOTE: Refer to the Flash Update Wizard’s Help file
for details on checking for updates.
Step 4 - Flash the Main and RF Boards
Connect a PC to the RF port on your TracVision
system, as described in the Flash Update
Wizard’s Help file. Then follow the Flash Update
Wizard’s onscreen instructions to flash the
antenna’s main board and RF board.
NOTE: Refer to the Flash Update Wizard’s Help file
for details on flashing the antenna.
Figure 4 Check for Updates Option
6
Using the Tri-Sat AutoSwitch
This section explains how to operate the
TracVision system with the Tri-Sat AutoSwitch
installed.
Switching Satellites
When the Tri-Sat AutoSwitch is coupled with a
DIRECTV H21-200 or DIRECTV H20-600
receiver, the antenna automatically switches
among the Ku-band portion of the DIRECTV 101,
110, and 119 satellites as the user changes
channels using the receiver’s remote control.
NOTE: The receiver might take up to 30 seconds to
display video when changing channels, switching
between satellites, and/or switching between
standard-definition and high-definition channels.
TIP: For your convenience, KVH lists the DIRECTV
Ku-band HDTV channels, and the DIRECTV
satellites that carry them, on the web at
www.kvh.com/HDTV. Since DIRECTV changes its
channel lineups frequently, KVH can e-mail updates
to you whenever the HDTV lineup changes. Register
for this free service when you visit the website for the
first time.
7
Using the Tri-Sat AutoSwitch Kit with Multiple
Receivers
Since the antenna can only track one satellite at a
time, all receivers can only view channels carried
by the currently tracked satellite. Therefore,
switching channels on one Tri-Sat AutoSwitch-
equipped receiver might cause televisions
connected to other receivers to display different
programming, no programming, or an error
message. TV viewers can simply change the
channel until they select a channel carried by the
new satellite, or they can use any Tri-Sat
AutoSwitch-equipped receiver to switch back to
the original satellite.
NOTE: Only Tri-Sat AutoSwitch-equipped
DIRECTV H21-200 and H20-600 receivers control
satellite selection. Other receiver models and
additional DIRECTV H21-200 and H20-600
receivers without a mated Tri-Sat AutoSwitch cannot
control satellite selection, but they can change
channels on the currently selected satellite.
Using the Tri-Sat AutoSwitch Kit with Additional Tri-
Sat AutoSwitch-equipped DIRECTV H21-200 or H20-
600 Receivers
The Tri-Sat AutoSwitch enables automatic
satellite switching for one DIRECTV H21-200 or
H20-600 receiver. However, when two or more
Tri-Sat AutoSwitches are installed, any Tri-Sat
AutoSwitch-equipped receiver can control
satellite selection. The last Tri-Sat AutoSwitch-
equipped receiver to change satellites controls
satellite selection until another Tri-Sat
AutoSwitch-equipped receiver changes satellites.
9
Appendix
A standard wiring diagram is provided in Figure 3 on page 3. However, if you need to wire
additional components, refer to the table below to determine the appropriate wiring diagram
for your configuration.
NOTE: If you need to wire additional components not supported in the following diagrams, please contact
KVH Technical Support.
NOTE: If the TracVision system is not equipped with a grounding block (see Figure 1 and Figure 2 on
page 2), simply bypass the grounding block connections shown in the following diagrams when
connecting components.
To Install: Refer to:
Tri-Sat AutoSwitch Kit, 1 DIRECTV H21-200 or H20-
600 Receiver, 1 DVR, and 0 or 1 Additional Receivers
Page 10
Tri-Sat AutoSwitch Kit, 1 DIRECTV H21-200 or H20-
600 Receiver, and 2 or 3 Additional Receivers
Page 11
Tri-Sat AutoSwitch Kit, 2 DIRECTV H21-200 or H20-
600 Receivers, and 1 Additional Tri-Sat AutoSwitch
Page 12
Tri-Sat AutoSwitch Kit, 2 DIRECTV H21-200 or H20-
600 Receivers, 1 Additional Tri-Sat AutoSwitch, and 1
or 2 Additional Receivers
Page 13
Tri-Sat AutoSwitch Kit, 2 DIRECTV H21-200 or H20-
600 Receivers, 1 Additional Tri-Sat AutoSwitch, and 1
DVR
Page 14
10
Tri-Sat AutoSwitch Kit, 1 DIRECTV H21-200/
H20-600 Receiver, and 2 or 3 Additional
Receivers
Antenna
RF1
RF2
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
From Antenna
RJ22 Connector on
Back of Switchplate
TracVision Switchplate
DB9 Connector on
Front of Switchplate
New TracVision
Systems
Previously Installed
TracVision Systems
Grounding
Block
Vehicle
AC Ground
To DIRECTV HD
Receiver Coax
13V
13V
SAT
Rx4
ANT
IN
Rx3
DC
20V
Rx2
Rx1
18V
SAT
Power
Supply
MultiSwitch
Rx3
Rx1
Rx2
18V
Rx4
Receivers, HD or Standard
(or terminate with 75 ohm blocks)
To DIRECTV HD
Receiver USB
This receiver controls
satellite selection
11
Tri-Sat AutoSwitch Kit, 1 DIRECTV H21-200/
H20-600 Receiver, 1 DVR, and 0
or 1 Additional Receivers
Antenna
RF1
RF2
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
From Antenna
RJ22 Connector on
Back of Switchplate
TracVision Switchplate
DB9 Connector on
Front of Switchplate
New TracVision
Systems
Previously Installed
TracVision Systems
Grounding
Block
Vehicle
AC Ground
To DIRECTV HD
Receiver Coax
To DIRECTV HD
Receiver USB
Receiver, HD or Standard
(or terminate with 75 ohm blocks)
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
DVR, HD or Standard
Satellite In
2
Satellite In
1 (FTM)
13V
13V
SAT
Rx4
ANT
IN
Rx3
DC
20V
Rx2
Rx1
18V
SAT
Power
Supply
MultiSwitch
Rx3
Rx1
Rx2
18V
Rx4
This receiver controls
satellite selection
12
Tri-Sat AutoSwitch Kit, 2 DIRECTV H21-200/
H20-600 Receivers, and 1 Additional Tri-Sat
AutoSwitch
Antenna
RF1
RF2
Control Output
RJ22 Connector on
Back of Switchplate
TracVision Switchplate
DB9 Connector on
Front of Switchplate
New TracVision
Systems
Previously Installed
TracVision Systems
From Antenna
Grounding
Block
Vehicle
AC Ground
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
To DIRECTV HD
Receiver Coax
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
To DIRECTV HD
Receiver USB
From Antenna
To DIRECTV HD
Receiver Coax
Control Input
To DIRECTV HD
Receiver USB
13
Tri-Sat AutoSwitch Kit, 2 DIRECTV H21-200/
H20-600 Receivers, 1 Additional Tri-Sat
AutoSwitch, and 1 or 2 Additional Receivers
Receivers, HD or Standard
(or terminate with 75 ohm blocks)
Antenna
RF1 RF2
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
Control Input
From Antenna
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
RJ22 Connector on
Back of Switchplate
TracVision Switchplate
DB9 Connector on
Front of Switchplate
New TracVision
Systems
Previously Installed
TracVision Systems
To DIRECTV HD
Receiver USB
Vehicle
AC Ground
Grounding
Block
To DIRECTV HD
Receiver Coax
13V
13V
SAT
Rx4
ANT
IN
Rx3
DC
20V
Rx2
Rx1
18V
SAT
Power
Supply
MultiSwitch
Rx3
Rx1
Rx2
18V
Rx4
14
Tri-Sat AutoSwitch Kit, 2 DIRECTV H21-200/
H20-600 Receivers, 1 Additional Tri-Sat
AutoSwitch, and 1 DVR
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
DVR, HD or Standard
Satellite In
2
Satellite In
1 (FTM)
Antenna
RF1 RF2
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
Control Input
From Antenna
Control Output
USB
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VIDEO OUT
CAUTION
OFF-AIR IN SATELLITE IN
DIGITAL AUDIO
OUT OPTICAL
HDMI OUT
PHONE JACK
RF REMOTE
ANTENNA
AC 120V, 60 Hz
H21-200/H20-600 Receiver
Satellite In
USB
RJ22 Connector on
Back of Switchplate
TracVision Switchplate
DB9 Connector on
Front of Switchplate
New TracVision
Systems
Previously Installed
TracVision Systems
To DIRECTV HD
Receiver USB
Vehicle
AC Ground
Grounding
Block
To DIRECTV HD
Receiver Coax
13V
13V
SAT
Rx4
ANT
IN
Rx3
DC
20V
Rx2
Rx1
18V
SAT
Power
Supply
MultiSwitch
Rx3
Rx1
Rx2
18V
Rx4
To DIRECTV HD
Receiver USB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

KVH Industries TracVision R4SL Installation And Operation Instructions Manual

KVH Industries
Brand
KVH Industries
Model
TracVision R4SL
Type
Installation And Operation Instructions Manual
This manual is also suitable for

KVH Industries TracVision R4SL is a satellite TV system designed for recreational vehicles, allowing you to enjoy your favorite shows and movies on the go. With automatic satellite acquisition and tracking, you can easily access channels from DISH Network, DIRECTV, and Bell TV, including popular HD channels. The R4SL features a compact, low-profile dome antenna for easy installation on your RV's roof, and it works seamlessly with your existing TV and receiver.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents