Fujitsu AUG45ALB3W Installation guide

Brand: Fujitsu

Model: AUG45ALB3W

Category: Split-system air conditioners

Type: Installation guide

This manual is also suitable for

INDOOR UNIT (Cassette Type)

INSTALLATION MANUAL

For authorized service personnel only.

AIR CONDITIONER

English

PART No. 9363217094

Refer to the rating label with the serial number.

MADE IN THAILAND

9363217094_IM_EN.indd 1 3/15/2018 15:50:40

En-1

1. SAFETY PRECAUTIONS

WARNING!

This mark indicates procedures which, if improperly performed,

might lead to the death or serious injury of the user.

CAUTION!

This mark indicates procedures which, if improperly performed,

might possibly result in personal harm to the user, or damage

to property.

WARNING

For the air conditioner to operate satisfactorily, install it as outlined in this

installation instruction sheet.

Connect the indoor unit and outdoor unit with the room air conditioner piping

and cords available from our standard parts. This installation instruction sheet

describes the correct connections using the installation set available from our

standard parts.

Installation work must be performed in accordance with national wiring

standards by authorized personnel only.

If refrigerant leaks while work is being carried out, ventilate the area. If the

refrigerant comes in contact with a ame, it produces a toxic gas.

Do not turn on the power until all installation work is complete.

During installation, make sure that the refrigerant pipe is attached rmly before

you run the compressor.

Do not operate the compressor under the condition of refrigerant piping not attached

properly with 2-way or 3-way valve open. This may cause abnormal pressure in the

refrigeration cycle that leads to breakage and even injury.

During the pump-down operation, make sure that the compressor is turned off

before you remove the refrigerant piping.

Do not remove the connection pipe while the compressor is in operation with 2-way or

3-way valve open. This may cause abnormal pressure in the refrigeration cycle that

leads to breakage and even injury.

When installing and relocating the air conditioner, do not mix gases other than

the specied refrigerant (R22) to enter the refrigerant cycle.

If air or other gas enters the refrigerant cycle, the pressure inside the cycle will rise to

an abnormally high value and cause breakage, injury, etc.

•Be careful not to scratch the air conditioner when handling it.

•After installation, explain correct operation to the customer, using the operating manual.

•Let the customer keep this installation instruction sheet because it is used when the air

conditioner is serviced or moved.

•The maximum length of the piping is shown in Table 1. If the units are further apart than

this, correct operation cannot be guaranteed.

2. ABOUT THIS PRODUCT

2. 1. Accessories

INDOOR UNIT ACCESSORIES

Name and Shape Q’ty Description

Operating Manual

Installation manual

(This book)

Coupler heat insulation

For indoor side pipe joint

Special nut A

(largeange)

For installing indoor unit

Special nut B

(smallange)

For installing indoor unit

Template

For ceiling hole cutting

Binder

(large)

For remote controller cable binding

Blower cover insulation

For discharged air

Hook wire

For installing intake grille

REMOTE CONTROLLER ACCESSORIES

Name and Shape Q’ty Description

Remote controller

Installation to indoor unit

Remote controller cable

For connecting the remote controller

Remote controller cord clamp

For installing the remote controller

cord

Screw

For installing the remote controller

cord clamp

For installing the remote controller

Binder

For remote controller and remote

controller cable binding

OUTDOOR UNIT ACCESSORIES

Q’ty

Power cap

For power supply cord installation

Auxiliary pipe assembly

For wiring conduit (gas side) connec-

tion (May not be supplied, depending

on the model)

Edge cover

For wiring conduit installation hole

edge protection

Tapping screw

•For cabinet A and cabinet D

mounting (1)

•Spare (1)

Binder

For power supply cord binding

Putty

For sealing

1. SAFETY PRECAUTIONS ……………………………………………………………… 1

2. ABOUT THIS PRODUCT ………………………………………………………………… 1

2.1. Accessories ………………………………………………………………………… 1

3. GENERAL SPECIFICATION …………………………………………………………… 2

3.1. Pipe requirement …………………………………………………………………… 2

3.2. Electrical requirement ……………………………………………………………… 2

4. INSTALLATION WORK ………………………………………………………………… 2

4.1. Selecting an installation location ………………………………………………… 2

4.2. Indoor unit installation ……………………………………………………………… 3

4.3. Installing the drain pipe …………………………………………………………… 5

4.4. Outdoor unit installation …………………………………………………………… 5

5. PIPE INSTALLATION …………………………………………………………………… 6

5.1. Flare processing …………………………………………………………………… 6

5.2. Bending pipes ……………………………………………………………………… 6

5.3. Connection pipes …………………………………………………………………… 6

5.4. Vacuum process …………………………………………………………………… 7

5.5. Installing the coupler heat insulation ……………………………………………… 7

6. ELECTRICAL WIRING …………………………………………………………………… 8

7. GRILLE INSTALLATION ………………………………………………………………… 9

8. POWER ………………………………………………………………………………… 10

9. REMOTE CONTROLLER INSTALLATION ………………………………………… 10

9.1. Electrical requirement …………………………………………………………… 10

9.2. Dimensions ……………………………………………………………………… 10

9.3. Name of parts …………………………………………………………………… 11

9.4. Installation ………………………………………………………………………… 11

9.5. Setting the DIP switch …………………………………………………………… 12

9.6. Connection of Remote Controller Cable ……………………………………… 12

10. SPECIAL INSTALLATION METHODS ……………………………………………… 12

10.1. Group control …………………………………………………………………… 12

10.2. Auto restart ……………………………………………………………………… 13

10.3. Memory backup function ………………………………………………………… 13

11. TEST RUN ……………………………………………………………………………… 13

12. OPENING THE DUCT CONNECTION HOLE ……………………………………… 14

13. CUSTOMER GUIDANCE ……………………………………………………………… 14

INSTALLATION MANUAL

PART No. 9363217094

Indoor Unit (Cassette Type)

Contents

Note: This manual describes how to install the air conditioner described above. Handling

and installation shall only be done by professionals as outlined in this manual.

9363217094_IM_EN.indd 1 3/15/2018 15:50:42

En-2

Q’ty

Coupler heat insulation

For outdoor side pipe joint

Pipe (drain)

For outdoor unit drain piping work

(May not be supplied, depending on

the model.)

Flexible tube

Cap (drain)

3. GENERAL SPECIFICATION

3. 1. Pipe requirement

Table 1

Diameter

Maximum length

Maximum height

(between indoor and

outdoor)

Small Large

9.53 mm

(3/8")

19.05 mm

(3/4")

50 m

(164 ft)

30 m

(99 ft)

•Use 0.7 mm to 1.2 mm thick pipe.

•Use pipe with water-resistant heat insulation.

•Use pipe that can withstand a pressure of 3,040 kPa.

3. 2. Electrical requirement

•Electric wire size and fuse/breaker capacity:

Table 2

Power supply cable

(mm

)

MAX 4.0*2

MIN 2.5*1

Connection cable

(mm

)

MAX 2.5*1

MIN 1.0*1

Fuse/Breaker capacity (A) 20

•Use conformed cord with Type 245 IEC57 (*1) or Type 245 IEC66 (*2).

•Install all electrical works in accordance to the standard.

•Install the disconnect device with a contact gap of at least 3 mm in all poles nearby the

units. (Both indoor unit and outdoor unit)

4. INSTALLATION WORK

4. 1. Selecting an installation location

Especially, the installation place is very important for the split type air conditioner because

itisverydifculttomovefromplacetoplaceaftertherstinstallation.

Decide the mounting position together with the customer as follows:

The discharge direction can be selected as shown below.

Fig. 1

100 mm (4") or more

Piping position

100 mm (4")

or more

(4 directions) (3 directions) (2 directions) (2 directions)

100 mm (4") or more

1,000 mm (39")

or more

CAUTION

Since 2-way outlet as shown below causes performance problems, do not set it.

Pipe

INDOOR UNIT

(1) Installtheindoorunitonaplacehavingasufcientstrengthsothatitwithstands

against the weight of the indoor unit.

(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all

over the room.

(3) Leave the space required to service the air conditioner (Fig. 2).

(4) The ceiling rear height as shown in Fig. 3.

(5) A place from where the air can be distributed evenly throughout the room by the unit.

(6) A place from where drainage can be extracted outdoors easily.

(7) Installtheunitwherenoiseandvibrationsarenotamplied.

Fig. 2

Strong and durable ceiling

2,700 mm (106")

or more

1,000 mm (39")

or more

Obstruction

This mechanism enables the cassette body to move 35 mm downward and realizes instal-

lation to the space of 250 mm. No special works and option is needed.

Fig. 3

You can select 2-way setting

(A) Standard setting (B) Slender setting

285 mm (11-7/32")

or more

250 mm (9-27/32")

or more

OUTDOOR UNIT

WARNING

Install the unit where it will not be tilted by more than 5°.

When installing the outdoor unit where it may exposed to strong wind, fasten it se-

curely.

(1) Leavethespacesindicatedforgoodairow(Fig.4).

Fig. 4

10 mm (0.4")

or more

300 mm (12")

or more

600 mm (24")

or more

100 mm (4")

or more

(2) If possible, do not install the unit where it will exposed to direct sunlight. (If necessary,

installablindthatdoesnotinterferewiththeairow.)

(3) Donotinstalltheunitnearasourceofheat,steam,ofammablegas.

(4) Duringheatingoperation,drainwaterowsfromtheoutdoorunit.Therefore,install

theoutdoorunitinaplacewherethedrainwaterowwillnotbeobstructed.(Reverse

cycle model only.)

(5) Do not install the unit where a strong wind blows or where it is very dusty.

(6) Do not install the unit where people pass.

(7) Install the outdoor unit in a place where it will be free from being dirty or getting wet by

rain as much as possible.

(8) Install the unit when connection to the indoor unit is easy.

9363217094_IM_EN.indd 2 3/15/2018 15:50:43

En-3

REMOVING THE PANEL FRAME

• Pull up the corner sections (A) of the panel frame as shown in Fig. 9 (4 locations).

Fig. 9 Part A detail view

• Pull up in the direction of the arrow while holding down the C section of Fig. 10 (4 loca-

tions).

Fig. 10 Part B detail view

Fig. 11

Panel frame

Panel base

CAUTION

Always remove the panel frame after removing the intake grille.

4. 2. Indoor unit installation

WARNING

Install the airconditioner in a location which can withstand a load do at least ve

times the weight of the main unit and which will not amplify sound or vibration.

If the installation location is not strong enough, the indoor unit may fall and cause inju-

ries.

If the job is done with the panel frame only, there is a risk that the unit will come loose.

Please take care.

REMOVING THE INTAKE GRILLE

(1) Push the intake grille pushbuttons (two places).

(2) Open the intake grille.

Fig. 5

Push

Open

(3) Remove the grille hinge wire.

Fig. 6

• Pull up while pressing the B section (Fig. 7).

Fig. 7 Part A detail view

Fig. 8 Part A section view

Grille hinge wire

(4) Remove the intake grille.

9363217094_IM_EN.indd 3 3/15/2018 15:50:44

En-4

1. POSITION THE CEILING HOLE AND HANGING BOLTS

Fig. 12

940 mm ( 37")

750 mm (29-17/32")

(Hanging bolt position)

890 mm ( 35-3/64")

(Ceiling opening measurement)

(Hanging bolt position)

(Grille measurement)

2. HANGING PREPARATIONS

• Firmly fasten the hanging bolts as shown in Fig. 13 or by another method.

• Install the hanging bolts at a place where they would be capable of holding a weight of

at least 50 kgf per bolt.

Fig. 13

Hole-in anchor

Hole-in plug

Hanging bolt

M10

Concrete

Insert

Fig. 14

(A) Standard setting

298.5 mm (11-3/4")

305.5 mm (12")

Drain pipe (I.D. 32 mm)

248.5 mm

(9-25/32")

60 mm

(2-3/8")

(4-23/32")

(5-29/32")

(5")

120 mm

150 mm

285 mm (11-7/32")

127 mm

(B) Slender setting

298.5 mm (11-3/4")

305.5 mm (12")

Drain pipe (I.D. 32 mm)

248.5 mm

(9-25/32")

60 mm

(2-3/8")

(4-23/32")

(5-29/32")

(3-5/8")

120 mm

150 mm

250 mm (9-27/32")

92 mm

3. BODY INSTALLATION

[The ceiling rear height is 285 mm (11-7/32") or more.] [Standard setting]

[The ceiling rear height is 250 mm (9-27/32") or more.] [Slender setting]

(1) Install special nut A, then special nut B onto the hanging bolt (Fig. 15).

(2) Raise the body and mount its hooks onto the hanging bolt between the special nuts

(Fig. 15).

(3) Turn special nut B to adjust the height of the body (Fig. 15).

(4) Leveling

 Usingalevel,orvinylhoselledwithwater,neadjustsothatthebodyislevel.

WARNING

Performnaltighteningbytighteningthedoublenutrmly.

Fig. 15

Special nut A

Ceiling

*Mustttightlyagainst

ceiling without any gap.

Special nut B

Hanging bolt

Hook

30 mm

or more

After installing the body,

tighten the nuts.

Fig. 16

Vinyl hose

* Allowable space between

the unit and the ceiling

5 mm or less

INSTALLING THE PANEL FRAME

Fig. 17

Panel base

Panel frame

*90° Turn

* With slender setting, turn the panel frame 90° as shown in the diagram above.

Grille setting method has been changed at the marked positions on the panel frame and

panel base.

9363217094_IM_EN.indd 4 3/15/2018 15:50:45

En-5

Fig. 18

(A) Standard setting (B) Slender setting

Mark

Panel frame

No mark

Fig. 19

[Example]

* Appearance of slender setting

4. 3. Installing the drain pipe

CAUTION

Install the drain pipe in accordance with the instructions in this installation instruction

sheet and keep the area warm enough to prevent condensation. Problems with the

piping may lead to water leaks.

Notes: Install the drain pipe.

•Install the drain pipe with downward gradient (1/50 to 1/100) and so there are no rises or

traps in the pipe.

•Use general hard polyvinyl chloride pipe (VP25) [outside diameter 32 mm (1-1/4")] and

connect it with adhesive (polyvinyl chloride) so that there is no leakage.

•When the pipe is long, install supporters.

•Do not perform air bleeding.

•Always heat insulate the indoor side of the drain pipe.

•When desiring a high drain pipe height, raise it up to 800 mm (31") or less from the

ceiling within a range of 150 mm (6") from the body. A rise dimension over this range will

cause leakage.

Fig. 20

Air bleeding

150 mm (6") or less

1.5 to 2 m (5 to 6.5 ft)

Supporter

Max 800 mm

(31")

Rise

Trap

4. 4. Outdoor unit installation

1. OUTDOOR UNIT PROCESSING

(1) When the outdoor unit will be exposed to strong wind, fasten it with bolts or wire at the

four places indicated by the arrows (Fig. 21).

(2) Sincethedrainwaterowsoutoftheoutdoorunitduringheatingoperation,install

the drain pipe and connect it to an commercial 16 mm hose. (When heating when the

outdoor temperature is 0 C or less, construct so that the drain water drained from the

outdoor unit will not freeze in the drain pipe.)

(3) When installing the drain pipe, plug all the holes other than the drain pipe mounting

hole in the bottom of the outdoor unit with putty so there is no water leakage (Fig. 21).

Fig. 21

Drain cap (2) Drain cap (2)

Ø12 hole (anchor bolt M10)

650 mm (25-19/32")

400 mm (15-3/4")

Bottom

Drain pipe

mounting hole

Drain

pipe

(4) Always use a drain pipe at two places.

2. OUTDOOR UNIT CONNECTION CORD AND PIPE CONNECTION

PREPARATIONS

(1) Piping and connection cord mounting direction (4-way mounting possible).

Fig. 22

Cabinet A

Rear piping

Right piping

Bottom piping

Front piping

(2) Remove outdoor unit cabinet A and cabinet D.

Fig. 23

Valve

Cabinet D

Cabinet A mounting

direction

* Use the accessory screws at these points only.

* After removing the screws, remove

cabinet A by pushing it down.

9363217094_IM_EN.indd 5 3/15/2018 15:50:46

En-6

(3) Open the piping and connection cord knockout holes of the desired direction with

nippers, etc. After opening the knockout holes, install the accessory edge cover and

power cap to protect the opened places.

Fig. 24

Connection cord

(Indoor unit and

outdoor unit

connection cord)

Knockout hole

Cabinet D

Edge cover

Pipe mounting hole

Pipe

Power cap

(Power supply cord mounting hole)

Power supply cord

(4) Connect the piping and power supply cord from the mounting holes.

Fig. 25

(Example)

* When pipe bending work is

difcultinsidetheoutdoor

unit, use the accessory

auxiliary pipe assembly.

Auxiliary pipe assembly

Coupler heat insulation

5. PIPE INSTALLATION

5. 1. Flare processing

(1) Cut the connection pipe with pipe cutters so that the pipe is not deformed.

(2) Holding the pipe downward so that cuttings cannot enter the pipe and remove the

burrs.

(3) Removethearenutfromtheindoorunitpipeandoutdoorunitandassembleas

shownin(Table3)andinsertthearenutontothepipe,andarewithaaringtool.

(4) Checkifthearedpart“L”(Fig.26)isspreaduniformlyandthattherearenocracks.

Table 3

Pipe Flare nut

Small pipe Small(widthacrossats22mm)

Large pipe Large(widthacrossats36mm)

Fig. 26

L dimension

Small pipe (9.53 mm dia.)

1.8 to 2.0 mm

Large pipe (19.05 mm dia.)

2.6 to 3.0 mm

Widthacrossats

5. 2. Bending pipes

The pipes are shaped by your hands. Be careful not to collapse them.

Fig. 27

Good

Extend the pipe

by unwinding it.

Bad

Do not bend the pipes in an angle more than 90°.

Whenpipesarerepeatedlybentorstretched,thematerialwillharden,makingitdifcultto

bend or stretch them any more. Do not bend or stretch the pipes more than three times.

When bending the pipe, do not bend it as is.

The pipe will be collapsed. In this case, cut

the heat insulating pipe with a sharp cutter

as shown in Fig. 28, and bend it after expos-

ing the pipe. After bending the pipe as you

want, be sure to put the heat insulating pipe

back on the pipe, and secure it with tape.

Fig. 28

Heat insulating

pipe

Pipe

Cut line

Cutter

CAUTION

To prevent breaking of the pipe, avoid sharp bends.

Bend the pipe with a radius of curvature of 150 mm or over.

If the pipe is bent repeatedly at the same place, it will break.

5. 3. Connection pipes

(1) Indoor unit side

Fig. 29

Indoor unit

Large pipe

Small pipe

CAUTION

Be sure to apply the pipe against the port on the indoor unit correctly. If the centering

isimproper,thearenutcannotbetightenedsmoothly.Ifthearenutisforcedtoturn,

the threads will be damaged.

Donotremovethearenutfromtheindoorunitpipeuntilimmediatelybeforeconnect-

ing the connection pipe.

Whenthearenutistightenedproperlybyyourhand,holdthebodysidecouplingwitha

separate spanner, then tighten with a torque wrench (Fig. 30).

Fig. 30

Holding spanner

Body side

90º

Torque wrench

CAUTION

Hold the torque wrench at its grip, keeping it in the right angle with the pipe as shown in

Fig.30,inordertotightenthearenutcorrectly.

9363217094_IM_EN.indd 6 3/15/2018 15:50:47

En-7

Table 4: Flare nut tightening torque

Pipe Tightening torque

Small pipe 30.4 to 34.3 N·m (310 to 350 kgf·cm)

Large pipe 78.4 to 98 N·m (800 to 1000 kgf·cm)

CAUTION

Be sure to connect the large pipe after connecting the small pipe completely.

(2) Outdoor unit side

Tightenthearenutoftheconnectionpipeattheoutdoorunitvalveconnector.The

tightening method is the same as that as at the indoor side.

Fig. 31

Valve A

(small)

Valve B

(large)

Flare nut

Putty

(Large pipe)

(Small pipe)

Connection pipe

5. 4. Vacuum process

1. VACUUM

(1) Vacuum inside the indoor unit and the piping to a pressure of 1.5 mmHg abs or less

from the charging valve with a vacuum pump.

(2) After vacuuming inside the indoor unit and the piping, remove the cap of the two

valves.

(3) Open the handle of the two valves from the closed state (Table 6).

(4) Tightenthecapofthetwovalvestothespeciedtorque.

Table 5

Tightening torque

Large valve Small valve

Handle 1.47 N·m (15 kgf·cm) or less

Cap 14.7 to 19.6 N·m (150 to 200 kgf·cm)

Table 6

Open valve state Closed valve state

* If the handle is not fully open, performance will drop and

an abnormal sound will be generated.

Fig. 32

Valve A

(Small)

Small pipe

Large pipe

cap

Charging

valve

Handle

Service hose

Vacuum

pump

Gauge manifold

Valve B

(Large)

2. ADDITIONAL CHARGE

Refrigerant suitable for a piping length 20 m for other model is charged in the outdoor unit

at the factory.

When the piping is longer than 20 m, additional charging is necessary.

For the additional amount, see the table below.

Table 7

Pipe length

Model type

20 m

(66 ft)

30 m

(99 ft)

40 m

(132 ft)

50 m

(164 ft)

g/m

(oz/ft)

36,000 BTU

45,000 BTU

class

None

400 g

(14.1 oz)

800 g

(28.2 oz)

1200 g

(42.3 oz)

40 g/m

(1.41 oz/3.3 ft)

54,000 BTU

class

None

500 g

(17.6 oz)

1000 g

(35.2 oz)

1500 g

(52.8 oz)

50 g/m

(1.76 oz/3.3 ft)

CAUTION

When charging the refrigerant, always use a measuring cylinder.

Add refrigerant from the charging valve after the completion of the work.

5. 5. Installing the coupler heat insulation

After checking for gas leaks, insulate by wrapping insulation around the two parts (large

and small) of the indoor unit coupling, using the coupler heat insulation.

After installing the coupler heat insulation, wrap both ends with vinyl tape so that there is

no gap.

Fig. 33

CAUTION

Mustttightlyagainstbodywithoutanygap.

Body

Coupler heat

insulation

Be sure to overlap

the insulation

Coupler heat insulation

No gap

9363217094_IM_EN.indd 7 3/15/2018 15:50:48

En-8

6. ELECTRICAL WIRING

CAUTION

Before starting work, check that power is not being supplied to the outdoor unit.

Match the terminal board numbers and connection cord colors with those of the indoor

unit side.

Erroneous wiring may cause burning of the electric parts.

Connecttheconnectioncordsandthepowersupplycordrmlytotheterminalboard.

Imperfectinstallationmaycauseare.

Always fasten the outside covering of the connection cord and the power supply cord

with cord clamps. (If the insulator is chafed, electric leakage may occur.)

Always connect the ground wire.

HOW TO CONNECT WIRING TO THE TERMINALS

For strand wiring

(1) Useringterminalswithinsulatingsleevesasshowninthegurebelowtoconnectto

the terminal block.

(2) Securely clamp the ring terminals to the wires using an appropriate tool so that the

wires do not come loose.

(3) Usethespeciedwires,connectthemsecurely,andfastenthemsothatthereisno

stress placed on the terminals.

(4) Use an appropriate screwdriver to tighten the terminal screws.

Do not use a screwdriver that is too small, otherwise, the screw heads may be

damaged and prevent the screws from being properly tightened.

(5) Do not tighten the terminal screws too much, otherwise, the screws may break.

(6) See the Table 6 for the terminal screw tightening torques.

Fig. 34

Strip 10 mm (13/32")

Ring terminal

Sleeve

Screw with

special washer

Ring terminal

Terminal board

Terminal block

Wire

Screw with

special washer

Ring terminal

Wire

WARNING

Useringterminalsandtightentheterminalscrewstothespeciedtorques,otherwise,

abnormal over-heating may be produced and possibly cause heavy damage inside the

unit.

Table 6

Tightening torque

M4 screw 10 to 16 in.lbs (12 to 18 kgf·cm)

HOW TO FIXED CONNECTION CORD AND POWER SUPPLY CORD

AT THE CORD CLAMP

After passing the connection cord and power supply cord through the insulation tube,

fasten it with the cord clamp.

Fig. 35

Insulation tube

Cord clamp

Use VW-1, 0.5 to 1.0 mm thick, PVC tube as the insulation tube.

1. INDOOR UNIT SIDE

(1) Remove the control box cover and cover (wire) B and install the connection cord.

Fig. 36

Cover (wire) B

Control box cover

(2) After wiring is complete, clamp the remote controller cord and connection cord with the

cord clamp.

(3) Install the control box cover and cover (wire) B.

Fig. 37

Cord clamp

Connection cord

(To the outdoor unit)

Remote controller cord

Fig. 38

Connection

cord

Terminal board

(Indoor unit)

Remote

controller

Black

White

Red

Terminal

board

Outdoor

unit

Ceiling height setting

Set the DIP switch for the ceiling height according to the table below.

Table 7

Ceiling height

(m)

DIP-SW4

1 2 3

2.5 ~ 3.0 Normal — OFF OFF

3.0 ~ 3.5 High ceiling 1 — ON OFF

More than 3.5 High ceiling 2 — OFF ON

Less than 2.5 Low ceiling — ON ON

9363217094_IM_EN.indd 8 3/15/2018 15:50:49

En-9

Fig. 39

SW 4

SW 1

DIP switch

(SW4)

Indoor unit

PC board

Indoor unit PC board

CAUTION

If the setting for a low ceiling is selected, the capacity of the air conditioner decreases

slightly.

Donot setany switchesotherthanthosespeciedin this sheet.Theairconditioner

maynotoperatecorrectlyifanyswitchesotherthanthosespeciedarechanged.

2. OUTDOOR UNIT SIDE

(1) Remove outdoor unit cabinet A and connect the power supply cord and the outdoor

unit connection cord wired at the indoor unit.

(2) Fasten the power supply cord and connection cord with cable clip and binders as

shown in (Fig. 42).

Fig. 40

Electric box

Terminal board

Cord clamp

Power supply cord

Connection cord

(indoor unit and outdoor

unit connection cord)

Ground

Power supply

cord

Fig. 41

(N)

Remote controller

Indoor unit

side terminal

Outdoor unit

side terminal

Power

line

Control line

EARTH

Power supply

Black

White

Red

Fig. 42

Outdoor unit

100 mm (4") or less

Cabinet D

Compressor

Binder

Coupler holder

Cable clip

Power supply cord and connection cord

(indoor unit and outdoor unit

connection cord)

7. GRILLE INSTALLATION

BLOWER COVER INSULATION

Installtheblowercoverinsulationonlywhentheoutletdirectionisnotspecied.

Two blower cover insulations are packed with the indoor unit.

Install the blower cover insulation at the diffuser position shown in Fig. 43. At this time, use

the piping position as the criteria.

Fig. 43

Panel

base

Drain

pan

Blower cover

insulation

(Piping direction)

2 directions example

A-A Section view

INSTALLING THE INTAKE GRILLE

(1) Mount the grille hinge wire to the hook shaft as shown in Fig. 44.

Fig. 44

•Latch the grille hinge wire to the hook shaft, and fasten.

Fig. 45 Part A detail view

Fig. 46 Part A section view

Hook shaft

Grille hinge

wire

9363217094_IM_EN.indd 9 3/15/2018 15:50:50

En-10

(2) Install the hook wire.

•Pass the hook wire through the panel base from the rear side as shown in Fig. 47,

andfastentothereinforcedmetalttingoftheintakegrilleusingascrew.

Fig. 47

RFM (grille)

Hook wire

Fig. 48 Section view

Hook wire

Screw

(3) Loosen the screw, put the loop of the hook wire over it, and tighten the screw again.

CAUTION

Install the intake grille hook wire to the grille assembly. If it falls, it may cause injuries.

(4) Bring up the intake grille by pushing it up at an angle as shown in Figs. 49, 50, and

fasten.

Fig. 49

Fig. 50

8. POWER

WARNING

The rated voltage of this product is 380-415 V 3ø 50 Hz.

Before turning on verify that the voltage is within the 342 to 457 V range.

Always use a special branch circuit and install a special receptacle to supply power to

the air conditioner.

Use a special branch circuit breaker and receptacle matched to the capacity of the air

conditioner. (Install in accordance with standard.)

Perform wiring work in accordance with standards so that the air conditioner can be

operated safely and positively.

Install a leakage special branch circuit breaker in accordance with the related laws

and regulations and electric company standards.

CAUTION

Whenthevoltageislowandtheairconditionerisdifculttostart,contactthepower

company the voltage raised.

9. REMOTE CONTROLLER INSTALLATION

9. 1. Electrical requirement

When connecting the remote controller use the following wiring.

Cable Cable size Remarks

Remote controller cable

22AWG

Sheathed PVC cable,

Polar 3 core

Use Sheathed PVC cable in

accordance with local rules

for cable.

* We recommend that you purchase our service parts for the remote controller cable.

Contact service personnel to purchase this.

9. 2. Dimensions

120

4.5

Hole

15.3

4.5

45.3

63.5

83.5

33.5

4.5

12.5

Hole × 3

Hole × 2

Unit: mm

9363217094_IM_EN.indd 10 3/15/2018 15:50:51

En-11

9. 3. Name of parts

•With cover open

Display panel

•Display panel

13 14 15 16

19 20 21



 “ ”,“ ”(SetTemperatureButton)



 “ ”(TimerMode/ClockAdjustButton)



 “ ”(Day/DayOFFButton)



 “ ”,“ ”(SetTimeButton)



 “ ”(TimerDeleteButton)



 “ ”(TimerSetButton)



 “ ”(Start/StopButton)



 “ ”(ModeButton)



 “ ”(FanControlButton)



 “ ”(HorizontalairowdirectionandswingButton)



 “ ”(VerticalairowdirectionandswingButton)



Operation Lamp



Day Display



Operation Lock Display



Temperature Display



Fan Speed Display



Timer Mode Display



Operation Mode Display



Timer and Clock Display



Vertical Swing Display



Defrost Display

9. 4. Installation

Open the operation panel on the front of the remote controller, remove the 2 screws

indicatedinthefollowinggure,andthenremovethefrontcaseoftheremotecontroller.

When installing the remote controller, remove the connector from the front case.

The wires may break if the connector is not removed and the front case hangs down.

When installing the front case, connect the connector to the front case.

Fig. 51

SET BACK

Front case

(back side)

Rear case

Screws

Connector

When remote controller cable is embedded

(1) Embed the remote controller cable and box.

(2) Pass the remote controller cable through the hole in the rear case and connect the

remotecontrollercabletotheremotecontrollerterminalboardspeciedinFig.52.

(3) Clamp the remote controller cable sheath with the binder as shown in Fig. 52.

(4) Cut off the excess binder.

(5) Install the rear case to the wall, box, etc., with 2 screws (Fig. 53).

(6) Clamp the remote controller cord to a wall, etc. with the remote controller cord clamp

furnished (Fig. 54).

Fig. 52

1. 12V

(Red)

2. Signal

(White)

3. COM

(Black)

7 7 7

Unit : mm

1. 12V

(Red)

Hole

Binder

2. Signal

(White)

3. COM

(Black)

CAUTION

When connecting the remote

controller cables, do not over

tighten the screws.

Fig. 53 [Example]

Remote controller

cable

Connector

Screws

Rear

case

Box

Remote controller

Wrap the connector and remote controller

cables with vinyl tape or some other type

ofinsulationasshowninthegure.

Earth (Ground) the remote controller if it has an earth (a ground) cable.

Fig. 54

Remote controller cord

Remote controller

cord clamp

Tappingscrew(ushheads)

9363217094_IM_EN.indd 11 3/15/2018 15:50:56

En-12

9. 5. Setting the DIP switch

CAUTION

Install the remote controller wires so as not to be direct touched with your hand.

Do not touch the remote controller PC board and PC board parts directly with your

hands.

Set the remote controller DIP switches.

Set DIP switch 1 - NO.6 to ON.

For the other switch, set it according to the situation.

[Example]

Front case (back side)

OFF ON

DIP switch 1

Do not use this

DIP switch 2

NO.

Switch state

Detail

OFF ON

DIP switch 1

Group control setting

Refer to NUMBER OF CONNECTED

UNITS

5 Invalidity

Validity

Auto Restart

Invalidity

Validity

Memory backup setting

* Set to ON to use batteries for the

memory backup. If batteries are not

used, all of the settings stored in

memory will be deleted if there is a

power failure.

NUMBER OF CONNECTED UNITS

Indoor Unit

Address

SW1-1 SW1-2 SW1-3 SW1-4

Single OFF OFF OFF OFF

1 OFF OFF OFF ON

2 OFF OFF ON OFF

3 OFF OFF ON ON

4 OFF ON OFF OFF

5 OFF ON OFF ON

6 OFF ON ON OFF

7 OFF ON ON ON

8 ON OFF OFF OFF

9 ON OFF OFF ON

10 ON OFF ON OFF

11 ON OFF ON ON

12 ON ON OFF OFF

13 ON ON OFF ON

14 ON ON ON OFF

15 ON ON ON ON

(

Factory setting)

9. 6. Connection of Remote Controller Cable

CAUTION

Whenconnectingtheremotecontrollercabletothewallmountedtypeandtheoor

type indoor unit, do not connect it to the outdoor unit or the indoor unit power terminal

block. It may cause a failure.

M4 screw

Terminal block

Black

Indoor unit

side

* Earth (Ground) the remote

controller if it has an earth

(a ground) wire.

White

Red

Remote controller

cable

Remote controller

terminal block

Outdoor unit /

power supply

terminal block

Indoor unit

PCB

It may be failed if it is connected to the outdoor unit or the terminal block for power

supply.

10. SPECIAL INSTALLATION METHODS

10. 1. Group control

•One remote controller can control up to 16 air conditioners.

•All the air conditioners can be operated with the same setting.

WIRING METHOD

(1) Wire each air conditioner (power cord·indoor and outdoor units connection cord)

individually.

For details, refer to the ELECTRICAL WIRING section of the installation instruction

sheet.

(2) Connect the bus wire between the indoor units to [REMOTE CONTROLLER 2, 3] of

the indoor unit terminal board.

(3) Install the remote controller to only one air conditioner and remove the remote

controller of the other air conditioners.

Indoor unit 0

Remote

controller

cord

Bus wire

Remote controller

Indoor unit 1 Indoor unit 2 Indoor unit 15

BUS WIRE

•Use wire having a cross sectional area of 0.75 mm

•Make the total length of the bus wire (including the remote controller cord) 500 m or less.

(4) Fasten the bus wire with a binder

(large) as shown at the right.

Binder (large)

Bus wire

9363217094_IM_EN.indd 12 3/15/2018 15:50:57

En-13

UNIT NO. SETTING METHOD

(Performed at indoor unit)

(1) Remove the electric parts box.

(2) Turn off the main power.

(3) Set the unit number with the rotary switch on the indoor unit PC board so it is not

duplicated. (Unit No. 0-15)

(4) After setting the unit number, restore the electric parts box.

Rotary switch

Indoor unit PC

board

Rotary switch

DIP switch

[SW1]

(Performed by remote controller)

(1) Set remote controller DIP switch 1 [1~4] .

10. 2. Auto restart

SETTING METHOD

(Performed by remote controller)

(1) Turn off the main power.

(2) Set remote controller DIP switch 1 [5] to [ON].

10. 3. Memory backup function

This function starts operation in accordance with the contents before operation was

stopped by pressing of the START/STOP button when the power supply to the air

conditioner was stopped and restarted by a power failure, switch, etc.

•MEMORY BACKUP FUNCTION use in the state in which the remote controller case top

is removed, set DIP switch 1 [6] of the remote controller to the [ON] position.

11. TEST RUN

Check items

(1) Is operation of each button on the remote control unit normal?

(2) Does each lamp light normally?

(3) Doairowdirectionlouversoperatenormally?

(4) Is the drain normal?

(5) Do not have an abnormal noise and vibration during operation?

Do not operate the air conditioner in test run for a long time.

[Operation method]

(1) If the operation lamp is on, press the START/STOP button to turn it off.

(2) Pressthe“

”buttonand“ ”buttonatthesametimeformorethan

2 seconds to start the test operation.

Theoperationlampwilllightupand“

”willbedisplayedonthesettemperature

display.

* Pressing the START/STOP button will stop the test operation.

Test operation display

Run[Self-Diagnosis]if[EE:EE]ashesontheclockdisplayoftheremotecontroller.

SELF-DIAGNOSIS

(1) Stop the air conditioner operation.

(2) Press the Set Temperature buttons

and at the

same time for more than 5 seconds to start the

self-diagnosis.

* For information on the error codes, refer to the

installation manualfor the indoor unit.

(3) Press the Set Temperature buttons

and at the

same time to stop the self-diagnosis.

Example: Self-diagnosis check

Unitnumber(usually“00”)

Error code

Table 8

Error Code Error contents

Communication error

(indoor unit remote controller)

Communication error

(indoor unit outdoor unit)

Room temperature sensor open

Room temperature sensor shortcircuited

Indoor heat exchanger temperature sensor open

Indoor heat exchanger temperature sensor shortcircuited

Outdoor heat exchanger temperature sensor open

Outdoor heat exchanger temperature sensor shortcircuited

Power source connection error

Float switch operated

Outdoor temperature sensor open

Outdoor temperature sensor shortcircuited

Discharge pipe temperature sensor open

Discharge pipe temperature sensor shortcircuited

Outdoor high pressure abnormal

Discharge pipe temperature abnormal

Model abnormal

Indoor fan abnormal

Outdoor signal abnormal

Outdoor EEPROM abnormal

[OUTDOOR UNIT]

When the outdoor temperature drops, the outdoor unit’s fans may switch to low speed.

ERROR : HEAT & COOL MODEL (REVERSE CYCLE) ONLY

The LED lamps operate as follows (Table 9) according to the error contents.

Table 9

Error display

Error contents

LED1 LED2

0.1 sec.

OFF

0.1 sec.

OFF

Model abnormal or

EEPROM abnormal

Quickashcontinued Quickashcontinued

0.5 sec.

2 sec.

OFF

Power source

connection error

1quickashrepeated Lighting continued

0.5 sec.

2 sec.

OFF

Discharge temperature

sensor error

2quickashrepeated Lighting continued

0.5 sec.

2 sec.

OFF

Outdoor heat exchanger

temperature sensor error

3quickashrepeated Lighting continued

4quickashrepeated Lighting continued

Outdoor temperature

sensor error

5quickashrepeated Lighting continued Communication signal error

6quickashrepeated Lighting continued Indoor unit error

7quickashrepeated Lighting continued

Discharge temperature

abnormal

8quickashrepeated Lighting continued High pressure abnormal

When the fault is cleared, the LED lamp goes off.

However, for discharge pipe temperature abnormal and high pressure abnormal, the LED

lamp lights continuously for 24 hours, as long as the power is not turned off.

9363217094_IM_EN.indd 13 3/15/2018 15:51:01

En-14

[CHECKING DRAINAGE]

Tocheckthedrain,removethewatercoverandllwith2to3Rof water as shown in

Fig. 55.

The drain pump operates when operating in the cooling mode.

Fig. 55

Drain pipe

Watering pot

Water cover

12. OPENING THE DUCT CONNECTION HOLE

Fig. 56

Distribution duct Fresh air

Distribution duct

CAUTION

When performing hole opening work, be careful not to damage the drain pan.

Whenconnectingthedistributionduct,tomaketheairoweasily,blocktheoutlet

port with the blower cover insulation as shown by the hatched lines in Fig. 56. For the

blocking direction, refer to Fig. 43.

1. DIMENSION

Screw position and connection hole which are fresh air duct and distribution duct.

Fig. 57

P. D 120 P. D 88

12-ø3.3 self tapping screw holes (for 4 mm)

ø70

ø100

45°

160 334.2

113

45°

Unit: mm

2. DISTRIBUTION DUCT AND FRESH AIR DUCT HOLE PROCESSING

Use the distribution duct hole and fresh air duct hole by removing the insulation material as

shown below.

Fig. 58

Cut

Cabinet

•Cut off the part (Cabinet) indicated by the arrow in the Fig. 58 with nippers, needle nose

pliers, etc.

Fig. 59

Knife

Insulation

(Inner box)

Cabinet

•Open the holes and cut the insulation with a knife.

* Be careful not to damage the internal parts.

* Be careful not to cut yourself on the cutout in the metal plate.

* Please remove the insulation (inner box) left over after cutting.

•Connect the distribution duct.

* When mounting the duct, block the gap so that there is no cold air leakage.

* Insulate the duct and cut connection.

CAUTION

The air conditioner cannot take in fresh air by itself. When connecting a fresh air duct,

always use a duct fan.

13. CUSTOMER GUIDANCE

Explain the following to the customer in accordance with the operating manual:

(1) Starting and stopping method, operation switching, temperature adjustment, timer, air

owswitching,andotherremotecontrollerunitoperations.

(2) Cleaningandmaintenanceoftheproduct,andotheritemssuchasairltersandair

louvers if applicable.

(3) Give the operating and installation manuals to the customer.

(4) If the signal code is changed, explain to the customer how it changed (the system

returns to signal code A when the batteries in the remote controller unit are replaced).

*(4) is applicable to using wireless remote controller.

9363217094_IM_EN.indd 14 3/15/2018 15:51:02

9363217094_IM_EN.indd 15 3/15/2018 15:51:02

Fujitsu AUG45ALB3W Installation guide

Brand: Fujitsu

Model: AUG45ALB3W

Category: Split-system air conditioners

Type: Installation guide

This manual is also suitable for

Download PDF

report

Fujitsu AUG45ALB3W Installation guide

This manual is also suitable for

Fujitsu AUG45ALB3W Installation guide

Related papers

Other documents