SharkBite 24438A Specification

2

Table of Contents

SYSTEM DATA SHEET ................................................................................................................................... 3

ENGINEERING SPECIFICATIONS .................................................................................................................... 4

THE SHARKBITE DESIGN (1/4” – 1”) .............................................................................................................. 7

WHY SHARKBITE? ........................................................................................................................................ 7

CONNECTING A SHARKBITE FITTING ............................................................................................................. 8

DISCONNECTING A FITTING.......................................................................................................................... 9

SHARKBITE SLIP PRODUCTS ....................................................................................................................... 10

SHARKBITE SLIP PRODUCTS ....................................................................................................................... 11

SHARKBITE FOR CONCEALED AREAS ........................................................................................................... 11

DIMENSIONS ............................................................................................................................................. 12

PRESSURE LOSS AND FLOW RATES ............................................................................................................. 13

THE SHARKBITE 2XL DESIGN (1-1/4” – 2”) .................................................................................................. 16

WHY SHARKBITE 2XL? ................................................................................................................................ 17

HOW TO MAKE A SHARKBITE 2XL CONNECTION ......................................................................................... 18

DISCONNECTING A SHARKBITE 2XL CONNECTION ...................................................................................... 19

SHARKBITE 2XL DIMENSIONS ..................................................................................................................... 20

SHARKBITE 2XL PRESSURE LOSS AND FLOW RATES ..................................................................................... 21

SHARKBITE PEX TUBING ............................................................................................................................. 24

PEX PIPE SPECS AND DIMENSIONS ............................................................................................................. 25

IAPMO RESEARCH AND TESTING, INC. ........................................................................................................ 27

WARRANTY ............................................................................................................................................... 32

3

SYSTEM DATA SHEET

System Description

The SharkBite Push-Fit quick-connect

plumbing system is the easiest and most

dependable way to join copper, CPVC or

PEX pipe in any combination—with no

soldering, clamps, unions or glue.

Available in an assortment of over 200

fittings and sizes ranging from ¼” to 2”

copper tube size (CTS).

Applications

Tubing: Hard drawn copper pipe Type K,

L and M and annealed Type M not to

exceed 3/8 nominal complying with

ASTM B 88, PEX tubing complying with

ASTM F 876 or CSA B137.5, or CVPC

tubing complying with ASTM D 2846 or

CSA B137.6. SharkBite fittings are

approved for installations above and

below ground applications. Please

consult with local code for final approval.

Failure to comply with the above types

of pipe or application could result in

connection failures.

Operating Parameters

Operating Pressure: 200 PSI Max

Operating Temperature: 200°F Max

Approved Applications

 Potable Water

 Hydronic Heating (w/ Glycol

concentration up to 100%)

System Benefits

 Instant push-fit connection for

increased ease of use

 No soldering, clamps, unions or

glue needed

 Reduces installation time with no

tightening of nuts, clamps and

unions.

 Connects three types of pipe in any

combination

 No mapping of system

 Can be installed wet or dry

 Rotatable after installation

 Approved for behind the wall and

underground applications.

 Removable after installation

 Clean, professional installation

Fittings

SharkBite push-fit fittings are available in

200+ configurations including: Couplings,

Elbows, Tees, Reducers, Threaded

Adapters, Caps, Stops, Stub Outs, Ball

Valves, Slips, Water Heater Hoses and

Valves with SharkBite Connections.

Made from Lead Free Dezincification

Resistant (DZR) brass and available in

sizes ¼” – 2” CTS.

Push-Fit Technology

The SharkBite fitting works via a two

stage process that ensures a quick, easy

connection.

 The tubing passes through the

release collar and then through the

stainless steel grab ring.

 The tube is pushed through an

o-ring protector that aligns the tube.

It then passes through a specially

formulated o-ring that compresses

between the pipe and the wall of

the fitting before it reaches the tube

stop.

How to Make a Connection

1. Cut the pipe. Make sure the cut is

square and even.

2. Deburr the end of the pipe to

remove any sharp edges. Sharp

edges can cut the o-ring and lead

to leaks.

3. Mark the pipe with the proper

insertion depth (see below for

reference).

4. Push the pipe into the fitting. The

mark made on the pipe should

rest against the collar of the

fitting, ensuring a proper seal.

FITTING SIZE

INSERTION DEPTH

1/4”

0.813”

3/8”

0.875”

1/2”

0.938”

5/8”

1.125”

3/4”

1.125”

1”

1.313”

1-1/4”

2.000”

1-1/2”

2.250”

2”

2.500”

Tube Liner

SharkBite fittings ranging in sizes 3/8” to

1” come with an integral tube liner

preinstalled for use with PEX pipe.

SharkBite sizes 1-1/4” to 2” do not come

with tube liners preinstalled and are sold

separately. The tube liner must be used

when PEX piping is utilized.

Tools

Tools are available to make the

installation process easier.

 SharkBite depth & deburring tool for

1/4” to 1” CTS

 SharkBite depth & deburring tool for

1-1/4” to 2” CTS

 SharkBite disconnect clip (1 size per

tubing)

 SharkBite disconnect tongs (1 size

per tubing)

History

SharkBite was launched in the Australian

market in 1999 and in the North America

market in 2004, ushering in a new way to

do plumbing. Reliance Worldwide, an

ISO 9001 organization, is one of the

world’s largest manufacturers of

thermostatic water control valves and

has been a major world supplier of hot

water safety valves for over 50 years.

Warranty

SharkBite fittings carry a 25 year

warranty against any manufacturer’s

defect as long as the item has been

installed per installation instructions and

comply with local code. Please contact

Customer Service for more information.

IAPMO

http://pld.iapmo.org/default.asp

(Select Listee Name and enter

“Reliance Worldwide”)

For more information on SharkBite

products, contact:

Reliance Worldwide Corporation

2727 Paces Ferry Road

Building 2, Suite 1800

Atlanta, GA 30339

United States: 1-877-700-4242

Canada: 1-888-820-0120

Web: www.sharkbite.com

4

ENGINEERING SPECIFICATIONS

The push-fit fitting shall be installed on hard drawn copper type K, L and M complying with ASTM B88, cross-linked

polyethylene pipe (PEX) complying with ASTM F 876 or CSA B137.5 or CPVC piping complying with ASTM D 2846 or CSA

B137.6. The fitting shall be made of lead free dezincification brass and compliant with ASSE 1061, NSF/ANSI 61 and

NSF/ANSI 372. The fitting shall consist of an EPDM O-ring, a grade 316 stainless steel grab ring, and contain a polysulfone

tube liner for PEX applications. The fitting shall be used in a potable water system or a hydronic heating water

distribution up to 200 psi and 200°F. The fitting shall be a SharkBite fitting.

PART 1: GENERAL

1.1 SUMMARY

A. Push-Fit Connection System for Potable Water Distribution and Hydronic Heating Water Distribution

1.2 DEFINITIONS

A. ASME: American Society of Mechanical Engineers

B. ASSE: American Society of Safety Engineers

C. ASTM: American Society for Testing and Materials

D. CSA: Canadian Standards Association

E. EPDM: Ethylene Propylene Diene Monomer

F. IAPMO: International Association of Plumbing and Mechanical Officials

G. NSF: National Sanitation Foundation

1.3 REFERENCES

A. ASSE 1061: Performance Requirements for Push-Fit Fittings

B. NSF/ANSI Standard 61: Certification for Drinking Water System Components – Health Effects

C. NSF/ANSI Standard 14: Plastics Piping System Components and Related Materials

D. NSF/ANSI Standard 372: Lead Content Certification

E. ASTM B 88: Standard Specifications for Seamless Copper Water Tube

F. ASTM F 876: Standard Specification for Cross-linked Polyethylene (PEX) Tubing

G. CSA B137.5: Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications

H. CSA B137.6

I. ASTM D 2846: Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot-and Cold-Water

Distribution Systems.

J. IAPMO: Uniform Plumbing Code

K. IAPMO: National Plumbing Code of Canada

L. IAPMO: International Plumbing Code

M. AWWA C904: Cross-Linked Polyethylene (PEX) Pressure Pipe, ½ In. (12mm) Through 3 In. (.76 mm) for Water

Service.

1.4 QUALITY ASSURANCE

A. Installer shall be well informed on installation instructions prior to installing.

B. The installation of tubing and fittings for hot and cold water distribution systems shall conform to the

requirements of the ICC International Plumbing Code or IAPMO Uniform Plumbing Code.

C. The piping shall be cut square, even and have no rough edges.

5

1.5 WARRANTY

A. SharkBite Push-Fit Fittings have a 25 year limited warranty from point of sale.

B. All products must be installed in accordance with all applicable codes and in accordance with any local,

state, provincial or federal requirements.

C. The installing contractor must use construction techniques compliant with applicable codes to install the

range of products and use the product(s) within the design parameters specified in any installation

guidelines and technical notes for the applicable system. This shall include field pressure testing prior to

concealing with concrete or by other means.

D. Products must not be installed in a system that may operate at temperatures or at pressures that exceed

the printed rating on the product, packaging or installation instructions.

E. Evidence of tampering, mishandling, neglect, accidental damage, freeze damage or unauthorized

modifications or repairs that cause damage to RWC warranted products void any warranty coverage of

those particular products. It is expressly understood that failure as a result of any freezing fluids within the

pipes does not constitute a defect in material or workmanship and shall not be covered by this warranty.

F. Although RWC provides a plumbing system to facilitate a complete installation, other manufacturers tubing

and/or fittings may be installed in any given installation provided manufacturing of the tubing and/or fittings

demonstrates compliance with the applicable ASTM standards, and the product has been certified by a

recognized third-party testing agency. The RWC product in the given installation will continue to be covered

under this warranty. NOTE: RWC will be responsible only for proven defects in material or workmanship in

RWC products. Problems in products manufactured by another company should be reported to that

manufacturer.

G. For full warranty information, please see page 30.

PART 2: PRODUCTS

2.1 MANUFACTURERS

A. RWC, 2727 Paces Ferry Road, Building 2, Suite 1800, Atlanta, GA 30339

Telephone: 1-877-700-4242, Website: www.sharkbite.com

2.2 MATERIAL

A. Tubing Standard: Copper tubing shall be hard drawn Type K, L, or M and annealed Type M copper complying

with ASTM B 88.

B. Tubing Standard: Cross-linked polyethylene pipe (PEX) shall conform to ASTM F 876 or CSA

B137.5.

C. Tubing Standard: CPVC tubing shall conform to ASTM D 2846 or CSA B137.6.

D. O-ring shall be made from EPDM.

E. Grab ring shall be made from Grade 316 Stainless Steel.

F. Push-fitting: Brass fitting shall comply with ASSE 1061 and NSF/ANSI 61.

2.3 SOURCE QUALITY

A. All fittings in contact with drinking water shall be listed by a third party agency to NSF 61.

6

PART 3: EXECUTION

3.1 EXAMINATION

A. If installing PEX pipe, ensure that the tube liner has been installed.

B. Ensure the fitting is free from any damage, including but not limited to damaged or missing O-ring, cracked

brass forging or deformed grab ring.

3.2 PREPARATION

A. The tubing shall be cut square to ensure a proper connection.

B. The tubing shall be free of dirt, debris or scale buildup. Any burrs shall be removed using a deburring tool.

C. Mark the piping to use as verification of proper insertion into the fitting.

3.3 INSTALLATION

A. Push-fit fitting shall be installed in accordance with the manufacturer’s installation instructions.

B. Pressure Rating: Install components having a pressure rating equal to or less than the system operating

pressure.

C. Threaded Joints: Threaded joints shall have thread seal tape applied to the male threads only. Tighten joint

with a wrench and backup wrench as required.

D. Pipe Protection: Provide protection against abrasion where tubing/fitting is in contact with other building

materials (including burial) by wrapping with an approved tape, pipe insulation or otherwise suitable

method of isolation.

E. Hydronic Heating: Glycol mixture for hydronic heating application is acceptable up to and including 100%.

F. Behind the wall installation: Pressure test system for no less than 24 hours to ensure no leakage.

G. Removal and reuse of push-fit fitting is allowed when executed in accordance with manufacturer’s

installation instructions.

3.4 FIELD QUALITY CONTROL

A. Water Testing: The copper tubing system shall be water tested for joint tightness. The piping system shall be

filled with water. The system shall be pressurized to the maximum pressure and length of time required by

the code or standard. The system shall have no leaks at the rated pressure.

7

THE SHARKBITE DESIGN (1/4” – 1”)

The SharkBite Fitting incorporates a number of unique and patented features.

WHY SHARKBITE?

 Instant push-fit connection for increased ease-of-use:

o No soldering, clamps, unions, or glue required.

 Fittings certified to 200 PSI and 200°F (93°C):

o Proven durability and quality.

 Fits copper tubing, and CTS CPVC and PEX:

o Connects all three types in any combination.

 Integral tube liner for PEX installations:

o Integrated design means no loose components, ensures secure, reliable connection.

 Design certified and agency listed:

o Inspector friendly, peace of mind!

 Compact, robust DZR brass body:

o Foundation of a strong, corrosion resistant, durable fitting.

 Design certified to ANSI/NSF-61 and ASSE 1061 product standard for use in potable water and

hydronic heating water distribution:

o Quality engineered and manufactured.

 Approved to be used underground and behind walls without access panels.

o Designed for hydronic heating as well as potable water distribution.

8

CONNECTING A SHARKBITE FITTING

1. Cut the desired length of pipe.

 Make sure cuts are square and even.

2. Deburr the end of the pipe to remove any

sharp edges.

 This will ensure that the o-ring will not

be damaged upon insertion of the pipe.

3. Using a depth gauge, mark the pipe.

 A 1” mark on the pipe can be used as a

guideline. Proper insertion depths are

listed below.

 This will let you know if your

connection is successful.

Pipe Size

Insertion Depth

1/4”

0.813”

3/8”

0.875”

1/2”

0.938”

5/8”

1.125”

3/4”

1.125”

1”

1.313”

4. Push the pipe into the fitting.

 The mark you made on the pipe should

rest against the edge of the fitting.

9

DISCONNECTING A FITTING

With the Disconnect Clip

1. Place the SharkBite disconnect clip around

the tube with the non-branded side against

the release collar.

2. Push the clip against the release collar and

pull the tube with a twisting action to release

the tube.

With Disconnect Tongs

1. Place the teeth around the fitting assembly.

The fork end with the SharkBite brand logo

should be positioned around the tube and the

other end around the neck of the fitting.

2. Squeeze the tool with one hand and pull the

tube with a twisting action with the other

hand to release the tube.

Check the fitting and tube end for damage. The

fitting and tubing should be free of damage,

foreign objects and marks on the outside

diameter. If the tubing is damaged or marked,

then cut and use a new section of tubing.

10

SHARKBITE SLIP PRODUCTS

Slip fittings simplify repair by doing the job that two couplings and extra pipe would do. Only one end of the coupling has

a stop, allowing the other end to slide freely over the end of a pipe. The fitting can be released with a disconnect tool

and slid back onto the other end of the pipe for successful leak repair.

Cut out the section of the pipe needing repair (no more

than 2” in length).

Using the SharkBite Deburring & Depth Gauge, clean the

edges of the copper pipe. Use the gauge to mark the

proper insertion depth on the pipe.

On the side of the fitting marked “SLIP END,” slide the

copper pipe into the fitting until it bottoms out.

Place the SharkBite Disconnect Clip on the copper pipe,

on the same side as the “SLIP END.” As you are pressing

the clip to release the fitting, slide the SharkBite fitting to

meet the other copper pipe.

Continue to slide the fitting until the non-slip end bottoms

out. Ensure the fitting lines up with the mark you made.

Also ensure the Slip End of the fitting has not proceeded

past the depth mark you originally made.

11

SHARKBITE SLIP PRODUCTS

In addition to slip coupling and tees, we also have slip ball valves and slip pressure regulators available to ease

installation woes.

To see an installation video on installing a slip fitting, please visit:

http://www.youtube.com/watch?v=lgdBv5BK5dQ&list=PL0ABAD0AF076CFA60&feature=c4-overview-vl

SHARKBITE FOR CONCEALED AREAS

SharkBite fittings can be utilized in underground applications and as manufactured joints without access

panels, per IAPMO Certificate of Listing File No. 4630.

If burying SharkBite, it is recommended:

Fitting should be wrapped with an impervious material, chloride-free tape or tightly wrapped and sealed

insulation works well to prevent direct contact with the backfill. Backfill should be free of rocks, debris or any

sharp objects that may cause damage through impact or abrasion.

It is also recommended to pressure test the system for 24 hours before closing up any inaccessible location.

12

DIMENSIONS

13

PRESSURE LOSS AND FLOW RATES

14

15

16

THE SHARKBITE 2XL DESIGN (1-1/4” – 2”)

316 Stainless Steel

Grab Ring

Lead Free DZR Body

Nylon Disconnecting

Ring

EPDM O Ring

PPSU Locking Ring

SharkBite

Logo

17

WHY SHARKBITE 2XL?

 Quick Connect:

o No tools, soldering, clamps, unions or glue required. Cut pipe square, de-burr to remove rough

edges/debris, mark the pipe for correct depth and push to get a pressure ready connection every time.

 Quick Disconnect:

o Disconnect in seconds by sliding the De-Mount Tool down the pipe to engage the demount lugs and

rotate clockwise to lock the open position leaving both hands free, you can now remove the pipe.

 SAFE-Recessed Release Collar:

o Commercial SharkBite require a special Demount Tool and cannot be accidentally

disconnected/released.

 Extensive Range Including Slip Feature on Couplings and Tee’s:

o When repairing or tapping into existing pipe with “Push-Fittings” you must be able to either move the

fitting or the pipe to ensure the pipe is engaged fully into the fitting. With rigid pipe like copper the only

way with “Push-Fittings” is to have a SLIP feature to allow easy installation when tapping into existing

pipe.

 Easy Installation:

o Unlike the tool intensive connection methods there is NO need to send multiple fitters to a job,

SharkBite 2XL has been designed to be installed or removed by one person. All fittings are lubricated for

easy connection and by fitting the De-Mount Tool before engaging the pipe the force required can be

reduced further. With the De-Mount Tool locked on you also have hands free disconnection. WET OR

DRY: No waiting for copper tube to dry before soldering or glue to cure, SharkBite makes an instant

connection in seconds.

 No Tools:

o Unlike alterative tool intensive connections systems, SharkBite has no special tooling required for

installation.

 No Time:

o Fastest connection - CUT-PUSH-DONE.

o Easy access to small or tight places.

o No Flame - Does not require fire permit or fire marshal.

 No Waste:

o Should you make an error or simply want to change your installation, no problem for SharkBite. Simply

remove and re-use. (Fittings used for repeated testing must not be used in any permanent application).

 Fittings Cannot be Disassembled:

o SharkBite 2XL Fittings are factory assembled and components cannot be removed.

 Long Pipe Engagement:

o Provides pipe support against lateral pipe forces.

 Lead Free (LF) Dezincifcation Resistance (DZR) Brass:

o Exceeds current no lead legislation - AB1953 or NSF372. Suitable for underground installation subject to

local code authorites/inspectors. Dezincification properties (DZR) exceed ISO6509 and NSF-14.

 Environmentally Friendly:

o Remove and re-use fittings, no need to be scrapped. No heat is required for installation.

18

HOW TO MAKE A SHARKBITE 2XL CONNECTION

1. Cut copper, CPVC or PEX using a quality tuber or

pipe cutter with a sharp blade.

2. Remove burrs and ensure pipe surface is free of

scratches and any debris. It is critical that pipe be

marked with the correct insertion depth as listed

below:

1-1/4" Pipe Insertion Depth = 2"

1-1/2" Pipe Insertion Depth = 2-1/4"

2" Pipe Insertion Depth = 2-1/2"

3. Align pipe with the fitting, insert pipe while

rotating either pipe or fitting.

4. SharkBite 2XL PEX Stiffener must be inserted into

PEX pipe prior to fitting.

Connection is complete when pipe is fully inserted

with depth insertion marked on pipe is still visible

at the head of the fitting

19

DISCONNECTING A SHARKBITE 2XL CONNECTION

1. Place the Shark Shifter De-Mount Tool on the pipe

just above the connection. Then slide the tool

down to engage lugs on the head of the fitting.

2. Rotate the Shark Shifter De-Mount Tool clockwise

to lock onto the lugs. This will lock the Shark

Shifter De-Mount Tool in place.

3. Rotate the Shark Shifter De-Mount Tool clockwise

to lock onto the lugs. This will lock the Shark

Shifter De-Mount Tool in place.

With the Shark Shifter De-Mount Tool Withdraw

locked in place, pull the pipe from the fitting.

Rotate the Shark Shifter De-Mount Tool counter-

clockwise to remove the fitting.

20

SHARKBITE 2XL DIMENSIONS

Page is loading ...

SharkBite 24438A Specification

SharkBite 24438A Specification

Related papers

Other documents