Dolby Laboratories Digital-Satellite-Receiver User manual

Brand: Dolby Laboratories

Model: Digital-Satellite-Receiver

Category: TV set-top boxes

Type: User manual

DDiiSSEEqqCC

1.2

For reception of free-to-air and encrypted

(e.g. VIACCESS, IRDETO, SECA etc. )

satellite programmes.

Operating Manual

DIGITAL-

Satellite-Receiver

Features integrated decoding system

plus PCMCIA interface to accommodate a CI module.

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 1

1 Index

1 Contents . . . . . . . . . . . . . . . . .2, 5, 6

2 Illustrations . . . . . . . . . . . . . . . . . . .3

Introduction . . . . . . . . . . . . . . . . . . .7

3 Please read this first - . . . . . . . . . .8

Safety precautions! . . . . . . . . . . . .9

4 Connections . . . . . . . . . . . . . . . . .10

4.1 Mains power connection . . . . . . . . . . . . . .11

4.2 External unit . . . . . . . . . . . . . . . . . . . . . . . .11

4.3 Connection to a television set . . . . . . . . . .11

4.4 Video cassette recorder (VCR) . . . . . . . . .12

4.5 HiFi amplifier . . . . . . . . . . . . . . . . . . . . . . .13

4.6 Serial interface (RS 232) . . . . . . . . . . . . . .13

5 Initial installation (AutoInstall) . . .13

6 Settings . . . . . . . . . . . . . . . . . . . . .17

6.1 User language . . . . . . . . . . . . . . . . . . . . . .17

6.2 Basic settings . . . . . . . . . . . . . . . . . . . . . . .17

6.2.1 Parental control . . . . . . . . . . . . . . . . . . . . .17

6.2.2/3 Time difference (time)/country . . . . . . . . . .18

6.2.4 OSD setting . . . . . . . . . . . . . . . . . . . . . . . .18

6.3 Audio/video settings . . . . . . . . . . . . . . . . . .18

6.3.1 Picture format . . . . . . . . . . . . . . . . . . . . . . .19

6.3.2 Language - audio signal . . . . . . . . . . . . . .19

6.3.3 Sub-titles . . . . . . . . . . . . . . . . . . . . . . . . . .19

6.3.4 SCART mode TV . . . . . . . . . . . . . . . . . . . .19

6.3.5 Video system* . . . . . . . . . . . . . . . . . . . . . .19

6.3.6 Dolby-Digital (AC 3)* . . . . . . . . . . . . . . . . .19

6.3.7 UHF output channel* . . . . . . . . . . . . . . . . .20

6.4 Antenna configuration . . . . . . . . . . . . . . . .20

6.4.1 Switching DiSEqC on/off . . . . . . . . . . . . . .21

6.4.2 Setting switching matrix . . . . . . . . . . . . . . .21

6.4.3 LNB properties . . . . . . . . . . . . . . . . . . . . . .22

6.4.4 Rotating dish antenna (DiSEqC 1.2) . . . . .23

7 Operation . . . . . . . . . . . . . . . . . . . .23

7.1 Switching on/off . . . . . . . . . . . . . . . . . . . . .23

7.2 Programme selection . . . . . . . . . . . . . . . . .24

7.3 Reception of encrypted programmes . . . . .26

7.3.1 Special functions* . . . . . . . . . . . . . . . . . . .26

7.3.1.1 Multifeed options* . . . . . . . . . . . . . . . . . . .27

7.3.1.2 Time management* . . . . . . . . . . . . . . . . . .27

7.3.1.3 Smartcard PIN code* . . . . . . . . . . . . . . . . .28

7.3.1.4 Changing the Smartcard PIN code* . . . . .28

* Only with devices with this

equipment

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 2

7.4 Volume control . . . . . . . . . . . . . . . . . . . . . .28

7.5 Selecting another language . . . . . . . . . . . .29

7.5.1 Dolby Digital (AC3 mode) . . . . . . . . . . . . .29

7.6 TV/radio switching . . . . . . . . . . . . . . . . . . .29

7.7 Return to last programme selected. . . . . .30

7.8 Display time and programme info . . . . . . .30

7.9 Additional programme information . . . . . . .30

7.10 Transponder information . . . . . . . . . . . . . .30

7.11 Fixed image . . . . . . . . . . . . . . . . . . . . . . . .30

7.12 Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

7.13 Sub-titles . . . . . . . . . . . . . . . . . . . . . . . . . .32

7.14 Electronic Programme Guide (SFI)32

7.14.1 Reading/downloading SFI data . . . . . . . . .32

7.14.2 Interrupting download procedure . . . . . . . .33

7.14.3 Calling up electronic programme guide . . .33

7.14.4 Table with current contents . . . . . . . . . . . .33

7.14.5 Table with following contents . . . . . . . . . . .34

7.14.6 Preview . . . . . . . . . . . . . . . . . . . . . . . . . . .34

7.14.7 SFI function . . . . . . . . . . . . . . . . . .34

7.14.7.1 SFI information . . . . . . . . . . . . . . . . . . . . . .34

7.14.7.2 Pre-selecting a programme . . . . . . . . . . . .35

7.14.7.3 Recording a programme . . . . . . . . . . . . . .35

7.14.7.4 SFI programme overview . . . . . . . . . . . . . .36

7.14.7.5 SFI genres . . . . . . . . . . . . . . . . . . . . . . . . .36

7.14.8 Exiting from SFI . . . . . . . . . . . . . . . . . . . . .37

7.15 Timer . . . . . . . . . . . . . . . . . . . . . . .37

7.15.1 Programming the timer . . . . . . . . . . . . . . .37

7.15.2 Changing timer programming . . . . . . . . . .39

7.15.3 Deleting timer programming . . . . . . . . . . .39

8 Changing the basic programming 40

8.1 Configuring the Favourites list . . . . . . . . . .40

8.1.1 Calling up the Navigator . . . . . . . . . . . . . .40

8.1.2 Adding programmes to Favourites list . . . .41

8.1.3 Deleting programmes . . . . . . . . . . . . . . . . .41

8.1.3.1 Deleting from Favourites list . . . . . . . . . . .41

8.1.3.2 Deleting from Complete list . . . . . . . . . . . .42

8.1.4 Sorting programmes . . . . . . . . . . . . . . . . .42

8.1.5 Programming electr. programme guide . . .43

8.1.6 Blocking programmes (parental control) . .44

8.2 Changing Receiver PIN . . . . . . . . . . . . . . .45

8.3 Searching for programmes . . . . . . . . . . . .45

8.3.1 Automatic search/scan . . . . . . . . . . . . . . . .46

8.3.2 Searching on a satellite . . . . . . . . . . . . . . .46

8.3.3 Searching on a transponder . . . . . . . . . . .47

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 3

8.3.4 Manual search . . . . . . . . . . . . . . . . . . . . . .48

8.3.5 After the search . . . . . . . . . . . . . . . . . . . . .48

8.4 Service settings . . . . . . . . . . . . . . . . . . . . .49

8.4.1 Activating default (factory) settings . . . . . .49

8.4.2 Deleting all programmes . . . . . . . . . . . . . .49

8.4.3 SFI channel . . . . . . . . . . . . . . . . . . . . . . . .50

8.4.4 Software update . . . . . . . . . . . . . . . . . . . . .50

8.4.5 Copying settings . . . . . . . . . . . . . . . . . . . .51

8.5 System configuration . . . . . . . . . . . . . . . . .51

8.6 Condtional Access* . . . . . . . . . . . . . . . . . .52

9 Operating a rotating antenna . . . .52

9.1 East and West limits . . . . . . . . . . . . . . . . .52

9.2 Geo-positioning . . . . . . . . . . . . . . . . . . . . .53

9.3 Setting satellite position . . . . . . . . . . . . . . .55

9.3.1 Selecting satellite position . . . . . . . . . . . . .55

9.3.2 Adjusting the satellite antenne . . . . . . . . . .56

9.3.3 Storing the satellite position . . . . . . . . . . . .57

9.4 Current satellite liste . . . . . . . . . . . . . . . . .58

9.5 Deleting satellite position . . . . . . . . . . . . .58

9.6 Turning to reference position . . . . . . . . . . .58

10 Technical Terms . . . . . . . . . . . . . .59

11 Technical Data . . . . . . . . . . . . . . .61

12 Trouble-shooting guide . . . . . . . . .64

* Only with devices with this

equipment

Your appliance carries the CE logo and complies

with all relevant EU standards.

Subject to change without notice, not responsible for printing errors.

Correct as at 03/03

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 4

2 Illustrations

On/Standby

Numeric keys

Programme list on/off

Back

Help

Stop

Menu on/off

Sound on/off

EXTERNAL

Language

Programme -

Multi-function keys

Volume +

Programme +

TV/Radio mode

SFI

Option

Teletext

Volume -

arrow key right

arrow key left

arrow key up

arrow key down

Info

Remote control

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 5

* Only for receivers equipped with

this feature

LNC

input

Input terrestrial

antenna*

LNC out-

put

SCART socket

Digital audio outputs

SCART socket

VCR

Analogue audio

outputs

RS 232

interface

RF out-

put*

Mains socket

Inserting the CI module:*

> Please follow the instructions of the CI module and card

manufacturer.

> Insert the smart card selected in the appropriate CI module.

> Now insert the CI module carefully in the slot provided.

Card reader for Smartcard:*

> Insert the Smartcard (gold chip face down, and in the direction of

insertion) carefully into the card reader, as far as it will go.

On/Standby

Programme select

up/down

LED display*

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 6

Dear customer,

congratulations on your decision to select this digital receiver .

This operating manual will help you to fully utilise the compre-

hensive functions of your new digital receiver.

We have made the operating instructions as easy to under-

stand and as brief as possible.

This is a digital receiver of the new generation. We wish you

many years of enjoyment with your digital receiver!

Your

Service Team

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 7

3 Please read this first

> Before you set up your unit for operation, please first

check that the package contains all the components

that should be there. The following are supplied as

standard:

1 digital receiver, 1 mains power cable, 1 remote con-

trol unit, 1 operating manual, 1 guarantee card, 2 bat-

teries (1,5V AAA size).

> Insert the batteries provided in the battery compart-

ment of the remote control unit. Note the correct pola-

rity when inserting the batteries.

> Before connecting the digital receiver, please first read

the safety notes in Chapter 3.

> Chapters 4, 5 and 6 describe connection of the

receiver, and adjusting it to the external installation

(dish antenna, LNC, etc.), to the television set, VCR,

etc. These settings need only be made once during

initial installation, and need only be adjusted or chan-

ged when there are any changes in your equipment,

i.e. if a different external unit is connected, or additio-

nal appliances are connected.

> Chapter 7 describes all the functions necessary for

day-to-day operation, such as programme selection or

volume adjustment.

> Chapter 8 contains information on how to add new

programmes, and how to change the programme

order.

> Chapter 9 describes the settings necessary for the

operation of a rotating antenna unit.

> Technical terms used in the operating manual are

explained in Chapter 10.

> Technical data may be found in Chapter 11.

> Assistance in finding and eliminating problems can be

found in the trouble-shooting guide in Chapter 12.

Important notes on operation

The use of a so-called "On Screen Display" simplifies the

operation of the digital receiver, and reduces the number of

keys required on the remote control unit. All functions are

displayed on the screen, and can be controlled by a few key-

strokes. Related functions are grouped together in a "MENU".

The selected function is highlighted in a different colour. The

lower line of the display shows coloured bars representing the

red, green, yellow and blue function keys. These coloured

bars represent different functions in the various menues,

which can be executed by pressing the appropriate colour-

coded key (“multi-function key”) on the remote control unit.

The function keys are only active when a brief description is

displayed in the appropriate field.

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 8

The descriptions of keys and terms that appear in the OSD

menu are printed in bold type in this operating manual.

Help function:

Where available in the menu, pressing the blue function key

will cause a help text to be displayed, pressing again will

return to normal operation.

Note on disposal

The packaging of your unit consists entirely of recyclable

material. Please sort the components appropriately, and

dispose of them via the “Dual System”, or your equivalent

recycling system. Please note that spent batteries from the

remote control unit, as well as electronic components in

general, should not be disposed of in your domestic refuse.

For appropriate disposal, consult your specialist retailer, or

consult your local authority).

Safety notes

For your own protection you should read the notes on safety

precautions carefully before commencing operation of your

new unit. The manufacturer bears no responsibility for dama-

ge caused by non-observance of the safety precautions, or

by inappropriate handling.

> To ensure adequate circulation of air, place the unit on

a smooth horizontal surface and do not place any

objects on top of the unit. The top cover contains air

slits which permit heat to escape from the interior of

the unit.

> Do not place any burning items, such as burning

candles, on top of the unit.

> Do not place any containers filled with liquid, such as

vases, on top of the unit, and ensure the unit remains

dry, i.e. it must not be subjected to water spray or dro-

plets.

> The unit may only be operated in a temperate climate.

> Do not open the cover of your unit! You are in danger

of receiving an electric shock. If it becomes necessary

to open the unit, this should only be done by trained

personnel.

In the following cases you should disconnect the unit

from the mains power and consult a specialist repair ser-

vice:

> the mains cable or the mains plug are damaged

> the unit has been exposed to humidity, or liquid has

entered the casing

> in case of severe malfunction

> in case of significant external damage

When not in use

The unit should be disconnected from the mains power sup-

ply if it will not be operated for an extended period (e.g. when

you are away on holiday), or during an electric storm.

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 9

* Only for receivers equipped with

this feature

Connecting the DVB receiver to a satellite

installation

a. Mains connection

b. Connection of the LNC with the LNC input (LNC IN) of

the DVB receiver.

c. Connection of the LNC output with the LNC input of an

analogue receiver.

d. Scart connection of the DVB receiver with the television

set.

e.* Connection of the RF output with the antenna input of

the TV set.

f.* Connection of a terrestrial antenna with the Terrestrial

antenna input of the DVB receiver.

g. Scart connection of the video recorder with the VCR

Scart socket of the DVB receiver.

VCR

Analogue Receiver

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 10

4 Connections

The references a b c etc. mentioned below refer to the illu-

stration on page 10.

4.1 Mains power connection

The digital receiver should only be connected to the mains

power supply after it has been completely connected with all

other components in the system. This serves to avoid the

digital receiver or other components being damaged or

destroyed.

a When you have completed making all the connec-

tions, use the mains cable supplied to connect the

receiver to a mains power outlet 85-288 V/50-60 Hz.

4.2 External unit

4.2.1 Single operation

b Use a suitable coaxial cable to connect the LNC

input of the digital receiver to the LNC of your

external unit. Please also note Point 6 “Settings”.

4.2.2 Operation with an additional receiver in a sin-

gle-receiver installation

c If you wish to operate an additional unit in a single-

receiver installation (e.g. an analogue receiver or an

ADR receiver), you can connect the LNC input of the

additional receiver with the LNC output of the DVB

receiver by means of a suitable coaxial cable. In order

for the additional receiver to receive the satellite sig-

nal, your DVB receiver must remain in Standby mode

at all times. When the DVB receiver is switched on,

this will take over the priority control over the LNC.

4.3 Connection to a television set

When you have completed connecting your digital receiver to

the television set as described in this chapter, it may be

necessary to adjust the digital receiver to the television bro-

adcast standard of your TV set before proceeding with further

settings.

See also Point 6.3.5 (Video system).

4.3.1 On SCART cables

In order to enjoy the optimum picture quality you should con-

nect the digital receiver to your television set by means of a

SCART cable.

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 11

Proceed as follows:

d Connect the receiver (SCART socket TV) and the

television set (SCART socket) by means of a SCART

cable. If your television set is appropriately equipped,

this will be switched automatically to AV, and thus to

satellite reception, when the digital receiver is switched

on.

4.3.2 On RF cables*

If your television set is not equipped with a SCART socket,

the digital receiver must be connected to the antenna input of

the television set. In this case, sound can only be reproduced

in mono mode.

Proceed as follows:

e Use a suitable TV connection cable to connect the

receiver (RF output) to the antenna input of the tele-

vision set.

f The cable coming from the terrestrial antenna must be

connected to the Terrestrial antenna input of the

digital receiver.

You must now set the television set to the output channel of

the digital receiver. Select a free programme slot on the tele-

vision set, and tune it to Channel 38 (if necessary, refer to the

operating manual of the television set).

If you cannot obtain a clear picture on Channel 38, this chan-

nel or a neighbouring channel may already be tuned to a

channel being received via the antenna. You can confirm this

by briefly removing the antenna cable from the Terrestral

antenna input socket of the digital receiver. If you then

temporarily receive a better picture, you should select a diffe-

rent channel in the range of 21 to 69 for the digital receiver.

Setting the UHF output channel

To set an optimum UHF output channel, call up the menu

Audio/Video Settings, as described in 6.3., and select the

field UHF output channel. Then proceed as desribed

under 6.3.7.

4.4 Video cassette recorder (VCR)

g Connect the video recorder to the SCART socket

VCR. When set to Play, the video recorder will deliver

a switching signal to the digital receiver. The video

recorder signal will thus be provided automatically to

the TV set.

If your video recorder does not provide a switching sig-

nal, press the key EXTERN to set your digital recei-

ver to the external AV input. Press this key again to

return to normal operation.

* Only for receivers equipped with

this feature

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 12

4.5 Hi-fi amplifier

4.5.1 Analogue

To enjoy the best possible sound quality, you can connect the

digital receiver to a hi-fi amplifier. Use a suitable cable to con-

nect the cinch sockets Audio R and Audio L of the digital

receiver to an input of the hi-fi amplifier (e.g. CD or AUX; ple-

ase note that the Phono input is not suitable!).

4.5.2 Digital

If your amplifier is equipped with an appropriate electrical or

optical input socket, connect the socket AUDIO OUT

DIGITAL electrical resp. AUDIO OUT DIGITAL opti-

cal* with the electrical resp. optical input of your amplifier.

Sampling rates of 32, 44.1 and 48 KHz are provided, depen-

ding on the broadcasting station.

In addition, this connection will reproduce the Dolby Digital

signal (AC3), where available.

4.6 Serial interface (RS 232)

The RS 232 interface is used to update the operating system,

and to facilitate pre-programming by means of a personal

computer.

5 Getting started: initial installation

When you have read the safety notes, and have connected

the unit as described in Chapter 4, you can proceed to switch

on the receiver as described in Chapter 7. When switching

on the unit for the first time, the Start window with the

AutoInstall installation assistant

(Fig. 5-1)

will be display-

ed. The installation assistant will guide you through the most

important settings of the digital receiver quickly and in an

easy-to-follow manner.

The keys on the remote control required to make the appro-

priate step in the installation are marked.

You can break off the initial installation procedure at any time

by pressing the red function key. Pressing the green func-

tion key takes you back to the previous step of the installation

procedure. This allows you to correct any entries made in

error.

If the initial installation is not carried out at all, or is interrup-

ted, your unit will start operation with its standard pre-pro-

grammed settings.

* Only for receivers equipped with

this feature

(Fig. 5-1)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 13

The initial installation procedure described hereinserves

only as an example. The exact initial installation procedure

will depend on the settings you wish to make.

Please follow closely any instructions that appear on the

screen.

Menu/OSD language:

> Press OK to display the selection window for the

Menu/OSD language.

(Fig. 5-2)

> Use the arrow keys up/down to select the prefer-

red OSD language.

> Confirm by pressing OK.

Audio language

> Use the arrow keys up/down to select the prefer-

red audio channel language.

(Fig. 5-3)

When the installation assistant has been completed,

your language selection here will be used to sort the

programmes in your Favourites list.

> Confirm by pressing OK.

Country/Time Zone

> Use the arrow keys up/down to select the time

zone of the country in which you are located.

(Fig. 5-4)

The time on the receiver clock will be set automatically

based on your selection.

> Press OK to confirm, and to proceed to the antenna

configuration.

Antenna configuration

In this step of the installation procedure you can adjust the

setting of your digital receiver to the configuration of your

antenna.

> If you wish to accept the standard antenna setting,

use the arrow keys up/down to mark the field

Standard and confirm by pressing OK.

(Fig. 5-5)

In this case, proceed to the next item, “Software

Update”.

> If the configuration of your receiving installation does

not correspond with the standard setting, mark the

field Manual and confirm by pressing OK.

DiSEqC

> If you are utilising DiSEqC components as part of your

reception installation, click on to the field Activate

and confirm by pressing OK

(Fig. 5-6).

(Additional information on DiSEqC may be

found in Chapter 10: Technical Terms.)

(Fig. 5-5)

(Fig. 5-6)

(Fig. 5-2)

(Fig. 5-3)

(Fig. 5-4)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 14

Position A/Option A

> Use the Up/down arrow keys to select the satelli-

te you wish to receive at the DiSEqC setting Position

A/Option A, and confirm by pressing OK.

(Fig. 5-7)

Position B/Option A

> Use the Up/down arrow keys to select the satelli-

te you wish to receive at the DiSEqC setting Position

B/Option A, and confirm by pressing OK.

(Fig. 5-8)

Position A/Option B

> Use the Up/down arrow keys to select the satelli-

te you wish to receive at the DiSEqC setting Position

A/Option B, and confirm by pressing OK.

(Fig. 5-9)

Position B/Option B

> Use the Up/down arrow keys to select the satelli-

te you wish to receive at the DiSEqC setting Position

B/Option B, and confirm by pressing OK.

(Fig. 5-10)

With the next step you can check again on the configuration

of your antenna.

> If you wish to confirm this setting, use the arrow

keys up/down to select the field yes, and confirm

by pressing OK.

(Fig. 5-11)

Updating the software (Pre-condition: Astra 19,2° recep-

tion)

When you have completed the settings for the antenna confi-

guration, the digital receiver will check on whether there is an

updated version of the software for your unit available via

satellite. If a new version of the software is available, you can

process a software update automatically. Use the arrow

keys right /left to select the field Update, then confirm

by pressing OK.

(Fig. 5-12).

The new software for your unit

will now be downloaded. This procedure can take several

minutes.

Searching/scanning for channels/stations

When the software version has been checked, and updated if

necessary, you can proceed to the programme search.

> Use the arrow keys up/down to mark the field All

Programmes, if you want to search for both free-to-

air and encrypted programmes, or All unencrypted

Programmes, if you want to search only for free-to-

air programmes.

(Fig. 5-13)

> Press the OK key now to confirm, and an automatic

programme scan will be carried out. All the satellites

selected in the antenna configuration step will be

scanned for programmes. This procedure may take

several minutes. Please note any messages displayed

(Fig. 5-7)

(Fig. 5-8)

(Fig. 5-9)

(Fig. 5-10)

(Fig. 5-11)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 15

on the screen.

After the Search

When the programme search has been completed, the num-

ber of transponders, programmes and new programmes

found will be displayed. In addition, you will be asked

(Fig. 5-

14)

, whether you want to accept the programmes found auto-

matically in the TV or Radio list. If you wish to accept the pro-

grammes automatically, you can then decided whether they

should be transferred to the Favourites list in sorted or

unsorted form.

In the case of a sorted acceptance of programmes found,

these will be sorted into the Favourites according to a pre-

programmed list. The order in which programmes are listed

will depend on the audio channel language selected in the

installation step Audio language. If German was selected

as the audio language, the sorting order can additionally be

differentiated according to the appropriate country (Germany,

Austria or Switzerland) selected during the installation step

Country.

If the programmes are accepted in unsorted form, the

newly found programmes are simply added in unsorted order

at the end of the Favourites list.

> Use the arrow keys right/left to select the prefer-

red type of sorting, and confirm by pressing OK.

Exiting the installation assistant

> Confirm the final message of the installation assistant

(Fig. 5-15)

by pressing OK,to return to normal opera-

tion.

(Fig. 5-15)

(Fig. 5-13)

(Fig. 5-14)

(Fig. 5-12)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 16

6 Settings

Now that you have completed connecting your new digital

receiver, and have commenced operation, you can, if you

wish, further optimize the settings of the digital receiver for

your personal preferences.

6.1 Menu language

Under this menu item you have the option of setting the

menu language according to your personal preference.

To alter the OSD language proceed as follows:

> Press the Menu key to call up the Main Menu.

(Fig. 6-1)

> Now use the arrow keys up/down to select the

menu item Menu language.

> Confirm by pressing OK.

The sub-menu Menu language will be displayed.

> Use the arrow keys up/down to select the desired

language.

> Confirm by pressing OK, this will store the selection in

memory.

> Press Back to return to the Main Menu.

6.2 Basic settings

To optimize the performance of your DVB receiver, you must

still set this to your personal preferences.

> Press the Menu key to call up the Main Menu.

> Use the arrow keys up/down to mark the item

Settings.

> Confirm by pressing OK. The sub-menu Settings

will be displayed.

(Fig. 6-2)

> Now use the arrow keys up/down to mark the

item Basic Settings.

> Confirm by pressing OK. The menu Basic Settings

will be displayed.

(Fig.. 6-3)

> Use the arrow keys up/down to move the marker

within the menu, and to change the individual posi-

tions as indicated. When selecting a menu item, plea-

se also note any messages displayed on the screen.

The following settings may be made:

6.2.1 Parental control function

Your receiver is equipped with a parental control (child-proof

lock) function. This can be used to protect important functions

(e.g. calling up the main menu) from unauthorized access. In

addition programmes to which you have blocked access as

described in Points 8.1.6 and 8.2 can only be selected after

entering a four-digit PIN code (Unit PIN).

(Fig. 6-1)

(Fig. 6-2)

(Fig. 6-3)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 17

> In this line you can use the arrow keys right/left

to set the parental control mode to Always or Auto.

Always

When the setting Always is selected, the Main Menu as well

as the programmes selected in terms of Points 8.1.6 and 8.2

are permanently blocked, regardless of the programme being

broadcast.

Auto

When the setting Auto is selected, access to the Main Menu

is not blocked. The programme lock block is only activated

when one of the selected channels carries a programme with

an age restriction.

When using a Smartcard please note Point 7.3.1.3 !

6.2.2 Time difference to GMT (hours)

Your receiver is equipped with a clock. This is synchronised

to Greenwich Mean Time via satellite signals. If you have

selected the option None under the heading Country (Point

6.2.3), you will simply need to correct the time to correspond

to your local time by using the arrow keys right/left. For

Germany, this difference is +1 hour, and +2 hours for Daylight

Savings Time.

6.2.3 Country

This function provides for automatic adjustment for summer

and winter time. Using the arrow keys right/left, enter

your home country in the line Country.

> Press the Back key to return to the menu Settings,

or press the Menu key to return to normal operation.

The settings are automatically stored in memory.

6.2.4 OSD Setting (schematic)

In this line, use the arrow keys right/left to select one of

the colour presentation options for the OSD: 3D Sand, 3D

Blue or 3D Grey.

6.3 Audio/Video settings

In order to optimize the performance of your digital receiver in

conjunction with your television set, you may wish to make

further settings in the menu Audio /Video Settings.

> Press the Menu key to call up the Main Menu.

> Use the arrow keys up/down to select the line

Settings.

> Confirm by pressing OK. The sub-menu Settings

will be displayed.

(Fig. 6-4)

> Now use the arrow keys up/down to select the

line Audio/Video Settings.

(Fig. 6-4)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 18

> Confirm by pressing OK. The menu Audio/Video

Settings will be displayed.

(Fig. 6-5)

> You can use the arrow keys up/down to move

the marker around within the menu, and change the

individual settings as indicated. When selecting a

menu item please also note any messages displayed

on screen.

The following settings can be adjusted:

6.3.1 Picture format TV set

Use the arrow keys left/right to select the appropriate

picture format for your TV set, 4:3 or 16:9. This function

provides for automatic adjustment of the picture format bro-

adcast to your television set.

6.3.2 Language (Audio signal)

Use the arrow keys right/left to select your preferred

language. If the language is available from the provider, this

language will be automatically selected.

6.3.3 Language (Sub-titles)

Sub-titles can be displayed on your screen using this DVB

receiver. If the function Sub-titles is switched on, and the

language selected is being broadcast, these will be automati-

cally displayed.

If the function is not switched on, sub-titles can also be

displayed manually. Sub-titles are indicated by the symbol

shown in the information box. Please also note Point

7.13 of this operating manual.

6.3.4 TV SCART mode

Use the arrow keys right/left to select the appropriate

setting for your TV set,CVBS or RGB. The standard setting

is CVBS.

6.3.5 Video system*

Use the arrow keys right/left to select the appropriate

broadcast standard for your television set. The options avai-

lable are PAL BG, PAL I, PAL DK, SECAM BG and

SECAM DK.

6.3.6 Dolby Digital (AC3)

A number of movies are transmitted in the Dolby Digital for-

mat. This is indicated after a programme has been selected

by the Dolby logo in the information box. If you have

connected a Dolby Digital 5.1 channel amplifier to the

system, you can enjoy movies in 5.1 channel Dolby Digital

sound where available.

* Only for receivers equipped with

this feature

(Fig. 6-5)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 19

To enjoy this feature, you must simply connect the Audio Out

Digital output (see Point 4.5.2) of your DVB receivers with the

digital input of your Dolby Digital 5.1 channel amplifier.

Where a programme is broadcast in Dolby Digital sound, this

will be indicated by the Dolby logo being displayed in the

information window when the programme is selected. If the

function Dolby Digital (AC3) is switched on, these program-

mes will automatically be reproduced in Dolby Digital format.

If the function is not enabled, Dolby Digital sound can also be

switched on manually. Please refer to Point 7.5.1 of this ope-

rating manual.

6.3.7 UHF output channel*

To set a suitable UHF output channel, proceed as follows:

> Select a free UHF channel in the range of 21 to 69 on

your television set.

> Then, using the arrow keys right/left set the new

output channel of your digital receiver. The digital

receiver will now transmit on the UHF channel indica-

ted on the display. If you are not able to obtain interfe-

rence-free reception on this channel, repeat the proce-

dure until you gave found a suitable channel.

> When you have found an optimum UHF channel,

remember to store this in the memory of your televi-

sion set.

> If your television set is equipped only with an automa-

tic programme scan, you will first have to set a random

UHF channel on your digital receiver, and then start

the automatic scan function of your television set. If

necessary, repeat this procedure until you have found

a suitable channel, then store this in the memory of

your television set.

> Finally, it may be necessary to perform some fine

tuning of the channel on your television set.

6.4 Antenna configuration

Once you have completed setting the digital receiver to your

individual preferences, you can proceed, if necessary, to

adjust the digital receiver settings to your antenna. The menu

Antenna Configuration contains the satellites that have

been selected in the installation assistant. If the installation

assistant was interrupted, the satellite positions ASTRA and

EUTELSAT are pre-programmed.

Should you wish to receive other satellites, or if you are using

a different type of LNC, you can adjust your digital receiver to

the appropriate data as follows:

> Press the Menu key to call up the Main Menu.

(Fig.

6-6)

> Use the arrow keys up/down to select the item

Settings.

* Only for receivers equipped with

this feature

(Fig. 6-6)

bed_anl_DVB13 CIP_englisch_q5.qxd 08.09.03 11:14 Seite 20

Page is loading ...

Dolby Laboratories Digital-Satellite-Receiver User manual

Brand: Dolby Laboratories

Model: Digital-Satellite-Receiver

Category: TV set-top boxes

Type: User manual

Download PDF

report

Dolby Laboratories Digital-Satellite-Receiver User manual

Dolby Laboratories Digital-Satellite-Receiver User manual

Other documents