Page is loading ...
ML- 55CX-MTS-123A-5
Customer Notice
Please kindly read the entire instructions
before you start assembling.
* If is there is anything wrong with our product, please
kindly contact us at: maxlead.us@gmail.com without
any hesitation before you use it. Each email will be
replied in 24hrs except WEEKEND & HOLIDAY.
FOR YOUR SAFETY
CUSTOMER SERVICE
TV Size: Suitable for 32-65"
* Please do not exceed 110lbs and size of TV should be
within 32"-65". Or might the stand will lean foward then
TV fall off to ground which might cause serious injury
or property damage .
* Please kindly keep children away from the stand as it
is made of steel and very heavy.
* Please follow the entire instructions to assemble the
item. Improper installation may cause potential safety
hazard.
* Please tighten the screws firmly when assembling, but
Please do not over tighten. As it might cause damage
to the item which may greatly reduce its holding ability.
* Please always put this stand on level surface.
!
?
WARRANTY INFORMATION
* "Defective on Arrival" claims should be made within 30
days after you receiving the Item. So please kindly check
the condition ASAP after you receive the item.
* We provide 1 Year warranty for replacing parts if needed.
Please kindly contact us via email provided, and we will
spare no effort to help you solve the problems you met.
h
a
H Base
g Nut
I
J
D
Brake Casters
Make sure caste rs'
screws are tigh t by
using the wrenc h to
contrarot ate the nut
h
b
Spring
Plunger
Anticlockwise rotate the Casters into the foot.
Washer
Fix the screw
by allen wrench
when tighten
the g Nut
Install the legs into the base. Tighten the nuts by wrench
2 Inch’s
increment
Decide the height needed,
then install the part#F poles
into part#G welded poles.
Spring plunger is for locking.
Swivel the poles in.
c
h
Fix the welded poles into
base by allen wrench.
Front Leg
Rear Leg
Caster
Poles with
holes sides,
face to
rear legs.
e
K Shelf Brackets
Decide the height needed, then fix the brackets to poles.
Then install the shelf onto the brackets.
Or you can firstly fix the shelf to brackets and then install
the assembled set to poles.
a
b
c
d
e
f
g
h
i
j
M8 Allen Wrench
Wrench
M6 Knob
6*13mm Plastic Space
8*14mm Plastic Space
6mm Washer
8mm Washer
M8 Nut
M6*8mm Screw
6mm Washer
M6 Nut
M6*12mm Screw
M8*25mm Screw
M6*25mm Screw
M8*25mm Hexagon Screw
M8*20mm Hexagon Screw
M8*65mm Hexagon Screw
M5*25mm Screw
12
2
2
4
4
4
2
4
4
4
12
24
4
4
4
2
2
1
a b c d
e
f
g
i
h
j
FOUR
a
h
g
Install the TV mount.
Fix the screw
by allen wrench
when tighten
the g Nut.
Use wrench to
tighten the g nuts.
f
Install the camera shelf
to support bar by using
part#f sets with small
wrench.
Decide the height needed,
then install the assembled
set to TV mount.
6
7
8
M6 knob
Washer
Screw
Assemble part#B.
3 different type of screws(part#d) are
provided for assembling arms to TV.
Part#i(6mm washer) for m5 or m6 screw.
Part#h(8mm washer) for m8 screw.
Please kindly use the appropriate ones
which are suitable for your TV.
Assemble the arms to
back of screen.
NOTE: Arms with hook side
should be installed at top
of the screen back.
FIVE
Hook the assembled
screen to TV mount.
Plastic spaces(part#j) are provided
to secure arms to screen panel
if needed. Please kindly choose
appropriated ones.
TOO LOOSE
FIT PROPERLY
Please kindly ask
someone to help you.
!
Tighten all screws but
do not OVER tighten.
h
Tighten the screws(which are already
screwed on the arms by screwdriver to
secure the assembled arms to back
of TV Mount.
Then the installation finished.
Use the provided velcro to
manage cables if needed..
Please kindly check if the
arms are safely secured on
the TV Mount at regular
intervals(at least every
twomonths).
Please online search at http://bit.ly/2ei8cLB
to get videos for installation.
TV must NOT
exceed 110lbs!
!
Left and right arms.
/
