Monte Carlo DRM24AGP Installation guide

Type
Installation guide
DOWNROD REPLACEMENT FOR 3MNLR56/72XXD SERIES FAN
READ AND SAVE THESE INSTRUCTIONS
Warning: Make sure main power is turned off before handling parts
replacement.
Installation work and electrical wiring must be done by qualified person(s). If you
are unfamiliar with methods of installing or electrical wiring, secure the service of a
qualified electrician.
All electrical connections must be in accordance with local codes, ordinances, and
national electrical codes.
Review the installation instructions supplied with your fan. Make sure that your fan
has been wired properly into the ceiling.
Warning: Cross pin and keeper pin must be installed securely with yoke and
downrod, and the pin in hanger ball must be installed in slot of hanger ball and
through downrod, failure to install them will result in serious injury.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver,
Pliers, Safety Glasses, Stepladder and Wire Strippers
2
© 2013 Monte Carlo Fan Company
12/20/2013
ON
OFF
ON
OFF
Before you begin handling parts
replacement, Switch power o at Service
panel and lock service disconnecting
means to prevent power from being
switched on accidentally. When the
service disconnecting means cannot be
locked, securely fasten a warning device,
such as a tag, to the service panel.
Remove hanger ball from existing
downrod by loosening the set screw on
hanger ball until the ball can be moved
freely. Remove the pin and hanger ball
from downrod. Keep the parts.
Place fan assembly on styrofoam to keep
the LED light kit away from damage and
make fan installation easier.
Flip the bottom styrofoam over, aligning
the part of the LED light kit with the hole
in the styrofoam and then place the fan
assembly on it for downrod installation.
Thread lead wires provided through the
long downrod and then Thread the safety
cable provided through downrod (the end
with loop installed downward) and
connect it to the safety cable from fan
(Parts are in the column).
Slide cable clamp onto the safety cable
from fan. Place the end of cable through
the loop of ceiling support cable and then
feed end of cable into clamp hole and
rmly tighten set screw. Cut o excess
safety cable and then pull the safety cable
up from top of downrod.
Note: Make sure to pull the safety cable up before you go next step of lead wires connection.
Connect lead wires (the plugs from fan to the plugs from downrod side) and than install the downrod as fan installation instruction
manual.
Helpful hint: To pull the lead wires from top side of downrod will help for downrod installation. Use a thin iron wire may help to pull the
lead wires through long downrod. Tie the lead wires with an iron wire, thread the iron wire through downrod rstly and then pull the
iron wire with the lead wires through downrod. Make sure the plugs connections won’t be pulled out.
Reinstall the hanger ball onto the downrod. Slip the hanger ball over downrod and then Insert the pin into the holes on downrod.
Align the grove in hanger ball with the pin and pull the hanger ball up tight against the pin. Tighten securely the set screw on the
hanger ball.
Warning: Pin must be installed in slot of hanger ball and through downrod, failure to install them will result in serious injury.
Place column over downrod and put it in position by aligning the recessions with the set screws on top side of housing as fan
installation instruction manual.
Note: Refer to fan installation instruction manual to nish fan installation.
Pin
Setscrew
Keeper pin
Cross pin
Fan wires
Hanger
Ball
Light wires
Column
Canopy
ring
Keeper pin
Cross pin
Yoke
Canopy
Column cover
Downrod
Column
Column
Cover
Set screw
Refer to fan installation instruction manual
Ball Assembly
Fan Wiring
Downrod
Support
Attach Safety
Cable to Ceiling
Support Cable
Light wires
Fan wires
Cable clamp
Set screw
Safety cable
Long
Downrod
Pin
Setscrew
Light wires
Fan wires
Safety cable
LED light kit
1 2 3
4
Dec.2013
Apr.2015 update, use thin iron wire...
  • Page 1 1
  • Page 2 2
  • Page 3 3

Monte Carlo DRM24AGP Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI