King Canada 8045LK-BC User manual

Category
Power tools
Type
User manual
COPYRIGHT © 2020 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
INSTRUCTION MANUAL
MODEL: 8045LK-BC
20V
MAX
LITHIUM-ION
CORDLESS
HAMMER
DRILL
KIT
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS 20V HAMMER DRILL
KING CANADA TOOLS
OFFERS A 2-YEAR LIMITED WARRANTY
FOR NON-COMMERCIAL USE.
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and
durability standards. King Canada warrants to the original retail consumer a 2-year
limited warranty as of the date the product was purchased at retail and that each
product is free from defects in materials. Warranty does not apply to defects due
directly or indirectly to misuse, abuse, normal wear and tear, negligence or
accidents, repairs done by an unauthorized service center, alterations and lack of
maintenance. King Canada shall in no event be liable for death, injuries to persons
or property or for incidental, special or consequential damages arising from the use
of our products.
To take advantage of this limited warranty, return the product at your expense
together with your dated proof of purchase to an authorized King Canada service
center. Contact your retailer or visit our web site at www.kingcanada.com for an
updated listing of our authorized service centers. In cooperation with our authorized
service center, King Canada will either repair or replace the product if any part or
parts covered under this warranty which examination proves to be defective in
workmanship or material during the warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and
references are subject to change without prior notice.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
1. KNOW YOUR TOOL
Read and understand the instruction manual and labels affixed to the tool. Learn its
application and limitations as well as its specific potential hazards.
2. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area
well lit and provide adequate surrounding work space.
3. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was not designed.
4. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could
get caught in moving parts. Non-slip footwear is recommended. Wear protective hair
covering to contain long hair. Roll up long sleeves above the elbows.
5. MAINTAIN TOOL WITH CARE.
Keep tool clean for best and safest performance. Follow instructions for operation and
changing accessories.
6. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
7. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before connecting battery.
8. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the instructions that
accompany the accessories. The use of improper accessories may cause hazards.
9. CHECK FOR DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be
carefully checked to ensure they will operate properly and perform their intended
function. Check for alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other parts which are damaged
should be properly repaired or replaced.
Specific Safety Instructions
1. Only use King attachments and accessories, serious injury can result if this warning is
not respected.
2. Before installing or changing an accessory, remove the battery from the tool.
3. Hold power tool by insulated grip surface, an accessory could contact hidden wiring,
contact with a “live” wire will make exposed metal surfaces “live” and will shock the
operator.
4. Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
stoves and refrigerators. Risk of electric shock if your body is grounded.
5. Use clamps or any other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to
loss of control.
6. Wear protective gloves and safety glasses, an accessory can become extremely hot
during operation, danger of burns!
7. Do not use the tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
LITHIUM-ION BATTERY &
CHARGER INFORMATION
WARNING: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator. Do not plug in charger or install battery into
saw until you have read and understood this instruction manual.
Available batteries and charger for this 20V max Li-ion for Hammer Drill:
• 1.5 Ah 20V max Lithium-ion battery (Model K-020LBT)
• 3.0 Ah 20V max Lithium-ion battery (Model K-023LBT-3)
• 20V max Lithium-ion battery charger (Model K-020LCG)
Charging any other battery may damage the charger and possibly cause serious injury.
Battery and Charger Safety Precautions
1) Do not store or carry battery in a way which metal objects could contact the exposed
metal end of the battery. The battery could short-circuit causing a fire, personal injury
and damage to the battery.
2) Never attempt to open the battery for any reason. If battery housing has cracked,
discontinue use immediately and do not try to recharge it. Dispose of battery.
3) Never charge a wet battery or a battery that shows signs of corrosion.
4) Do not use an extension cord with the charger, plug charger directly into a 120V AC
receptacle.
5) Do not use charger if power cord is damaged, replace damaged cord or charger.
6) Do not charge battery when work area or the battery temperature is or below 0
0
C or
above 45
0
C.
7) Unplug charger when not in use.
8) It is important to recycle or dispose of battery properly at your nearest battery
recycling location.
9) The contents of the battery is slightly acidic, do not incinerate the battery, it can
explode in a fire.
10) A small leakage from the battery may occur under extreme usage, charging or
temperature conditions. This does not indicate a battery failure. However, if the battery
housing is cracked and leakage gets on your skin, follow these steps;
-Wash with soap immediately.
-Neutralize area with mild acid such as vinegar or lemon juice.
-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then
seek medical attention.
Lithium-ion Battery
Lithium-ion batteries do not have a memory and do not require to be completely
discharged periodically. After use, charge battery so that it is fully charged for the next time
you use this tool. A fully charged battery will only loose about 2% of its charge per month
during storage.
GETTING TO KNOW YOUR TOOL
SPECIFICATIONS
Model................................................................................................................8045LK-BC
Voltage ................................................................................................................20V MAX
Speeds (RPM) ........................................................................................2 (0-300/0-1,000)
Capacities (Concrete/Steel/Wood) ..............................................................7/8”, 3/8”, 7/8”
Weight ........................................................................................................................4 lbs
Battery type ..................................................................................1.5Ah (Mod. K-020LBT)
Battery charger ........................................................................................Mod. K-020LCG
Figure 1
1. 360
0
control handle
2. SDS+ chuck
3. Depth stop mount
4. Depth stop adj. button
5. Drill/hammer selector
6. Speed range selector
7. Battery/rotation indicator
8. Battery indicator button
9. Forward/reverse/lock
10. Variable speed trigger
11. Battery compartment
12. SDS+ 3/8” keyless chuck
13. Depth stop rod
14. 4 SDS+ drill bits
15. 1.5 Ah battery
16. Charger
17. Carry bag
Unpacking your Hammer Drill Kit
Your cordless Hammer Drill requires minimal assembly before use, remove all contents
from the box. Inspect the tool carefully to make sure no breakage or damage has occurred
during transport. If any parts are missing, do not attempt to use the tool until you have
obtained the missing parts from your King Canada retailer.
Contents:
1- Cordless Hammer Drill
4- SDS+ Drill bits
1- SDS+ 3/8” keyless chuck
1- Depth stop rod
OPERATION
USING YOUR 20V MAX LITHIUM-ION CORDLESS
HAMMER DRILL KIT
WARNING: Do not install battery until the accessory is
installed securely to the tool. Wear protective gloves
and safety glasses, an accessory can become extremely
hot during operation, danger of burns!
Charging the battery/battery level indicator
20V max Li-ion batteries come with a battery power level
indicator (A) Fig.2, press the button (B) to see the charge
level. If the battery level is low charge the battery. To
charge the battery (C) Fig.2, plug charger (D) power cord
into a 120V AC receptacle (do not use extension cord).
The red LED (F) will light up to indicate power to the
charger. Align the grooves the battery with those of the
charger and slide the battery all the way until it snaps into
place. The green LED (E) will flash indicating the
charging procedure has begun. Once the green LED (E)
stops flashing, the battery is fully charged and ready to
use. Press the battery clip (B) Fig.3 to remove battery
from charger.
Installing/removing battery from drill
To install a battery (A) Fig.3 to the base of the cordless
Hammer Drill, align the grooves of the battery with those
of the base and slide the battery all the way until the
battery clip (B) snaps and holds the battery into place.
To remove the battery from the base, press the battery
clip (B) Fig.3 and slide the battery away from the base.
Turning Tool On/Off
To turn your hammer Drill ON, press the trigger (A) Fig.4.
Release the trigger to turn your Hammer Drill OFF.
Forward/Reverse/Lock switch
Warning! This tool must be stopped before the fwd/rev
switch (B) Fig.4 can be used. Otherwise you could
damage the tool. The fwd/rev switch (B) is used to switch
between right and left rotation. When the switch is in the middle position the trigger (A) is
locked and cannot be pressed. To avoid accidental starts, always set the fwd/rev switch in
the middle position.
Figure 2
Figure 3
Figure 4
OPERATION
Battery Level Indicator & Rotation Indicator
This Hammer Drill comes with a battery level indicator
(A) Fig.5. Press the indicator button (B) to see the
remaining battery charge. If the battery level is low, only
the red indicator light will come on, all three indicator
lights come on when the battery is fully charged.
During use (while holding the trigger), the same indicator
lights will indicate the direction of rotation of the chuck.
The blue indicator light symbolizes forward rotation, the
red indicator light symbolizes reverse rotation.
Selecting Drilling or Hammer Mode
Drilling and screwing- Press the small button (A) Fig.6
and turn the mode selector switch (B) to the “Drilling”
symbol (towards the left).
Hammer drilling- Press the small button (A) Fig.6 and
turn the mode selector switch (B) to the “Hammer”
symbol (towards the right as shown in Fig.6). The mode
selector can also be used when the motor is running.
Installing/Removing SDS+ Drill Bits or SDS+ 3/8”
Keyless Chuck
• DISCONNECT BATTERY FROM TOOL BASE.
This Hammer Drill Kit comes with 4 SDS+ Drill bits and a
SDS+ 3/8” keyless chuck which allows you to install and
use standard drill bits (not included).
1) To secure an SDS+ drill bit or the SDS+ 3/8” keyless
chuck, insert the SDS+ mounting shaft (A) Fig.7
(SDS+ drill bit or the keyless chuck) of the accessory
into the SDS+ chuck (B), push it into the chuck until it
locks inside the chuck. It may be necessary to turn the
SDS+ mounting shaft before it can be fully inserted
into the SDS+ chuck.
2) To remove SDS+ accessory, pull back on the chuck
(A) Fig.8 as shown and slide the SDS+ accessory (B)
out of the chuck.
Securing Workpiece
Use clamps or any other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss
of control and injury.
Figure 5
Figure 6
Figure 7
Figure 8
OPERATION
Selecting Speed Range
This Hammer Drill comes with 2 speed ranges, a LOW
(0-300 RPM) and HI (0-1000 RPM) speed range. Move
the speed range selector (A) Fig.9 towards the front of
the tool for LOW speed range, or move the speed range
selector towards the back of the tool for HI speed range.
Important: The speed range can only be changed while
to tool is stopped and not in use.
Adjusting the 360
0
Control Handle
The control handle (A) Fig.10 can be positioned at any
position which is most comfortable for the user. Turn the
handle counterclockwise to loosen it. Reposition the
handle in the desired position and retighten handle.
Using the Depth Stop Rod
A depth stop rod (A) Fig. 11 is included, it is used for
repetitious drilling at a pre-set depth. To install the depth
stop rod, press and hold the depth stop adjustment
button (B). Then insert the depth stop rod into the rod
support (C), release the depth stop adjustment button to
secure the depth stop rod.
Working materials
The working materials should be within: “wood, metal,
resin boards, concrete”.
• When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill from slipping off center as the hole is
started.
• The working material should be secured in a device or with clamps to keep it from moving
as the drill bit rotates.
• When drilling concrete and masonry, move the mode selector switch (B) Fig.6 to the
“percussion icon” (right) to achieve the maximum impact when drilling into maconry.
Installing Standard Drill Bit into SDS+ 3/8” Keyless Chuck
• Clean the shivers and any other foreign objects away from the bit and chuck, otherwise
the bit might not be tightened securely and thus will induce severe personal injuries.
• Open the chuck jaws by turning the chuck sleeve counterclockwise.
• Insert the desired drill bit into the chuck, make sure that the bit is in as far as it will go.
• Tighten all three jaws of the chuck by rotating the chuck sleeve clockwise.
Figure 9
Figure 10
Figure 11
MAINTENANCE
MAINTENANCE
WARNING: THERE ARE NO USER SERVICE-ABLE PARTS INSIDE
Preventative maintance performed by an unauthorized personnel may result in the
misplacement of internal wires and componenets which could cause serious hazards. We
recommend that all servicing be performed by a qualified KING CANADA service centre
technician.
Battery
Pay attention to the battery power levels as the battery nears its end of life. If you notice a
decrease in battery performance or a significant difference in running power between
charges, then it is time to replace the battery. Failure to do so may damage the charger
and cause improper operation.
Cleaning
To avoid accidents, always remove the battery from the tool before cleaning. The tool is
most effectively cleaned with the use of an air compressor. Always wear safety glasses
when using an air compressor. Ventilation openings and switch levers must be kept clean
and free of foreign objects. Do not insert pointed objects through these openings in the
attempt to clean them.
1. Air vents of the tool should be cleaned regularly to avoid overheating of the motor which
is caused by the blocking of the air vents.
2. DON’T clean this tool with water, as no liquid is allowed in the tool body. Clean the tool
with a dry clean cloth only. Compressed air at low pressure is also suitable.
3. DON’T allow petroleum based products to come into contact with the plastic parts of the
tool, as they contain chemicals that can damage or destroy the plastic parts.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram
and parts list.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

King Canada 8045LK-BC User manual

Category
Power tools
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI