Vaxcel ProLine ow9221w Installation Instructions Manual

Brand: Vaxcel

Model: ProLine ow9221w

Type: Installation Instructions Manual

Vaxcel ProLine ow9221w is an outdoor sensor light with a motion sensor and photocell. It can be mounted on a wall and provides up to 40 feet of detection distance. The light has three modes: " " mode for daytime and nighttime operation, " " mode for nighttime operation only, and Manual Override mode for continuous brightness at night. The shut-off delay can be set from 5 seconds to 3 minutes. The light is also equipped with a gasket to prevent water from seeping into the outlet box.

Sku Number: T0432

T0433

OUTDOOR SENSOR LIGHT

Model Number: ow9221w

ow9222bz

Page 1 of 6

HARDWARE CONTENTS Note: Hardware not shown actual size.

Mounting Screw

Mounting Strip

PACKAGE CONTENTS

Bolt Nut

Mounting Bracket Screw

Wire Connector

Gasket

Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with

package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,

install or operate the product. Contact customer service for replacement parts.

Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters,

Safety Glasses, Ladder, Wire Stripper.

Page 2 of 6

SAFETY INFORMATION

PREPARATION

Important to know

ASSEMBLY INSTRUCTIONS

1. This fixture requires a 120 VAC, 60 Hz power source.

2. For general safety and to avoid any possible damage to the sensor, be sure the power is switched "off" before

adjustment.

3. Motion sensor: turns light ON automatically when motion is detected and turns light OFF automatically when motion

stops.

4. Photocell keeps the light OFF during daylight hours

5. When in manual override mode, use wall switch to keep the light ON during the night.

• All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).

Contact your municipal building department to learn about your local codes, permits and/or inspections.

• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician

before installation.

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

•

Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching

off circuit breaker).

• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact

any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury

or death from electric shock.

CAUTION

Maximum Wattage: 16W

Work Temperature: - 4°F~113°F

Note: Fixture can be wall mounted.

Wall Mounted

Read notes section on page 4-5 for additional

information about mounting location of fixture.

Light fixture and sensor should be mounted as

shown when installed.

Page 3 of 6

ASSEMBLY INSTRUCTIONS (continued)

Installation Steps

1.The fixture mounting bracket is

pre-assembled on the light

fixture (E). Unscrew ball

nuts (C) in order to remove the

mounting bracket.

3. Fixture wires thread through

gasket (EE), and then attach

the gasket (EE) to the back of

mounting bracket.

Pull out the source wires from

the outlet box. Make wire

connections using wire

connectors (FF) as follows:

---Connect the black wire from

the fixture to the “hot” wire

from the power source.

(usually black)

---Connect the white wire from

the fixture to the neutral wire

from the power source.

(usually white)

Carefully tuck the wires back into the outlet box.

Outlet Box

5. Place mounting bracket

against the outlet box,

insert the mounting bracket

screw (DD) through the

mounting bracket hole,

thread mounting bracket

screw (DD) into the center

hole of the mounting strap

(BB). Tighten the mounting

bracket screw (DD)

securely.

NOTE: the “UP” arrow

must point upward.

6. Attach the back plate (D) of

the light fixture (E) to the

mounting bracket, secure it

with the ball nuts (CC).

Mounting Bracket

Gasket

Mounting Bracket

2.Install the mounting strap (BB)

to the outlet box with the

stamped word “FRONT” facing

away from the outlet box, using

two mounting screws (BB) that

best fit the outlet box. Mounting

bracket should sit flush

against wall surface when

secured. (Choose one

matching pair of suitable

mounting screws (AA) from the 3 pairs provided)

Outlet Box

With silicone caulking

compound, caulk completely

around where the mounting

bracket meets the wall surface.

CAUTION: Be sure to caulk completely where the

mounting bracket meets the wall surface to prevent

water from seeping into the outlet box.

Turn off the power at fuse or

circuit box.

Turn on the power at fuse or circuit box.

Adjusting the Sensor Head:

Fig. 1

1. Rotate the sensor head (B) to make the controls show

up. After setting the controls, rotate the sensor head (B)

so the controls are facing the rear of the fixture and the

two dots are in alignment. You can also rotate the

motion sensor left or right to get your desired dection

area. (see Fig.1)

Page 4 of 6

ASSEMBLY INSTRUCTIONS (continued)

Adjusting the Light Head:

1. Gently grasp the light heads and move them up or down, left or right to adjust the

light coverage area. (See Fig. 2)

2. Keep the light heads 30˚ below horizontal to avoid water damage and electrical

shock.

Sensitivity of Motion Sensor:

● You can adjust the sensitivity of the motion sensor by using the “MOTION SENSITIVITY” selector located at

the back of the sensor (See Fig. 3).

Note: Range set too high may increase false triggering.

● Adjust motion sensor sensitivity to achieve desired performance.

● Approximate range for each setting from 20ft to 40ft.

Function and Operation

Note: When power is first applied, the light will turn on. The sensor will take 30 seconds to warm up.

1. “ ” MODE(

daytime and nighttime operation)

●

Turn the knob clockwise to“ ” position, the light turns on

after expiration of the warm-up period, It stays on when

motion is detected. When motion is no longer detected, it

remains on for the predetermined shut-off delay time you

set (5s~3min), and then turns off automatically.

2. “ ” MODE(nighttime operation only)

● Turn the knob counter clockwise to“ ” position, the light

turns on after expiration of the warm-up period, it stays on

when motion is detected. When motion is no longer detected,

it remains on for the predetermined shut-off delay time you

set (5s~3min), and then turns off automatically.

● The light turns off automatically at dawn.

3. Manual Override MODE(nighttime operation only)

● To temporarily override the setting in “ ” mode for

continuous brightness at night, turn the wall switch “OFF”

then turn it “ON” within 3 seconds. The light remains on all

night long. To shift back to “ ” mode, turn the wall switch

“OFF” then turn it “ON” within 3 seconds again.

● The light turns off automatically at dawn.

Note: To make sure the above functions operate properly, always keep the wall switch in the “ON” position

(including the daytime).

Fig. 3

SENSITIVITY

MOTION

SENSITIVITY

TIME

Mode

Manual

Override

Manual Override Operation Diagram

Turn wall switch OFF-ON

in 0.5~3 Seconds

Turn wall switch OFF-ON

in 0.5~3 Seconds

Fig. 4

ASSEMBLY INSTRUCTIONS (continued)

FUNCTION AND OPERATION (continued)

Fig. 2

Page 5 of 6

ASSEMBLY INSTRUCTIONS (continued)

● The shut-off delay is the length of time the light will stay at brightness after motion is detected.

● You can set the shut-off delay by rotating the “TIME” knob arrow so it points to the desired time setting (from 5

seconds to 3 minutes). To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay,

turn the knob counterclockwise.

Shut-off Delay

Customization Options

Notes:

1. The sensitivity of the motion sensor will increase as the

environmental temperature gets cooler. For best

performance, gently clean the lens with a soft cloth every

1 or 2 months to ensure maximum sensitivity.

2. For best performance, install fixture at least 8 feet above

the ground. At such a height, the fixture will provide a

detection distance of up to 40 feet at 77 degrees

Fahrenheit. (See Fig.5)

Fig. 7

3. The sensor detects movement across a detection range

of 180 degrees. (See Fig.6)

4. The sensor will be more sensitive to motion across its

detection path than motion directly towards it. (See Fig.7)

5. To reduce possible nuisances, do not mount the fixture

near a heat source like an air conditioner, vent or furnace

exhaust, or in a direction facing any reflective object or

other nearby light source.

20`

12`

40`

Where you install your fixture is important:

Be sure the light is mounted straight on the wall;

otherwise, the detection distance may be limited.

Fig. 5 Fig. 6

180˚

Motion

Least sensitive

Motion

Most sensitive

Sensor

Fig. 7

FUNCTION AND OPERATION (continued)

Assembly Kit

5347MM (1 SET) FOR T0432

5348MM (1 SET) FOR T0433

The following parts are available for re-order if damaged or missing. Call us toll-free at 1-800-887-6326

Spare Parts List:

Mounting Screw

Mounting Strip

Bolt Nut

Mounting Bracket Screw

Wire Connector

Gasket

Page 6 of 6

TROUBLESHOOTING

CARE AND MAINTENANCE

Clean the glass and coated metal surfaces with a non-abrasive cleaner. Do not use any cleaners with chemicals,

solvents or harsh abrasives, The motion detecting lens is coated with a specially painted finish and requires special

care when cleaning. Use only a soft dry cloth to dust or wipe the lens area.

If unable to fix any of the above issues, please consult a certified electrician.

Troubleshooting

---The light does not come on at all:

1. Make sure the wall switch and circuit breaker are on.

2. Make sure the wiring is correct.

3. Cover the sensor with dark color cloth to verify that the ambient light level is not too high.

---In Manual override, the light stays on after dawn:

1. The ambient light level may be too low due to overcast skies.

Vaxcel ProLine ow9221w Installation Instructions Manual

Brand: Vaxcel

Model: ProLine ow9221w

Type: Installation Instructions Manual

Download PDF

report

Vaxcel ProLine ow9221w Installation Instructions Manual

Vaxcel ProLine ow9221w Installation Instructions Manual

Related papers

Other documents