Symmons S-6612-STN-1.0 Installation guide

Unity

®

Model Numbers

Single Handle Centerset Lavatory Faucet

Operation & Maintenance Manual

S-6610-1.5, S-6612-1.5

Single handle centerset lavatory faucet featuring a

4" mounting conguration. Includes ceramic cartridge,

1/4" copper supply lines, 1/2" IPS inlet connections,

50/50 drain assembly and standard 1.5 gpm (5.7 L/min)

aerator. Components made from brass and nonmetallic

materials plated in standard polished chrome nish.

Speciﬁcation

Dimensions

Note: Dimensions subject to change without notice.



-0.5 0.5 gpm (1.9 L/min) aerator



-1.0 1.0 gpm (3.8 L/min) aerator



-G Grid drain



-Delete

Sufﬁx

1.5

2.2 gpm (8.3 L/min) aerator



-MP Metal pop-up drain in place of standard



-STN Satin Nickel ﬁnish

Modiﬁcations

Note: Append appropriate -sufx to model number.

CG



S-6610-1.5

Unity Single Handle Centerset Lavatory Faucet

Less Rod



S-6612-1.5

Unity Single Handle Centerset Lavatory Faucet

Measurements

A 6-5/8", 168 mm

B 3-3/8", 86 mm

C 5-7/8", 149 mm

D 4-1/2", 114 mm

E

Deck Thickness Ref.

Max. 1-3/8", 35 mm

F

Hole Size

Ø 1-3/8", 35 mm

G

(2x) Hole Size

Ø 1-1/2", 38 mm

H 3-1/4", 83 mm

I 5-3/4", 146 mm

J Min. 2-1/2", 64 mm

K 1/2-14 NPSM

BB

CC

EE

HH

II

JJ

GG

AA

FF

DD

KK

Compliance

Certied by

CSA Group

-NSF/ANSI 372, NSF/ANSI 61.9

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

WARNING: This product can expose you to chemicals

including lead, which is known to the state of California to

cause cancer, birth defects, or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

2

*Note: Append -STN to part number for Satin Nickel

nish.

Replacement Parts

Item Description Part Number

A

B

C

Handle Kit RL-212*

E Lift Rod RL-213*

G Cartridge KN-4-EXT

K

L

N

Mounting Hardware RL-214

I Aerator

RL-215-2.2* (2.2)

RL-215-1.5* (1.5)

RL-215-1.0* (1.0)

RL-215-0.5* (0.5)

I

Non-Aerated Laminar

Flow Restrictor

RL-215-NA-0.5* (0.5)

M

50/50 Drain Assembly

Metal Drain Assembly

RL-223*

(S-6612-1.5)

O Grid Drain Assembly

P-26*

(S-6610-1.5)

P Metal Drain Assembly

RL-154LR*

(S-6610-1.5)

Tools Required

Adjustable wrench

Allen wrench (3/32”)

Plumber putty

Plumber tape

A

H

C

K

M1

M2

M3

M8

M14

M4

M5

M6

M7

M9

M10

M13

M11

M12

D

E

F

G

I

B

J

L

N

M

O

P

Parts Breakdown

3

J

H

N

2) Place brackets (K) onto threaded

rods (J) and secure with nuts (L).

1

2

J

K

L

If replacing an older faucet

ensure water supply is turned

OFF before removing, then

turn faucet control valve ON to

relieve water pressure.

1) Insert faucet body (H) and

threaded rods (J) through mount-

ing gasket (N) and sink holes.

3) Seat ange (M2) into sink (M3

gasket optional). Install gasket

(M4), washer (M5) and nut (M6)

onto ange (M2) from below sink,

but do not secure nut. Screw on

tail piece (M7) and hand tighten.

2

3

M2

M7

PLUMBER

PUTTY

OPTIONAL

M3

M4

M5

M6

4) Turn tail piece (M7) and ange

(M2) so pivot is facing toward

faucet. Pull assembly down into

drain hole. Secure hardware from

below sink. Install stopper (M1) in

the removable or non-removable

position.

2

3

M7

PIVOT

M2

M1

5) Attach inner washer (M8), pivot

rod (M9) and outer washer (M10)

to tailpiece (M7). Hand tighten nut

(M11) to secure pivot rod (M9).

M9

M7

1

M8

M10

M11

2

6) Connect lift rod (E) to clevis strap

(M13) and secure with thumb

screw (M14). Insert pivot rod

(M9) through spring clip (M12)

and clevis strap (M13). Secure

with spring clip (M12) and adjust

linkage if necessary.

3

4

M12

M9

M13

2

M14

M13

1

E

Installation

DO NOT use pipe dope

or thread sealant on drain

assembly, or any plastic

threaded components.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621

Troubleshooting Chart

Finish is spotting.

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

7) Attach supply lines to 1/2” IPS inlet

connections on faucet body (H).

Using a wrench, nish with one half

turn. DO NOT overtighten.

1

2

I

Maintenance

1) Remove plug button (C) and

set screw (B). Turning counter-

clockwise, disassemble handle

(A), collar (D) and nut (F) from

cartridge (G).

B

C

A

D

F

G

2) Remove cartridge (G) from faucet

body (H). Inspect for debris.

Replace cartridge if necessary.

G

H

3) Correctly align cartridge (G) and

insert into faucet body (H). Install

handle assembly following step 1

in reverse.

1

4

2

H

8) Attach supply lines to shut-off

valves and hand tighten. Using a

wrench, nish with one-half turn.

DO NOT overtighten.

1

2

9) Remove aerator (I) and ush lines

free of debris. Check for leaks.

H

B

C

A

D

F

G

1

Installation

Note: Counterclock-

wise to lower tem-

perature, clockwise

to increase tempera-

ture.

Page is loading ...

Symmons S-6612-STN-1.0 Installation guide

Symmons S-6612-STN-1.0 Installation guide

in other languages

Related papers

Other documents