King Canada 8045LK-BC User manual

Brand: King Canada

Model: 8045LK-BC

Category: Power tools

Type: User manual

INSTRUCTION MANUAL

MODEL: 8045LK-BC

20V

MAX

LITHIUM-ION

CORDLESS

HAMMER

DRILL

KIT

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS 20V HAMMER DRILL

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and

durability standards. King Canada warrants to the original retail consumer a 2-year

limited warranty as of the date the product was purchased at retail and that each

product is free from defects in materials. Warranty does not apply to defects due

directly or indirectly to misuse, abuse, normal wear and tear, negligence or

accidents, repairs done by an unauthorized service center, alterations and lack of

maintenance. King Canada shall in no event be liable for death, injuries to persons

or property or for incidental, special or consequential damages arising from the use

of our products.

To take advantage of this limited warranty, return the product at your expense

together with your dated proof of purchase to an authorized King Canada service

center. Contact your retailer or visit our web site at www.kingcanada.com for an

updated listing of our authorized service centers. In cooperation with our authorized

service center, King Canada will either repair or replace the product if any part or

parts covered under this warranty which examination proves to be defective in

workmanship or material during the warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and

references are subject to change without prior notice.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

1. KNOW YOUR TOOL

Read and understand the instruction manual and labels affixed to the tool. Learn its

application and limitations as well as its specific potential hazards.

2. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area

well lit and provide adequate surrounding work space.

3. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was not designed.

4. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could

get caught in moving parts. Non-slip footwear is recommended. Wear protective hair

covering to contain long hair. Roll up long sleeves above the elbows.

5. MAINTAIN TOOL WITH CARE.

Keep tool clean for best and safest performance. Follow instructions for operation and

changing accessories.

6. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

7. AVOID ACCIDENTAL STARTING.

Make sure the switch is in the ‘’OFF’’ position before connecting battery.

8. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the instructions that

accompany the accessories. The use of improper accessories may cause hazards.

9. CHECK FOR DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are damaged should be

carefully checked to ensure they will operate properly and perform their intended

function. Check for alignment of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A guard or other parts which are damaged

should be properly repaired or replaced.

Specific Safety Instructions

1. Only use King attachments and accessories, serious injury can result if this warning is

not respected.

2. Before installing or changing an accessory, remove the battery from the tool.

3. Hold power tool by insulated grip surface, an accessory could contact hidden wiring,

contact with a “live” wire will make exposed metal surfaces “live” and will shock the

operator.

4. Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

stoves and refrigerators. Risk of electric shock if your body is grounded.

5. Use clamps or any other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

loss of control.

6. Wear protective gloves and safety glasses, an accessory can become extremely hot

during operation, danger of burns!

7. Do not use the tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

GENERAL & SPECIFIC

SAFETY INSTRUCTIONS

LITHIUM-ION BATTERY &

CHARGER INFORMATION

WARNING: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built into this

product, but must be supplied by the operator. Do not plug in charger or install battery into

saw until you have read and understood this instruction manual.

Available batteries and charger for this 20V max Li-ion for Hammer Drill:

• 1.5 Ah 20V max Lithium-ion battery (Model K-020LBT)

• 3.0 Ah 20V max Lithium-ion battery (Model K-023LBT-3)

• 20V max Lithium-ion battery charger (Model K-020LCG)

Charging any other battery may damage the charger and possibly cause serious injury.

Battery and Charger Safety Precautions

1) Do not store or carry battery in a way which metal objects could contact the exposed

metal end of the battery. The battery could short-circuit causing a fire, personal injury

and damage to the battery.

2) Never attempt to open the battery for any reason. If battery housing has cracked,

discontinue use immediately and do not try to recharge it. Dispose of battery.

3) Never charge a wet battery or a battery that shows signs of corrosion.

4) Do not use an extension cord with the charger, plug charger directly into a 120V AC

receptacle.

5) Do not use charger if power cord is damaged, replace damaged cord or charger.

6) Do not charge battery when work area or the battery temperature is or below 0

C or

above 45

7) Unplug charger when not in use.

8) It is important to recycle or dispose of battery properly at your nearest battery

recycling location.

9) The contents of the battery is slightly acidic, do not incinerate the battery, it can

explode in a fire.

10) A small leakage from the battery may occur under extreme usage, charging or

temperature conditions. This does not indicate a battery failure. However, if the battery

housing is cracked and leakage gets on your skin, follow these steps;

-Wash with soap immediately.

-Neutralize area with mild acid such as vinegar or lemon juice.

-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then

seek medical attention.

Lithium-ion Battery

Lithium-ion batteries do not have a memory and do not require to be completely

discharged periodically. After use, charge battery so that it is fully charged for the next time

you use this tool. A fully charged battery will only loose about 2% of its charge per month

during storage.

GETTING TO KNOW YOUR TOOL

SPECIFICATIONS

Model................................................................................................................8045LK-BC

Voltage ................................................................................................................20V MAX

Speeds (RPM) ........................................................................................2 (0-300/0-1,000)

Capacities (Concrete/Steel/Wood) ..............................................................7/8”, 3/8”, 7/8”

Weight ........................................................................................................................4 lbs

Battery type ..................................................................................1.5Ah (Mod. K-020LBT)

Battery charger ........................................................................................Mod. K-020LCG

Figure 1

1. 360

control handle

2. SDS+ chuck

3. Depth stop mount

4. Depth stop adj. button

5. Drill/hammer selector

6. Speed range selector

7. Battery/rotation indicator

8. Battery indicator button

9. Forward/reverse/lock

10. Variable speed trigger

11. Battery compartment

12. SDS+ 3/8” keyless chuck

13. Depth stop rod

14. 4 SDS+ drill bits

15. 1.5 Ah battery

16. Charger

17. Carry bag

Unpacking your Hammer Drill Kit

Your cordless Hammer Drill requires minimal assembly before use, remove all contents

from the box. Inspect the tool carefully to make sure no breakage or damage has occurred

during transport. If any parts are missing, do not attempt to use the tool until you have

obtained the missing parts from your King Canada retailer.

Contents:

1- Cordless Hammer Drill

4- SDS+ Drill bits

1- SDS+ 3/8” keyless chuck

1- Depth stop rod

OPERATION

USING YOUR 20V MAX LITHIUM-ION CORDLESS

HAMMER DRILL KIT

WARNING: Do not install battery until the accessory is

installed securely to the tool. Wear protective gloves

and safety glasses, an accessory can become extremely

hot during operation, danger of burns!

Charging the battery/battery level indicator

20V max Li-ion batteries come with a battery power level

indicator (A) Fig.2, press the button (B) to see the charge

level. If the battery level is low charge the battery. To

charge the battery (C) Fig.2, plug charger (D) power cord

into a 120V AC receptacle (do not use extension cord).

The red LED (F) will light up to indicate power to the

charger. Align the grooves the battery with those of the

charger and slide the battery all the way until it snaps into

place. The green LED (E) will flash indicating the

charging procedure has begun. Once the green LED (E)

stops flashing, the battery is fully charged and ready to

use. Press the battery clip (B) Fig.3 to remove battery

from charger.

Installing/removing battery from drill

To install a battery (A) Fig.3 to the base of the cordless

Hammer Drill, align the grooves of the battery with those

of the base and slide the battery all the way until the

battery clip (B) snaps and holds the battery into place.

To remove the battery from the base, press the battery

clip (B) Fig.3 and slide the battery away from the base.

Turning Tool On/Off

To turn your hammer Drill ON, press the trigger (A) Fig.4.

Release the trigger to turn your Hammer Drill OFF.

Forward/Reverse/Lock switch

Warning! This tool must be stopped before the fwd/rev

switch (B) Fig.4 can be used. Otherwise you could

damage the tool. The fwd/rev switch (B) is used to switch

between right and left rotation. When the switch is in the middle position the trigger (A) is

locked and cannot be pressed. To avoid accidental starts, always set the fwd/rev switch in

the middle position.

Figure 2

Figure 3

Figure 4

OPERATION

Battery Level Indicator & Rotation Indicator

This Hammer Drill comes with a battery level indicator

(A) Fig.5. Press the indicator button (B) to see the

remaining battery charge. If the battery level is low, only

the red indicator light will come on, all three indicator

lights come on when the battery is fully charged.

During use (while holding the trigger), the same indicator

lights will indicate the direction of rotation of the chuck.

The blue indicator light symbolizes forward rotation, the

red indicator light symbolizes reverse rotation.

Selecting Drilling or Hammer Mode

Drilling and screwing- Press the small button (A) Fig.6

and turn the mode selector switch (B) to the “Drilling”

symbol (towards the left).

Hammer drilling- Press the small button (A) Fig.6 and

turn the mode selector switch (B) to the “Hammer”

symbol (towards the right as shown in Fig.6). The mode

selector can also be used when the motor is running.

Installing/Removing SDS+ Drill Bits or SDS+ 3/8”

Keyless Chuck

• DISCONNECT BATTERY FROM TOOL BASE.

This Hammer Drill Kit comes with 4 SDS+ Drill bits and a

SDS+ 3/8” keyless chuck which allows you to install and

use standard drill bits (not included).

1) To secure an SDS+ drill bit or the SDS+ 3/8” keyless

chuck, insert the SDS+ mounting shaft (A) Fig.7

(SDS+ drill bit or the keyless chuck) of the accessory

into the SDS+ chuck (B), push it into the chuck until it

locks inside the chuck. It may be necessary to turn the

SDS+ mounting shaft before it can be fully inserted

into the SDS+ chuck.

2) To remove SDS+ accessory, pull back on the chuck

(A) Fig.8 as shown and slide the SDS+ accessory (B)

out of the chuck.

Securing Workpiece

Use clamps or any other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control and injury.

Figure 5

Figure 6

Figure 7

Figure 8

OPERATION

Selecting Speed Range

This Hammer Drill comes with 2 speed ranges, a LOW

(0-300 RPM) and HI (0-1000 RPM) speed range. Move

the speed range selector (A) Fig.9 towards the front of

the tool for LOW speed range, or move the speed range

selector towards the back of the tool for HI speed range.

Important: The speed range can only be changed while

to tool is stopped and not in use.

Adjusting the 360

Control Handle

The control handle (A) Fig.10 can be positioned at any

position which is most comfortable for the user. Turn the

handle counterclockwise to loosen it. Reposition the

handle in the desired position and retighten handle.

Using the Depth Stop Rod

A depth stop rod (A) Fig. 11 is included, it is used for

repetitious drilling at a pre-set depth. To install the depth

stop rod, press and hold the depth stop adjustment

button (B). Then insert the depth stop rod into the rod

support (C), release the depth stop adjustment button to

secure the depth stop rod.

Working materials

The working materials should be within: “wood, metal,

resin boards, concrete”.

• When drilling hard, smooth surfaces, use a center

punch to mark the desired hole location. This will

prevent the drill from slipping off center as the hole is

started.

• The working material should be secured in a device or with clamps to keep it from moving

as the drill bit rotates.

• When drilling concrete and masonry, move the mode selector switch (B) Fig.6 to the

“percussion icon” (right) to achieve the maximum impact when drilling into maconry.

Installing Standard Drill Bit into SDS+ 3/8” Keyless Chuck

• Clean the shivers and any other foreign objects away from the bit and chuck, otherwise

the bit might not be tightened securely and thus will induce severe personal injuries.

• Open the chuck jaws by turning the chuck sleeve counterclockwise.

• Insert the desired drill bit into the chuck, make sure that the bit is in as far as it will go.

• Tighten all three jaws of the chuck by rotating the chuck sleeve clockwise.

Figure 9

Figure 10

Figure 11

MAINTENANCE

WARNING: THERE ARE NO USER SERVICE-ABLE PARTS INSIDE

Preventative maintance performed by an unauthorized personnel may result in the

misplacement of internal wires and componenets which could cause serious hazards. We

recommend that all servicing be performed by a qualified KING CANADA service centre

technician.

Battery

Pay attention to the battery power levels as the battery nears its end of life. If you notice a

decrease in battery performance or a significant difference in running power between

charges, then it is time to replace the battery. Failure to do so may damage the charger

and cause improper operation.

Cleaning

To avoid accidents, always remove the battery from the tool before cleaning. The tool is

most effectively cleaned with the use of an air compressor. Always wear safety glasses

when using an air compressor. Ventilation openings and switch levers must be kept clean

and free of foreign objects. Do not insert pointed objects through these openings in the

attempt to clean them.

1. Air vents of the tool should be cleaned regularly to avoid overheating of the motor which

is caused by the blocking of the air vents.

2. DON’T clean this tool with water, as no liquid is allowed in the tool body. Clean the tool

with a dry clean cloth only. Compressed air at low pressure is also suitable.

3. DON’T allow petroleum based products to come into contact with the plastic parts of the

tool, as they contain chemicals that can damage or destroy the plastic parts.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram

and parts list.

King Canada 8045LK-BC User manual

Brand: King Canada

Model: 8045LK-BC

Category: Power tools

Type: User manual

Download PDF

report

King Canada 8045LK-BC User manual

King Canada 8045LK-BC User manual

Related papers

Other documents