Samsung LW20M11C User manual

LCD TV

LW15M13C

LW17M11C

LW20M11C

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

TELETEXT

ENG-00-13.qxd 10/30/03 3:44 AM Page 1

English-2

Caution

CAUTION:

TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION

The lightning flash and arrow head

within the triangle is a warning sign

alerting you of “dangerous voltage”

inside the product.

The exclamation point within the

triangle is a warning sign alerting

you of important instructions

accompanying the product.

WARNING:TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The main voltage is indicated on the rear of your set and the frequency is 50 or 60 Hz.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

The

Samsung logo is the registered trademarks of Samsung Electronics Co., Ltd.; Microsoft, Windows

®

and Windows

®

NT

are registered trademark of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics

Standard Association. All other product names mentioned herein may be the trademarks or registered trademarks of their

respective owners.

European Notice (Europe Only)

Products with the CE marking comply with the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage

Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies

conformity to the following European Norms:

EN55013:1990+A12:1994+A13:1996+A14:1999 - Radio Frequency Interference

EN55020:1994+A11:1996+A12/A13/A14:1999 - Electromagnetic Immunity

EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics

EN61000-3-3:1995 - Voltage Fluctuations

EN60065:1998 - Product Safety

ENG-00-13.qxd 10/16/03 10:11 PM Page 2

Do not install the product in a confined

space with poor ventilation,

such as on a bookshelf or in a closet.

(An increase in internal temperature can

be a fire hazard.)

Do not plug too many appliances

into one socket.

(It may cause the socket to

overload, which can result in a fire.)

Do not forcibly bend, pull or put

a heavy object on the power cord.

(It may cause an electric shock or a fire.)

Do not place the power cord near

a heating device. (The protective coating

of the cord may melt off, which can cause

an electric shock or a fire.)

English-3

Safety Instructions

These illustrations represent precautions concerning your set.

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS

Do not expose your set to extreme

temperature or humidity conditions.

Do not expose your set to

direct sunlight.

Do not expose your set to any liquids.

If your set is broken,

do not try to repair it yourself.

Contact qualified service personnel.

During storm conditions (especially when

there is lightning) unplug your set from

the mains socket and aerial.

If the remote control is not used for a long

period of time, remove the batteries and

store it in a cool, dry place.

ENG-00-13.qxd 10/21/03 2:17 AM Page 3

English-4

Contents

FOREWORD

Caution..........................................................................................................

2

Safety Instructions.........................................................................................

3

CONNECTING AND PREPARING YOUR TV

Viewing the Control Panel.............................................................................

6

Viewing the Connection Panel......................................................................

7

-

Connecting an Aerial or Cable Television Network....................................

8

-

Connecting a Set-Top Box, VCR, or DVD.................................................

8

-

Connecting External A/V Devices..............................................................

8

-

Kensington Slot..........................................................................................

8

Viewing Pictures From External Sources......................................................

9

Inserting the Batteries in the Remote Control...............................................

9

Viewing the Remote Control (All Functions Except Teletext)........................

10

Viewing the Remote Control (Teletext Functions).........................................

11

Switching On and Off....................................................................................

12

Placing in Standby Mode ..............................................................................

12

Becoming Familiar with the Remote Control.................................................

13

Plug & Play....................................................................................................

14

Selecting TV Mode or an Input Source.........................................................

16

Editing an Input Source Name......................................................................

17

Choosing Your Language..............................................................................

18

SETTING THE CHANNELS

Storing Channels Automatically.....................................................................

19

Storing Channels Manually ...........................................................................

20

Editing the Channels.....................................................................................

22

Sorting the Stored Channels.........................................................................

23

Giving Channels Names................................................................................

24

Fine Tuning Channel Reception....................................................................

25

SETTING THE PICTURE

Changing the Picture Standard.....................................................................

26

Adjusting the Custom Picture........................................................................

27

Adjusting the Screen Background Colour.....................................................

28

Changing the Picture Size.............................................................................

29

Freezing the Current Picture.........................................................................

29

ENG-00-13.qxd 10/16/03 10:11 PM Page 4

English-5

Contents

SETTING THE SOUND

Changing the Sound Standard......................................................................

30

Selecting the Sound Mode............................................................................

31

SETTING THE TIME

Setting the Clock...........................................................................................

32

Switching Off Automatically...........................................................................

33

Switching the television On and Off Automatically........................................

34

USING THE VARIOUS FUNCTIONS

Selecting the Blue Screen Mode...................................................................

35

Displaying Information...................................................................................

35

USING THE TELETEXT FEATURE

Teletext Feature.............................................................................................

36

Displaying the Teletext Information ...............................................................

37

Selecting a Page by Number ........................................................................

38

Using FLOF to Select a Page.......................................................................

39

Storing Teletext Pages ..................................................................................

39

RECOMMENDATIONS FOR USE

Troubleshooting: Before Contacting Service Personnel ...............................

40

Technical and Environmental Specifications.................................................

41

Maintenance of Your Telelvision....................................................................

42

Attaching a Wall or Arm mounting device.....................................................

43

Installing VESA compliant mounting devices................................................

44

Kensington Slot.............................................................................................

45

Wiring the Mains Power Supply Plug (UK Only)...........................................

46

Symbols

Press Information Note

ENG-00-13.qxd 10/16/03 10:11 PM Page 5

English-6

Viewing the Control Panel

TV/VIDEO

Displays a menu of all of the available input sources

(TV - AV1 - AV2 - S-VIDEO).

MENU

Opens the on-screen menu.

- +

Moves the selector left or right on the OSD.

Increases or decreases the level of audio volume.

+

:

Display a submenu containing selections

for the current menu option.

-

: Return to the previous menu.Close the

on-screen menu system on main menu.

Moves the selector up or down on the OSD.

Increases or decreases the channel number.

POWER

Turns ON/OFF your set.

SPEAKERS

REMOTE CONTROL SENSOR

POWER INDICATOR

Lights up when you turn the power off.

HEADPHONE JACK

ENG-00-13.qxd 10/16/03 10:11 PM Page 6

English-7

Viewing the Connection Panel

Whenever you connect an audio or video system to your set,

ensure that all elements are switched off.

Refer to the documentation supplied with your equipment for

detailed connection instructions and associated safety precautions.

Option

ENG-00-13.qxd 10/16/03 10:11 PM Page 7

English-8

Viewing the Connection Panel

Connecting an Aerial or Cable Television Network (depending on the model)

To view television channels correctly, a signal must be received by the set from one of the

following sources:

- An outdoor aerial

- A cable television network

- A satellite network

Connecting a Set-Top Box, VCR, or DVD

- Connect the VCR or DVD SCART cable to the SCART connector of the VCR or DVD.

- If you wish to connect both the Set-Top Box and VCR (or DVD), you should connect the

Set-Top Box to the VCR (or DVD) and connect the VCR (or DVD) to your set.

Connecting External A/V Devices

- Connect RCA or S-VIDEO cables to an appropriate external A/V device such as a VCR, DVD, or Camcorder.

- Connect RCA audio cables to “AUDIO (L)” and “AUDIO (R)” on the rear of your set and the other ends to

corresponding audio out connectors on the A/V device.

Kensington Slot

- This television has been designed to apply a burglarproof lock.

Retractable Stand

Tilt the screen until you feel comfortable.

The maximum tilt angle is 13 degrees in the backward direction.

Please do not tilt the television beyond the specified range.

Using excessive force to tilt the television beyond the

specified range may cause permanent damage to the

mechanical part of the stand.

ENG-00-13.qxd 10/16/03 10:11 PM Page 8

English-9

Viewing Pictures From External Sources

Once you have connected up your various audio and video systems,

you can view the different sources by selecting the appropriate input.

1

Check that all the necessary connections have been made

(refer to pages

8

for further details).

2

Video button...

Press the Video button to choose Video mode.

The input sources are displayed in the following order:

AV1 - AV2 - S-Video.

TV button...

Press the TV button to choose TV mode.

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when you:

Purchase your set

Find that the remote control is no longer operating correctly

1

Remove the cover on the rear of the remote control by pressing the

symbol downwards and then pulling firmly to remove it.

2

Install two

AAA

size batteries.

◆

+

on the battery against

+

on the remote control

◆

-

on the battery against

-

on the remote control

3

Replace the cover by aligning it with the base of the remote control

and pressing it back into place.

Do not mix battery types, i.e. alkaline and manganese.

ENG-00-13.qxd 10/16/03 10:11 PM Page 9

English-10

Viewing the Remote Control

Numeric buttons for

direct channel access

Sound mode selection

Picture freeze

Picture size selection

Television On/Off

Picture effect selection

One/Two-digit channel selection

Use to see information

on the current broadcast

Next channel

Previous channel

Available source selection

Exit the OSD

Control the cursor

in the menu

Previous channel

Sound effect selection

Temporary sound switch-off

Menu display and

change confirmation

Automatic switch-off

Volume up or down

The performance of the remote control may be affected by bright light.

(All Functions Except Teletext)

ENG-00-13.qxd 10/16/03 10:11 PM Page 10

English-11

Viewing the Remote Control

(Teletext Functions)

Teletext size selection

Teletext cancel

P :Teletext next page

P :Teletext previous page

Teletext reveal

Teletext mode selection

(LIST/FLOF)

Teletext sub-page

Teletext display/

mix both teletext information

and the normal broadcast

Teletext store

Teletext Index

Teletext hold

ENG-00-13.qxd 10/16/03 10:11 PM Page 11

English-12

Switching On and Off

The mains lead is attached to the rear of your set.

If you purchased this set in the United Kingdom,

refer to page

46

for further instructions on plug wiring.

1

Plug the mains lead into an appropriate socket.

Result

: When the power cord is plugged in, the LED turns red.

2

Press the

POWER

button to switch on.

3

To switch off, press the

POWER

button again.

Placing in Standby Mode

Your set can be placed in Standby mode in order to reduce the

power consumption.

The Standby mode can be useful when you wish to interrupt viewing

temporarily (during a meal, for example).

1

Press the

POWER

button.

2

To switch back on, simply press the

POWER

button again

or a numeric button.

Do not leave your set in Standby mode for long periods of

time (when you are away on holiday, for example).

Turn off by pressing the

POWER

button.

It is best to unplug the set from the mains and aerial.

ENG-00-13.qxd 10/16/03 10:11 PM Page 12

English-13

Becoming Familiar with the Remote Control

The remote control is used mainly to:

Change channels and adjust the volume

Set up your set using the on-screen menu system

The following table presents the most frequently used buttons and their

functions.

Button Viewing Function Menu Function

Used to display the next

-

stored channel.

Used to display the

-

previous stored channel.

PRE-CH Used to switch repeatedly between the last two channels

displayed. (

PRE-CH; Previous Channel)

- Used to display the corresponding channels.

-/--

Used to select a channel numbered ten or over.

Press this button, and the “

--

” symbol is displayed.

Enter the two-digit channel number.

Used to increase the

-

volume.

Used to decrease the

-

volume.

MUTE Used to switch the sound off temporarily.

To turn the sound back on, press this button again,

or press the

+ or - button.

MENU Used to display the Used to return to the previous

on-screen menu system. menu or normal viewing.

EXIT Used to exit the menu system and return directly to normal

viewing.

Display a submenu containing selections for the

current menu option.

Search backwards/forwards manually for channels

Increase/decrease a menu option value

ENG-00-13.qxd 10/16/03 11:53 PM Page 13

English-14

Plug & Play

When the set is initially powered ON, you are automatically presented

with a series of basic customer settings.

The following settings are available.

1

If the set is in standby mode, press the

POWER

button

on the remote control.

Result

: The message

Plug & Play

is displayed.

It appears for a little while, and then the

Language

menu is automatically displayed.

2

Select the appropriate

Language

by pressing the or button.

The available languages are listed

.

You can choose one of 18 Languages.

3

Press the

ENTER

button to confirm your choice.

Result

: The message

Ant. Input Check

is displayed with

OK

selected.

4

Press the

ENTER

button.

5

Select your

Country

by pressing the or button.

Press the

ENTER

button.

Result

: The country menu is displayed:

Belgie - Deutschland - Espania - France - Italia -

Nederland - Schweiz - Sverige - UK - East Europe

- Others

6

Select the

Hour

or

Min

by pressing the or button.

Set the

Hour

or

Min

by pressing the or button.

(Refer to “

Setting the Clock

” on page

32

)

7

Press the

MENU

button to confirm your setting.

Result

: The message

Enjoy your watching

is displayed,

and then the channel which has been stored will be

activated.

ENG-14-29.qxd 10/16/03 11:55 PM Page 14

English-15

Plug & Play

If you want to reset this feature...

1

Press the

MENU

button.

Result

: The main menu is displayed.

2

Press the or button to select the

Setup

.

Result

: The options available in the

Setup

group are displayed.

3

Press the

ENTER

button.

4

Press the or button to select the

Plug & Play

.

Press the

ENTER

button.

Result

: The message

Plug & Play

is displayed.

5

For further details on how to set up this feature, refer to page

14 and 23.

The Sort menu is displayed after the Plug&Play ends.

ENG-14-29.qxd 10/16/03 10:12 PM Page 15

English-16

Selecting TV Mode or an Input Source

You can choose TV mode or change to an input source connected to

the TV set. Use this button to choose an input source that you would

like to watch.

1

Press the

MENU

button.

Result

: The main menu is displayed.

2

Press the or button to select the

Input

.

Result

: The options available in the

Input

group are displayed.

3

Press the

ENTER

button.

4

Press the

ENTER

button.

Result

: The

TV/Video

is selected.

5

Press the or button to move to the input source that

you wish to choose.

Press the

ENTER

button.

Result

: The input source changes to the one you have chosen.

ENG-14-29.qxd 10/16/03 10:12 PM Page 16

English-17

Editing an Input Source Name

Entering the names of the input source devices connected to the input

ports on the TV set allows you to find and choose an input source that

you would like to watch in a quick and convenient manner.

1

Press the

MENU

button.

Result

: The main menu is displayed.

2

Press the or button to select the

Input

.

Result

: The options available in the

Input

group are displayed.

3

Press the

ENTER

button.

4

Press the or button to select the

Edit Name

.

Press the

ENTER

button.

5

Press the or button to move to the input source that

you wish to edit.

Press the

ENTER

button.

Result

: The following options are available:

AV 1 - AV 2 - S-Video

6

Select the required device by pressing the or repeatedly.

Result

: The following options are available:

---- - VCR - DVD - Cable STB - HD STB -

Satellite STB - AV Receiver - DVD Receiver -

Game - Camcorder - DVD Combo - DHR - PC

7

When you are satisfied with your choice, press the

EXIT

button to

return to normal viewing.

ENG-14-29.qxd 10/16/03 10:12 PM Page 17

English-18

Choosing Your Language

When you start using your set for the first time, you must select the

language which will be used for displaying menus and indicators.

1

Press the

MENU

button.

Result

: The main menu is displayed.

2

Press the or button to select the

Setup

.

Result

: The options available in the

Setup

group are displayed.

3

Press the

ENTER

button.

4

Press the or button to select the

Language

.

Press the

ENTER

button.

5

Select a particular

Language

by pressing the or button

repeatedly.

6

When you are satisfied with your choice, press the

EXIT

button to

return to normal viewing.

ENG-14-29.qxd 10/16/03 10:12 PM Page 18

English-19

Storing Channels Automatically

You can scan for the frequency ranges available to you (and availability

depends on your country). Automatically allocated programme numbers

may not correspond to actual or desired programme numbers.

However you can sort numbers manually and clear any channels you

do not wish to watch.

1

Press the

MENU

button.

Result

: The main menu is displayed.

2

Press the or button to select the

Channel

.

Result

: The options available in the

Channel

group are displayed.

3

Press the

ENTER

button.

4

Press the or button to select

ATM

.

Press the

ENTER

button.

Result

:

The

Start

is selected.

5

Press the

ENTER

button to search the channels.

The sub menu is changed from

Start

to

Stop

with channel

search started.

Result

: The search will end automatically.

Channels are sorted and stored in an order which reflects

their position in the frequency range, (with lowest first and

highest last). The programme originally selected is then

displayed.

To return to the previous menu, press or button to select

Return

and then press

ENTER

button.

To stop the search before it has finished, press the

ENTER

button to search the channels.

6

When the channels have been stored, you can:

Add or delete the channels (refer to page 22)

Sort them in the order required (refer to page 23)

Assign a name to the stored channels (refer to page 24)

Fine tune channel reception if necessary (refer to page 25)

ENG-14-29.qxd 10/16/03 10:12 PM Page 19

English-20

Storing Channels Manually

You can store up to 100 channels, including those received via

cable networks.

When storing channels manually, you can choose:

Whether or not to store each of the channels found

The programme number of each stored channel which you wish to

identify

1

Press the

MENU

button.

Result

: The main menu is displayed.

2

Press the or button to select the

Channel

.

Result

: The options available in the

Channel

group are displayed.

3

Press the

ENTER

button.

4

Press the or button to select the

Manual Store

.

Press the

ENTER

button.

Result

: The options available in the

Manual Store

group are

displayed with the

Prog. No.

selected.

5

Press the or button to select

Colour System

.

Press the

ENTER

button.

Select the

Colour System

required by pressing the or button

repeatedly and then press the

ENTER

button.

Result

: The colour standards are displayed in the following order:

AUTO - PAL - SECAM - NT4.43

6

Press the or button to select

Sound System

.

Press the

ENTER

button.

Select the

Sound System

required by pressing the or button

repeatedly and then press the

ENTER

button.

Result

: The sound standards are displayed in the following order:

BG - DK - I - L

7

For all the channels to move to the required channel numbers,

repeat steps

5

to

6

after selecting

Prog. No.

by pressing the

or button.

ENG-14-29.qxd 10/16/03 10:12 PM Page 20

Page is loading ...

Samsung LW20M11C User manual

This manual is also suitable for

Samsung LW20M11C User manual

Related papers

Other documents