Vector 000 CANDLE POWER SPOTLIGHT Owner's Manual & Warranty Information

Type
Owner's Manual & Warranty Information

This manual is also suitable for

Vector 000 CANDLE POWER SPOTLIGHT is a compact, durable and portable system that features:

  • A powerful halogen beam spotlight, ideal for illuminating large areas or objects at a distance.
  • A very efficient LED area light, perfect for providing diffused lighting in smaller spaces or for close-up work.
  • An emergency flashing red hazard light, which can be used to warn of potential hazards or to attract attention in case of an emergency.
  • A rubberized grip for easy portability and a rubberized base for stability.
  • A rugged carry case to protect the spotlight and tools during transport and storage.

Vector 000 CANDLE POWER SPOTLIGHT is a compact, durable and portable system that features:

  • A powerful halogen beam spotlight, ideal for illuminating large areas or objects at a distance.
  • A very efficient LED area light, perfect for providing diffused lighting in smaller spaces or for close-up work.
  • An emergency flashing red hazard light, which can be used to warn of potential hazards or to attract attention in case of an emergency.
  • A rubberized grip for easy portability and a rubberized base for stability.
  • A rugged carry case to protect the spotlight and tools during transport and storage.
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USING,
READ AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND
PRODUCT LABELS, PLUS ALL MANUFACTURERS’ GUIDELINES. FAILURE TO DO SO
COULD RESULT IN INJURY AND/OR PROPERTY DAMAGE.
4140 SW 28th Way, FT. LAUDERDALE, FL 33312
TEL 954-584-4446 TOLL FREE 866-584-5504 FAX 954-584-5556
www.vectormfg.com
VEC271MG
TOOL SET
Hammer
Phillips Screwdriver
Slotted Screwdriver
Slip-joint Pliers,
Hex Key Set
Adjustable Wrench
FEATURES
Powerful Halogen Beam Spotlight
Very Efficient Area Light
Red Flashing Hazard Light
12 Volt DC Power Cord
Rubberized Handle, Base and Bezel
Rugged Portable Carry Case
PORTABLE 1
,
000
,
000
CANDLE POWER SPOTLIGHT
AND TOOL KIT
OWNER’S MANUAL & WARRANTY INFORMATION
IMPORTANT SAFETY INFORMATION. SAVE THESE INSTRUCTIONS!
2
TABLE OF CONTENTS (VEC271MG)
1. SAFETY INFORMATION AND INSTRUCTIONS.................................................3
2. INTRODUCTION ............................................................................................4
3. OPERATION...................................................................................................4
3.1 Spotlight Operation...............................................................4
3.2 High Efficiency Area Light Operation .....................................5
3.3 Red Hazard Emergency Light Operation ................................5
4. VEC271MG DIAGRAM ..................................................................................5
5. REPLACEMENT PARTS ....................................................................................6
5.1 Halogen Spotlight Replacement.............................................6
5.2 Fuse Replacement Diagram ...................................................6
6. SPECIFICATIONS............................................................................................6
7. VECTOR ONE YEAR LIMITED WARRANTY PROGRAM .....................................7
3
1. SAFETY INFORMATION AND INSTRUCTIONS
The following symbols will be used throughout this manual.
The following safety precautions must be followed at all times along
with any additional existing safety rules.
1. Completely read this product manual as well as all manufacturers’
user manuals prior to usage of unit and/or tools.
2. Be thoroughly familiar with the proper use of the unit and/or tools.
3. Always plug 12 volt DC power cord into 12 volt DC accessory
power outlet only.
4. Never operate the unit near fire, flammable gas or liquid.
5. Never leave unit unattended while in use.
6. Never submerge this unit in water. When using the unit near water,
do not allow electrical cord to become damp, moist or wet as electrical
shock could result. Always protect the unit from rain, snow or other
sources of moisture.
7. Keep unit and/or tools out of reach of children and untrained
people (whether stored, or in use)!
8. All ON/OFF switches must be in the OFF position when the unit is
not in use. Make sure all switches are in the OFF position before
connection to a power source or load.
9. When using this unit, stand the unit on a flat, stable surface, and
be sure to keep all clamps, cords, clothing and body parts away from
moving components.
10. Hand tools must be used for proper application.
11. Proper protective eyewear (safety goggles) must be worn when
using hand tools. Tools may chip if struck with other objects of equal
hardness and could cause bodily injury if not used with extreme care.
12. Check unit periodically for wear and tear. Replace worn or
defective parts immediately. Contact Vector Customer Service at (954)
584-4446 or toll-free (866) 584-5504.
INDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICH, IF
NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.
INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF
NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY.
INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY
RESULT IN MINOR OR MODERATE INJURY.
INDICATES IMPORTANT INFORMATION THAT IF NOT FOLLOWED, MAY CAUSE
DAMAGE TO EQUIPMENT.
4
2. INTRODUCTION
Congratulations on selecting the VEC271MG Portable 1,000,000
Candle Power Spotlight and Tool Kit. This spotlight and tool kit will
provide years of reliable service if maintained properly.
The VEC271MG Portable 1,000,000 Candle Power Spotlight and Tool
Kit is a compact, durable and portable system that features:
•A powerful halogen beam spotlight,
•A very efficient LED area light,
An emergency flashing red hazard light,
•A reflector strip on the back of the unit,
•A rubberized grip for easy portability,
•A rubberized base for stability,
•A rugged carry case for tools,
•Practical tools needed for everyday repair jobs; hammer,
Phillips screwdriver, flathead screwdriver, hex key set, adjustable
wrench and slip joint pliers.
The VEC271MG Portable 1,000,000 Candle Power Spotlight and Tool
Kit can plug into any 12 volt DC accessory outlet in the car, camp,
garage, home, mini-van, SUV, trailer or truck.
Use the VEC271MG:
As an emergency hazard and/or spotlight for roadside
assistance,
For extra lighting while camping, fishing, or working,
•Ideal for small household, workshop and vehicle repairs.
3. OPERATION
3.1 SPOTLIGHT OPERATION
Make sure ON/OFF (3-position)
switch is in OFF position;
location is the center.
Remove the 12 volt DC power cord
and plug it into any 12 volt DC vehicle
accessory outlet.
Switch spotlight to the ON position; location is
closest to the spotlight.
•Place base on firm steady surface or hold rubberized handle
while using spotlight.
When finished with spotlight usage, place switch in OFF
position, location is the center.
Unplug 12 volt DC power accessory barrel from 12 volt DC
power source or vehicle accessory outlet.
Restore power cord into its compartment.
5
3.2 HIGH EFFICIENCY AREA LIGHT OPERATION
•Make sure ON/OFF (2-position) switch is in OFF position.
Remove the 12 volt DC power accessory cord and plug it into
any 12 volt DC vehicle accessory outlet.
Switch small switch located on area light to ON position.
•Place base on firm steady surface or hold rubberized handle
while using area light.
When finished with area light usage, place switch in OFF
position.
Unplug 12 volt DC accessory power cord from 12 volt DC
power port.
Restore power cord into its compartment.
3.3 RED HAZARD EMERGENCY LIGHT OPERATION
•Make sure ON/OFF (3-position) switch is in OFF position,
center.
Remove the 12 volt DC accessory power cord and plug it into
any 12 volt DC vehicle accessory outlet.
•Switch ON by pushing switch toward the back of the unit
where the emergency red LED hazard light is
located.
•Place base on firm steady surface or hold rubberized handle
while using red hazard emergency light.
When finished with red hazard emergency light usage, place
switch in OFF position, center.
Unplug 12 volt DC accessory
power cord from 12 volt DC vehicle
accessory outlet.
Restore power cord into its
compartment.
4. VEC271MG DIAGRAM
1. Powerful replaceable halogen spotlight
2. ON/OFF power switch for area light
3. ON/OFF/hazard (3-way) switch for the
spotlight
6
4. Rubberized handle
5. Rubberized base
6. Rubberized bezel
7. Tools — (Hammer, Phillips screwdriver, Flathead screwdriver, Hex-
key set, Adjustable wrench and Slip-joint pliers)
8. Reflector panel
9. Red LED flashing hazard light 12 volt power cord, with
10. 10 amp overload protection (Fuse located inside barrel)
5. REPLACEMENT PARTS
For replacement parts (bulbs, cords, fuses, etc.), contact Vector
Customer Service: (954) 584-4446 or toll-free (866) 584-5504.
5.1 HALOGEN SPOTLIGHT REPLACEMENT
Pull rubberized bezel off spotlight.
Unscrew the protective ring (2 small screws, Phillips
screwdriver needed.)
Remove the lens carefully.
•Remove the rubber insulator.
Remove the halogen bulb, by pushing 2 small wires together
and pull gently.
Replace the bulb, make sure it is secure.
Replace the protective ring and carefully tighten small screws.
Do not over tighten!
•Push the black rubberized bezel back into place.
5.2 FUSE REPLACEMENT DIAGRAM
6. SPECIFICATIONS
MODEL VEC271MG Portable 1,000,000 Candle Power Spotlight and Tool Kit
BULB H3, 55 watt
POWER CORD Use with 12 volt DC vehicle accessory outlet
HEIGHT 8.5 in (21.6 cm)
LENGTH 15.5 in (39.4 cm)
MAKE SURE FUSE IS REPLACED WITH SAME TYPE AND AMP
RATING. ELECTRIC SHOCK COULD RESULT IF DIRECTIONS ARE
NOT FOLLOWED.
7
WIDTH 4.0 in ( 10.2cm)
WEIGHT 12.5 lbs (5.67 Kg)
FUSE 10 amp
7. VECTOR ONE YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty,
other than described herein. This Vector Manufacturing, Ltd. product is warranted, to the original
purchaser only, to be free of defects in materials and workmanship for one year from the date of
purchase without additional charge. The warranty does not extend to subsequent purchasers or
users. Vector Manufacturing, Ltd. will not be responsible for any amount of damage in excess of
the retail purchase price of the product under any circumstances. Incidental and consequential
damages are specifically excluded from coverage under this warranty. This product is not intended
for commercial use. This warranty does not apply to accessories or damage to units from misuse
or incorrect installation. Misuse includes wiring or connecting to improper polarity power sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage prepaid
to Vector Manufacturing. Any defective product, other than accessories, that is returned to Vector
Manufacturing within 30 days of the date of purchase will be replaced free of charge. If such a
product is returned more than 30 days but less than one year from the purchase date, Vector
Manufacturing will repair the unit or, at its option, replace it free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at Vector
Manufacturing’s option. A unit may be replaced with a new or reconditioned unit of the same or
comparable design. The repaired or replaced unit will then be warranted under the terms of the
remainder of the warranty period. The customer is responsible for the shipping charges on all
returned items after 30 days. During the warranty period, Vector Manufacturing, Ltd. will be
responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting
from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to
usage or exposure to sunlight), accidents, damage during shipping to our service facility,
alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions for
care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department (954) 584-
4446 or toll free (866) 584-5504 for general repair information and charges if applicable. You
may also contact us through our website www.vectormfg.com.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the
purchaser specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing Technical Support by
telephone, fax or mail. We suggest that you keep the original packaging in case you need to ship
the unit. When returning a product, include your name, address, phone number, dated sales
receipt (or copy) and a description of the reason for return and product serial number. After
© 2003 VECTOR MANUFACTURING, Ltd.
FT. LAUDERDALE, FL 33312 MADE IN CHINA
REV.121203
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vector 000 CANDLE POWER SPOTLIGHT Owner's Manual & Warranty Information

Type
Owner's Manual & Warranty Information
This manual is also suitable for

Vector 000 CANDLE POWER SPOTLIGHT is a compact, durable and portable system that features:

  • A powerful halogen beam spotlight, ideal for illuminating large areas or objects at a distance.
  • A very efficient LED area light, perfect for providing diffused lighting in smaller spaces or for close-up work.
  • An emergency flashing red hazard light, which can be used to warn of potential hazards or to attract attention in case of an emergency.
  • A rubberized grip for easy portability and a rubberized base for stability.
  • A rugged carry case to protect the spotlight and tools during transport and storage.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI