Lithionics Battery GT Series Installation guide

Type
Installation guide
MiniBMS
OptoLoop
*
Model Numbers
GT12V450A-F24
GT12V600A-F24
GT24V300A-F24
GT48V150A-F24
GT51V150A-F24
GT12V600A-F27
GT24V300A-F27
GT48V150A-F27
GT51V150A-F27
*See Table 1 for model number details
TECHNOLOGY
GT Series Installation Manual
R10 10/23/2019
®
TECHNOLOGY
1 GT Series Installation Manual
Important Safety Guidelines
This guide contains important safety instructions for the GT Series Battery System that must be followed during
installation procedures. Completely read this manual and become familiar with all system components before
attempting installation. Save this installation manual for future reference.
The following symbols and messages are used to identify potential hazards or to clarify the procedure.
The CAUTION symbol indicates a hazardous situation which, if not avoided, could result in moderate or minor injury.
The DANGER symbol indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Safety Information
1. The information in this manual is intended for qualified personnel. Qualified personnel have training,
knowledge, and experience in:
Selecting and using Personal Protective Equipment (PPE).
Installing electrical equipment.
Applying all applicable local and national installation codes.
Analyzing and reducing the hazards involved in performing electrical work.
2. Use of accessories not recommended or sold by the manufacturer may result in a risk of fire, electric shock, or
injury to persons.
3. To avoid a risk of fire and electric shock, make sure that existing wiring is in good condition and that wire is not
undersized. Do not operate the battery system with damaged or substandard wiring.
4. Do not operate the battery system if it has been damaged in any way.
5. This unit does not have any user-serviceable parts. Do not disassemble the battery system except where noted
for connecting wiring and cabling. Attempting to service the unit yourself may result in a risk of electrical shock
or fire. Internal cells remain charged after all power is disconnected.
6. To reduce the chance of short-circuits, always use insulated tools when installing or working with this
equipment.
7. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with electrical
equipment.
2 GT Series Installation Manual
If the system is operated outside of its limits and/or used in combination with non-original components without
authorization, the warranty is void.
Do not expose this unit to direct sunlight, external heat sources or submersion in any liquid. This product is
designed for closed compartment use only. Damage to any part of the battery system caused from direct sunlight,
external heat sources or submersion in any liquid will not be covered by the product warranty.
The Battery Module and BMS is tested to comply with UN DOT 38.3, the testing requirement for Lithium Batteries
per Part III; of the UN Recommendations on the TRANSPORT OF DANGEROUS GOODS (Manual of Tests and Criteria,
Fifth revised edition); [ST/SG/AC.10/11/Rev.5].
This Battery Module contains no mercury and Is RoHS Compliant. Please consult your local municipal authority for
proper disposal.
HAZARD OF ELECTROLYTE VAPOR
The battery module may emit a non-toxic pressurized electrolyte vapor if punctured.
Electrolyte vapor may cause temporary minor breathing congestion.
Electrolyte vapor can decrease visibility in closed compartments.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work
practices.
Always turn OFF all equipment connected to the system in addition to turning OFF the
power switch provided on the system to isolate the batteries from other electrical
circuits, before performing any repairs or maintenance on the system.
Do not operate the system if it has received a sharp blow, been dropped, has cracks or
openings in the enclosure.
Do not disassemble any part of the system. Internal cells remain charged after all power
is disconnected.
Do not operate the system with damaged or substandard wiring.
Always use proper wire sizes to connect the system to inverters, chargers or other
equipment.
Voltage is present at the connector and output terminals. Always ensure that the BMS
output terminals have the insulated protective boots in place.
Always use crimped connections to connect to the output terminals.
Always use a properly rated voltage sensing device to confirm all circuits are de-
energized.
HAZARD OF HEAVY EQUIPMENT
Use two people to lift and mount the battery module.
Always use proper lifting techniques during installation to prevent injury.
Do not lift the battery module by its power or signal wires as they will become
damaged.
3 GT Series Installation Manual
1. System Specifications
1.1 Operating Specifications
Table 1
System Model:
GT12V-450A-
F24-CTRL300
External BMS
GT12V-525A-
F24-CTRL300
External BMS
GT12V-600A-
F24-CTRL300
External BMS
GT24V-300A-
F24-CTRL300
External BMS
GT48V-150A-
F24-CTRL300
External BMS
GT51V-150A-
F24-CTRL300
External BMS
GT12V-600A-
F27-CTRL300
Internal BMS
GT24V-300A-
F27-CTRL300
Internal BMS
GT48V-150A-
F27-CTRL300
Internal BMS
GT51V-150A-
F27-CTRL300
Internal BMS
Capacity 450Ah 525Ah 600Ah 300Ah 150Ah 150Ah 600Ah 300Ah 150Ah 150Ah
Nominal Voltage 12.8V 12.8V 12.8V 25.6V 48.0V 51.2V 12.8V 25.6V 48.0V 51.2V
Recommended Charging
Voltage
14.4V 14.4V 14.4V 28.8V 54.0V 57.6V 14.4V 28.8V 54.0V 57.6V
Overcharge Voltage
Protection
14.8V 14.8V 14.8V 29.6V 55.5V 59.2V 14.8V 29.6V 55.5V 59.2V
Over-discharge Voltage
Protection
11.6V 11.6V 11.6V 23.2V 43.5V 46.4V 11.6V 23.2V 43.5V 46.4V
Standard Charging
Current
150A (C/3) 200A (C/3) 200A (C/3) 100A (C/3) 50A (C/3) 50A (C/3) 200A (C/3) 100A (C/3) 50A (C/3) 50A (C/3)
End of Charging Current 15A (C/30) 20A (C/30) 20A (C/30) 10A (C/30) 5A (C/30) 5A (C/30) 20A (C/30) 10A (C/30) 5A (C/30) 5A (C/30)
Maximum Charging
Current
300A @ 14.2V
Charging
Voltage
300A @ 14.2V
Charging
Voltage
300A @ 14.2V
Charging
Voltage
288A @ 28.4V
Charging
Voltage
144A @
53.25V
Charging
Voltage
144A @ 56.8V
Charging
Voltage
300A @ 14.2V
Charging
Voltage
288A @ 28.4V
Charging
Voltage
144A @
53.25V
Charging
Voltage
144A @ 56.8V
Charging
Voltage
Maximum Charging
Voltage
14.6V @
Standard
Charging
Current
14.6V @
Standard
Charging
Current
14.6V @
Standard
Charging
Current
29.2V @
Standard
Charging
Current
54.75V @
Standard
Charging
Current
58.4V @
Standard
Charging
Current
14.6V @
Standard
Charging
Current
29.2V @
Standard
Charging
Current
54.75V @
Standard
Charging
Current
58.4V @
Standard
Charging
Current
System Impedance at
BMS Power Terminals
2.03 mΩ 1.77 mΩ 2.11 mΩ 1.92 mΩ 5.39 mΩ 5.11 mΩ 2.11 mΩ 1.92 mΩ 5.39 mΩ 5.11 mΩ
Ibf Bolted Fault Current
at Nominal Voltage (N4)
6,305A 7,232A 6,066A 13,333A 8,905A 10,020A 6,066A 13,333A 8,905A 10,020A
Standard Discharging
Current/Load
300A 300A 300A 288A 144A 144A 300A 288A 144A 144A
Maximum Discharge
Current/Load
Maximum Charging
Temperature Range (N1)
Maximum Discharging
Temperature Range (N1)
Module Dimensions
Module Weight (N2) 128lb (58.0kg) 150 (68.2kg) 160lb (72.5kg) 160lb (72.5kg) 152lb (68.9kg) 160lb (72.5kg) 178lb (80.7kg) 178lb (80.7kg) 170lb (77.1kg) 178lb (80.7kg)
BMS Case Dimensions
(N3)
BMS Weight (N2)
-4 to 131°F (-20 to 55°C)
300A
7.7lb (3.5kg)
N/A
N/A
11.25" x 6.96" x 4.1" (286 x 177 x 104mm)
27.0" x 16.0" x 11.1" (686 x 406 x 282mm)
24.0" x 13.0" x 11.1" (610 x 330 x 282mm)
32 to 11F (0 to 45°C)
Notes for Table 1:
(N1) Maximum charging and discharging rates apply depending upon the ambient temperature and duty cycle of the system. UL1973 tests of maximum
charge and discharge current were performed at 25°C/77°F.
(N2) Does not include 4/0 power cable’s weight as its length varies per application.
(N3) Does not include 4/0 power cable, main power connector, or terminals. Please see www.lithionicsbattery.com for dimensions.
(N4) "Bolted Fault Current" per NFPA-70E.
4 GT Series Installation Manual
1.2 Arc Flash Energy Specifications
An arc flash is the light and heat produced from an electric arc supplied with sufficient electrical energy to cause
substantial damage, harm, fire, or injury.
o An example of an arc flash event could be a direct short circuit caused by a metallic object such as a tool bridging
between the positive and negative of an energized circuit.
o Table 2 below quantifies the hazard level of arc flash energy that each battery system is capable of producing.
Per NFPA 70E D.5.1 "Maximum Power Method"
Iarc = 0.5 x Ibf
IEm = 0.01*Vsys* Iarc*Tarc/D
2
(Arc Flash Energy)
Calculations are for a maximum of six modules in parallel connection.
Table 2
Configuration Vsys
Impedance mΩ
Ibf, calc. Iarc IEm cal/cm^2 3x IEm cal/cm^2
Distance where
IEm=1.2 (Arc
Boundary), inches.
Hazard level
GT12V450 12.8 0.34 37833 18916 0.082 0.246 4 0
GT12V525 12.8 0.3 43390 21695 0.094 0.282 5 0
GT12V600 12.8 0.35 36398 18199 0.079 0.236 4 0
GT24V300 25.6 0.32 80000 40000 0.346 1.039 9 0
GT48V150 48 0.9 53432 26716 0.434 1.301 10 0
GT51V150 51.2 0.85 60117 30059 0.52 1.561 11 0
Tarc= 70mS
fuse clearing
time
Hazard/risk classification as per NFPA 70E-2000
1.3 Manufacturing Date Code Format
MMDDYYYY001
o MM: Month of Manufacture
o DD: Day of that Month
o YYYY: Year of Manufacture
o 001: Sequence of Battery Produced on That Day
Example: 01012018001 = manufactured on January 1, 2018 and it was the first battery produced on that day.
5 GT Series Installation Manual
2. System Installation
2.1 Short Circuit Protection
The battery system must be protected by a 300A fast acting DC fuse, for example:
o Fuse: Eaton DFJ-300
o Fuse holder: Eaton JM60400-1CR-1
o Fuse placement must be directly after the positive power terminal on the BMS. (Fuse placement may be controlled
by other industry standards such as ABYC or RVIA.)
2.2 Disconnect Device Protection (only applies to GT51V150A system)
Per UL1973 Revision 2 Section 7.8.1.4, the GT51V150A system must have 2 additional disconnect devices, one
located on the positive pole and one on the negative pole.
o The disconnect devices shall not require the use of special tools or equipment to be operated.
o Recommended disconnect device: Gigavac HBD41 Hermetic Battery Disconnect.
o Please see Figure 1 for the disconnect devices placement.
2.3 Battery Module and NeverDie BMS Unit Environment and Mounting orientation
The Battery Module and BMS Unit should be mounted in an environment that does not receive direct sunlight,
pressurized water or road debris.
To avoid power interruption, your installation may need to consider controlling the ambient operating temperature.
Mount the Battery Module in an upright position, i.e. black lid faces up.
o Other orientations are NOT permitted and will void the warranty.
The BMS Unit can be mounted in any orientation as long as all its features are accessible.
Ensure that the BMS Unit is located in close proximity to the Battery Module so that all connectors can be mated in
the following steps.
2.4 Temperature Sensor Connector
The temperature sensor cable and connector exiting the battery module must be connected to the BMS.
Connect the two M8 circular connectors together by first aligning their pins and pressing them together, then rotate
the securing nuts until they stop snugly.
Do not use the temperature probe from the inverter-charger manufacturer.
2.5 Main Power Connector
The battery module has a large black female main power connector that must be inserted into the BMS’ male main
power connector. This is the connector with the large 4/0 red and black wires and single small gauge gray cable.
Align the connectors and insert them together.
Use 2 zip ties to bind the connectors together so that they may not separate during use.
2.6 NeverDie BMS Unit Power Terminals
Connect the BMS Unit Power Terminals to your DC bus, both Positive (Red) and negative (Black).
o Use correctly sized wire conductors for the application.
o Torque to 80 INCH pounds
o Never stack ring terminals.
o Never place the stainless-steel washer between the Power Terminal and ring terminal lug (see Figure 1 on Page 7).
2.7 Pressure Vent
It is recommended to install a ventilation hose onto the pressure vent barb when the Battery Module is in a location
with poor ventilation.
o The hose shall direct the gases to the atmosphere.
6 GT Series Installation Manual
2.8 BMS Unit I/O Connector
Some systems have a rectangular I/O connector to extend the BMS Unit features remotely such as remote
Power/Reset switch, LED indicator, or serial datalogging. Be sure to connect the I/O connector if so equipped.
2.9 Initial Charge Cycle
Initially the system must be FULLY charged once to calibrate the BMS Unit to the Battery Module. Please read and
follow the next section to perform this.
7 GT Series Installation Manual
3. System Operation
3.1 Powering the System On
Press the momentary Power/Reset switch for 1 second.
o The switch will illuminate once power is enabled.
o You may notice an audible “thunk” noise of the internal contactor switching on.
o Check that there is voltage at the Power Terminals with a voltmeter.
3.2 Powering the System Off
Press and hold the momentary Power/Reset switch for 3 seconds.
o The switch will cease to illuminate once power is disabled.
o You may notice an audible “thunk” noise of the internal contactor switching off.
o Check that there is 0V at the output terminals with a voltmeter.
3.3 Charging
The charging device(s) connected to the GT Series Lithium Battery System must be programmed as per Table 1.
Charging may be performed at any time the system is powered On.
o NOTE - The GT Series Lithium Battery System will disconnect power if the voltage, amperage, or temperature limits
are exceeded during charging.
o Only use a Lithionics Battery approved charging source. Please contact Lithionics Battery for charger approval.
3.4 Initial Charging Cycle
The initial charging cycle is required as it calibrates the NeverDie BMS to the Battery Module for accurate State of
Charge percentage (SoC) monitoring.
During the initial charging cycle the system must reach a voltage level that is equal to the Standard Full Charging
Voltage indicated in Table 1.
Enable the charging device(s) so that they may complete a charge cycle. It is recommended to not have any discharge
loads active during the initial charging cycle, especially towards the end of charging.
3.5 Discharging
Discharging may be performed at any time the system is powered On.
o NOTE - The GT Series Lithium Battery System will disconnect power if the voltage, amperage, or temperature limits
are exceeded during discharging.
The NeverDie feature allows the system to have a “reserve” amount of energy left in the battery. Once the system is
discharged to 12.0V or 10% State of Charge (SoC), whichever comes first, power will be disabled to leave a “reserve”
amount of energy still left in the battery.
To enable the remaining reserve energy of the system, press the momentary Power/Reset switch for 1 second.
o NOTE - Once the reserve range is enabled the battery should be charged as soon as possible.
o WARNING - If the reserve energy is used and the battery module is left in a deeply discharged state without
immediate charging, the battery module will become permanently damaged.
3.6 System Storage Procedure
8 GT Series Installation Manual
Storing your battery at the correct specifications is important as it keeps the battery in the healthiest state possible
for the fastest deployment when needed.
If the GT Series Lithium Battery System will not be in use for greater than 2 weeks, it is recommended to enable
system storage.
Storage mode is simply a fully charged system in the Powered Off state.
To enable System Storage:
o Perform a full charge cycle, ensure that the System voltage reaches the Standard Full Charging Voltage indicated in
Table 1.
o Power off the System, press and hold the Power/Reset switch for 3 seconds. Check that the switch is no longer
illuminated. Check that there is 0V at the Power Terminals with a voltmeter.
Table 3
Storage
Temperature &
Humidity Range
< 1 Month
-4~95°F (-20~35°C), 45~75%RH
< 3 Months
14~86°F (-10~30°C), 45~75%RH
Long Term Storage
If the battery needs to be stored for > 3 months the voltage should be 13.2V for
a 12V battery (or 3.3V x number of cells in series) (~50%SOC) and stored at the
recommended storage specifications shown above. Additionally, the battery
needs at least one charge-discharge-recharge to 50% SOC cycle every six
months.
Self-discharge rate
≤3% per month
Storage conditions < 3 months:
1. Fully charge the battery.
2. Turn the battery OFF by the Power/Reset switch.
3. Store the battery in an environment according to the specifications shown above.
Storage conditions > 3 months:
1. Reduce the battery SOC to 3.3V/cell which is 50% ±10% SOC.
NOTE - See table 4 below for voltage calculation.
2. Turn the battery OFF via the Power/Reset switch.
3. Store the battery in an environment according to the specifications shown in table 3 above.
4. Every 6 months charge the battery to 100% SOC, then discharge the battery to LVC, then charge it to 50% ±10%
SOC.
Table 4
Battery
Voltage
Number of
Cells
~50% SOC
Voltage
12V
4
13.2
24V
8
26.4
48V
15
49.5
51V
16
52.8
NOTE For further system installation and operation please refer to the Advanced Series User Guide available at:
http://www.lithionicsbattery.com/user-guides/
9 GT Series Installation Manual
Figure 1: System Example
NeverDie
BMS
Main Power
Connectors
Temperature
Sensor
Connectors
Battery
Module
Pressure
Vent
300A Fast
Acting Fuse
Disconnect
Devices
(See section 2.2 -
Only applies to
GT51V150A system)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Lithionics Battery GT Series Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI