RJX Hobby VECTRON Assembly Manual

Assembly Manual V1.0

VECTRON

ca. 301mm

ca. 983mm

ca.156,5mm

TECHNICAL DETAILS

: ca. 1117mm (500mm Blades)

: ca. 204 - 224mm (70-80mm Tail Blades)

: 5.9/11 (30T/16T Motor Pinion)

: 1 : 4.69

: 2600g - 2800g (depending Setup)

: 6S 3300mAh - 5300mAh

: 51.5mm (0) x 50mm (h)

/

Page 1

Main Rotor Diameter

Tail Rotor Diameter

Gear Ratio

Tail Gear Ratio

Total RTF Weight

Lipos

Max. Motor Size

Assembly Manual of the RJX VECTRON 520

For the correct assembly and safe flying of your

RJX VECTRON 520 Model, this manual uses this symbol

where special attention is required. Failing to carry out the

instructions at this point in the assembly will result in an

electronic and/or mechanical failure or possible injury.

HOW TO USE THIS INSTRUCTION MANUAL

This manual contains the detailed instructions to build and set

up the RJX VECTRON 520. Please follow it to ensure that you

achieve the best performance and mechanical integrity from

your finished kit.

For those of you who already have experience with model

helicopters, we strongly suggest that you assemble and

adjust your model according to these instructions for the

best results. Please keep this manual in a safe place and

refer to it when replacing spare parts or upgrading.

DISCLAIMER

While every effort has been made to supply the proper

information in this manual, the Manufacturer and Distributor

cannot guarantee that the consumer will interpret or follow

these instructions as intended and therefore the Manufacturer

and Distributor cannot assume any liability for damage or

claims occurring from the misuse of our product.

This product is intended for advanced users. It may look easy

when watching an experienced pilot flying his model, but it

takes dedication and numerous hours of practice to be able to

operate this model safely and efficiently.

Beginners are encouraged to seek help from an experienced

pilot to assist in the first test flights. We encourage you to

practice frequently and enjoy the experience of RC rotary

flight!

WARNING

LiPo batteries need special care. Improper storage, handling

or charging may cause fire or damage your Helicopter and

possibly to yourself. Contact your dealer or supplier for more

information.

1. Check your charger settings before charging your LiPo

battery to insure they are correct for the specifications

of the battery.

2. We recommend storing and charging LiPo batteries in

a Lipo sack or porcelain container. If kept in a metal

container or ammo case, the batteries may explode if

the storage containers are sealed and the gases are

not able to vent. We recommend using the original Lipo

Sack from the USA since it was designed to contain

the jet flames discharged from a failing Lipo battery.

3. Please keep LiPo Batteries away from sources of heat.

4. Never store LiPo Batteries fully charged.

5. NEVER SHORT OUT LiPo Battery wires.

6. Before connecting your LiPo battery to the Helicopter,

make sure your transmitter is turned ON and all sticks

and switches are set properly.

Page 2

IMPORTANT

TO PREVENT LOOSE SCREWS AND BOLTS

Regardless how tightly nuts, bolts and screws are tightened,

they slowly loosen over time due to vibration of the helicopter.

Should this happen, you will lose control of the helicopter

which may cause severe damages or very potential dangerous

situation.

We strongly recommend that you apply thread lock to any

nuts, bolts or screws. There are two types of thread lock, blue

(medium) and red (hard).

 Clean the nuts, bolts and screws with Alcohol (or

similar) before you apply the thread lock.

 Use blue thread lock on screws that have to be

removed regularly, and

 Red thread lock for screws that should be fixed

permanently.

1. Use CA: (Super glue or similar) at this point

2. LOCTITE 243 ( ) - LOCTITE 648 ( ):

Remove oil and grease then apply shown thread lock.

(This applies throughout the manual)

3. GREASE: Remove oil and grease. (This applies

throughout the manual)

Items required to complete the RJX VECTOR 700

- CCPM compatible PCM or 2,4 Ghz Radio System with 4 x

MIDI Servo

- 3 Axis Virtual Fly bar System

- A 890 kV Brushless Out runner Motor with 5 mm Motor shaft

(if not included)

- LiPo Pack 6S-4500 up to 5300 mAh (depending on setup)

- 100A ESC (if not included)

- CF FBL Main Blades 500 mm (if not includecd)

- LiPo Charger

Tools required (not included)

- Allen Drivers 15 mm - 2 mm - 2,5 mm - 3 mm - 4 mm

- Philips Drivers large - middle - small

- Nut Drivers 4,5 mm - 5,5 mm - 7 mm

- Cutter

- Universal Pliers

- Scissors

- Sandpaper

- Ball Link Plier

- Metric Ruler

- Pitch Gauge digital

- Cyanoacrylate (CA - Superglue)

- Grease

- Ball Link Driver

- EPOXY

Page 3

IMPORTANT

BLUE

RED

ROTORHEAD ASSEMBLY (BAG 1.1)

M2,5x8

VT70201

VT70508

VT61105

(2x Bearing 6x12x4)

M2,5x6

M3x10

W3x10x1,5

VT61106

VT70510 (W6x10x1,5)

VT61104

VT61107

Small ID outside

Large ID inside

Grease

Page 4

VT70504

(W9x12x0.8)

VT81047

(Thrust Bearing F5-12M)

ROTOR HEAD ASSEMBLY (BAG 1.2)

4x VT70201

3x VT70148

Swashlock Linkage

Pin 14mm x 2mm

VT60249

Assemble 2 Sets

Page 5

VT61110

2x C-Clip

VT60249

(2x Bearing F3x7x3)

ROTOR HEAD ASSEMBLY (BAG 1.3)

Locknut M2,5

2x M3x16

VT61115

Page 6

M2,5x16

W3x5x1

MAINFRAME ASSEMBLY (BAG 1.4)

2x M2,5x8

VT1015

VT60522U

Page 7

(Bearing F8x15x5)

MAINFRAME ASSEMBLY (BAG 2.1)

4x M3x6

4x M3x6 Counter Sunk Screw

VT61090

VT61113

Page 8

VT61091

VT61112

VT61074

(Bearing HF1012,2x 10x15x4)

MAINFRAME ASSEMBLY (BAG 2.4)

12x M2.5x6

VT61082

Page 9

VT60522L

VT60733

(Bearing F8x16x5,F6x13x5)

MAINFRAME ASSEMBLY (BAG 2.5)

Page 10

5x M2,5x6

5x VT70020

MAINFRAME ASSEMBLY (BAG 2.5)

Page 11

M3x8

W3x8x1

VT60007

(S3M16T)

M2.5x6

VT70506

VT60503

(Bearing 4x9x4)

MAINFRAME ASSEMBLY (BAG 2.5)

VT5010

VT50002

VT50003

Page 12

Page 13

MAINFRAME ASSEMBLY (BAG 2.6)

19x M2,5x6

MAINFRAME ASSEMBLY (BAG 6)

Page 14

M3x8

0 Play

M2.5x8

VT70008

M3x16

VT8000

MAINFRAME ASSEMBLY (BAG 6)

Page 15

4x M2,5x6

2x VT60339

MAINFRAME ASSEMBLY (BAG 6)

Page 16

8x M2.5 Locknut

8x M2.5x12

2x VT60340B

2x VT60340C

2x VT60340A

TAIL ASSEMBLY (BAG 3.1)

VT70028

VT60058

VT60057

M2x6

Jointball

VT60055

(S3M16T)

VT70027

(65,5MM)

VT60862

(2X F5X10X4)

2x M2,5x8

M2x6

Jointball

VT83095

VT9023

(W3X5X3)

XT8068

(W3X5X2)

M3x4 Set Screw

12mm Pin

VT60054

M3x25

V60054

2x M3x10

TAIL ASSEMBLY (BAG 3.2)

2x M4x4 Set Screw

2x Jointball

2x M2x10

2x XT90-9003A

(W7x10x0.5)

2x F5-10M

5x10x4

Thrustbearing

2x W3x8x1

2x XT90-60528A

X800-60222

Small ID outside

Large ID inside

Grease

VT60528

TAIL ASSEMBLY (BAG 3.3)

VT83091

(580MM)

VT60866

Vt9032

4x M3x8

S3M1299

VT61118

M2x10

M2 Nut

Page is loading ...

RJX Hobby VECTRON Assembly Manual

RJX Hobby VECTRON Assembly Manual

Other documents