Real Fyre G31 Owner's manual

Brand: Real Fyre

Model: G31

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

G31 Series Burner

REV 6 - 1703211515

L-A2-353

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

The Real Fyre burner system is to be installed only in

a solid-fuel burning ﬁ replace with a working ﬂ ue and

constructed of noncombustible material. The installation,

including provisions for combustion and ventilation air

must conform with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or the CSA B149.1, Natural Gas

and Propane Installation Code, and applicable local

building codes.

A damper clamp is included to maintain the minimum

permanent vent opening and to prevent full closure

of the damper blade. The chimney damper MUST

be fully opened when burning the unit. The unit is

designed to burn with yellow ﬂ ames; thus adequate

ventilation is absolutely necessary.

To comply with certification, listings, and building

code acceptances, and for safe operation and proper

performance of this burner system, use ONLY Peterson

parts and accessories. Use of other controls, parts,

and accessories that are not designed for use with

Real Fyre burner systems is prohibited and will void

all warranties, certiﬁ cations, listings, and building code

approvals, and may cause property damage, personal

injury, or loss of life. Peterson will not be liable for any

damages caused by this misuse.

*Note: Solid-fuels shall not be burned in a ﬁ replace

where a decorative appliance is installed.

FOR INSTALLATION IN

SOLID-FUEL BURNING

FIREPLACES*

IMPORTANT: READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF THE UNIT.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier

from a neighbor’s phone. Follow gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁ re department.

WARNING

If the information in this manual is not

followed exactly, a fire or explosion

may result, causing property damage,

personal injury, or loss of life.

This appliance is only for use with the type

of gas indicated on the rating plate.

Installation and service must be performed

by a qualified professional installer,

service agency, or the gas supplier.

DESIGN CERTIFIED

Vented Decorative Appliance

ANSI Z21.60-2012

CSA 2.26-2012

12-086

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

G31 TRIPLE BURNER VENTED SYSTEMS

Regulated burner

system for use with

propane or natural gas

INSTALLATION &

OWNER’S MANUAL

Burner Systems:

G31- ** -(P)A

G31- ** -17(P)

G31- ** -2V(P)T

G31- ** -02(P)

** Sizes:

(18/20, 24/30, 33/39)

Page is loading ...

REV 6 - 1703211515

L-A2-353

TABLE OF CONTENTS

GETTING STARTED

IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION ...........................................5

FIREPLACE OPERATING SAFETY INFORMATION .......................................................................................7

SPECIFICATIONS............................................................................................................................................8

DAMPER CLAMP INSTRUCTIONS ............................................................................................................. 10

BURNER PARTS LIST - MANUAL PILOT (A) SERIES ..................................................................................11

BURNER PARTS LIST - 17 SERIES .............................................................................................................. 12

BURNER PARTS LIST - 2VT SERIES ........................................................................................................... 13

BURNER PARTS LIST - 02 SERIES .............................................................................................................. 14

LOGS PARTS LIST ....................................................................................................................................... 15

INSTALLATION

INSTALLATION ........................................................................................................................................... 17

BURNER INSTALLATION .......................................................................................................................... 17

LIGHTING TEST ...................................................................................................................................... 18

LOG SET AND EMBERS PLACEMENT [MC(O,S) log sets] .............................................................................. 19

INSTALLING/REPLACING BATTERIES (if applicable) ................................................................................. 22

REMOTE TRANSMITTER BATTERY ............................................................................................................ 22

RECEIVER/SWITCH BOX BATTERIES ......................................................................................................... 22

USE, CARE, & SERVICE

LIGHTING INSTRUCTIONS - MANUAL PILOT (A) SERIES ....................................................................... 23

FOR YOUR SAFETY, READ BEFORE LIGHTING .......................................................................................... 23

LIGHTING THE PILOT ............................................................................................................................. 23

LIGHTING THE BURNER ......................................................................................................................... 25

SHUTTING DOWN ................................................................................................................................... 25

PILOT BURNER CHECK/ADJUSTMENT ..................................................................................................... 25

LIGHTING INSTRUCTIONS - 17 SERIES ..................................................................................................... 27

FOR YOUR SAFETY, READ BEFORE LIGHTING .......................................................................................... 27

LIGHTING THE PILOT ............................................................................................................................. 27

REMOTE LIGHTING ................................................................................................................................ 27

MANUAL LIGHTING ................................................................................................................................ 29

SHUTTING DOWN ................................................................................................................................... 31

PILOT BURNER CHECK/ADJUSTMENT ..................................................................................................... 31

REMOTE OPERATING INSTRUCTIONS - 17 SERIES .................................................................................. 31

ORIENTATION ........................................................................................................................................ 31

FLAME HEIGHT ..................................................................................................................................... 31

LIGHTING INSTRUCTIONS - 2VT SERIES .................................................................................................. 33

FOR YOUR SAFETY, READ BEFORE LIGHTING .......................................................................................... 33

REMOTE LIGHTING ................................................................................................................................ 33

MANUAL LIGHTING ................................................................................................................................ 35

SHUTTING DOWN ................................................................................................................................... 35

PILOT APPEARANCE ............................................................................................................................... 35

REMOTE OPERATING INSTRUCTIONS - 2VT SERIES ............................................................................... 37

ORIENTATION ........................................................................................................................................ 37

FLAME HEIGHT ..................................................................................................................................... 37

LIGHTING INSTRUCTIONS - 02 SERIES ..................................................................................................... 39

FOR YOUR SAFETY, READ BEFORE LIGHTING .......................................................................................... 39

REMOTE LIGHTING ................................................................................................................................ 39

MANUAL LIGHTING ................................................................................................................................ 41

SHUTTING DOWN ................................................................................................................................... 41

PILOT APPEARANCE ............................................................................................................................... 41

CLEANING AND SERVICING ...................................................................................................................... 43

SYNCING THE REMOTE SYSTEM (if applicable) ........................................................................................... 44

FLAME DESCRIPTION ................................................................................................................................ 44

TROUBLESHOOTING .................................................................................................................................. 45

ELECTRONIC PILOT TROUBLESHOOTING (IF APPLICABLE) .................................................................. 47

WARRANTY ................................................................................................................................................ 48

Page is loading ...

IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION

A. BE CAREFUL: If not installed, serviced, and used correctly per these instructions, this product can cause serious

personal injury, property damage, or loss of life.

B. WARNING: Before installing in a solid-fuel-burning ﬁ replace, the chimney ﬂ ue, damper, and ﬁ rebox must be thoroughly

CLEANED of soot, creosote, ashes, and loose paint, and must be inspected by a qualiﬁ ed chimney cleaner. Some older

ﬁ replaces may need repair prior to installing this appliance.

C. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is NOT FIELD CONVERTIBLE

for use with other gasses.

CHECK GAS TYPE (natural or L.P.): The gas supply must be the same as stated on your burner system rating plate. If

gas supply is different, DO NOT INSTALL. Contact your dealer for immediate assistance.

D. INSUFFICIENT GAS PRESSURE WILL KEEP THE PILOT (IF EQUIPPED) FROM OPERATING PROPERLY.

DO NOT USE IF GAS PRESSURE IS LOWER THAN THE MINIMUM REQUIREMENT.

E. The minimum inlet gas-supply pressure for purposes of input adjustment is 5" water column (w.c.) on natural gas and

11" w.c. on L.P. gas. Insufﬁ cient gas pressure will affect proper operation of the pilot (if equipped). Do not install this gas

appliance if minimum pressure is not available. The maximum inlet gas-supply pressure is 10.5" w.c. on natural gas and

13" w.c. on L.P. gas. The L.P. source must be regulated. (Do not connect this appliance directly to an unregulated

L.P. gas tank - this can cause an explosion.) Do not connect this appliance to a portable L.P. gas cylinder.

F. The gas piping system must be sized to provide minimum inlet pressure at the maximum ﬂ ow rate (BTU/hr).

Undue pressure loss will occur if the pipe is too small, or the run is too long. Gas supply pipe must be

" minimum

interior diameter. If the gas line is longer than 20', a larger diameter line may be necessary. Refer to the NFPA 54

guidelines for further details.

G. Input ratings shown in BTU per hour are for elevations up to 2,000 ft. For elevations above 2,000 ft., refer to the National

Fuel Gas Code or contact manufacturer before installing this product.

H. This gas appliance and its main gas valve must be disconnected from the gas-supply piping system during any pressure

testing of that system at test pressures in excess of

psig.

I. This gas appliance must be isolated from the gas-supply piping system by closing the equipment shutoff valve connected to

the gas-supply line during any pressure testing of the gas-supply piping system at test pressures equal to or less than

psig.

J. To install the gas appliance in your ﬁ replace, the ﬁ replace MUST meet the minimum size requirements (see

product speciﬁ cations table in SPECIFICATIONS section).

K. This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where not prohibited

by local codes. Installation of appliances designed for manufactured home (U.S. only) or mobile home installation must

conform with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/

NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard.

L. DO NOT install this burner system if the ﬁ replace hearth is recessed. The ﬁ replace ﬂ oor must be at the same level

as or higher than the ﬁ replace front opening. If glass doors are used: the ﬁ replace ﬂ oor must not be blocked by the door

frame; the frame must have openings to allow for fresh air circulation. See the SPECIFICATIONS section for details.

CAUTION: Installation and repair must be done by an NFI Certiﬁ ed or other qualiﬁ ed professional installer.

Installer: Carefully read these instructions before installing this gas burner system. Be sure you understand

all safety precautions and warnings contained in this manual.

Page is loading ...

FIREPLACE OPERATING SAFETY INFORMATION

A. Adults shall be present when this gas appliance is operating. This unit shall not be left burning when unattended or

while anyone is sleeping.

B. Keep the area of the gas burner system clear and free from combustible materials, gasoline, and other ﬂ ammable

vapors and liquids.

C. DO NOT use this appliance if any part has been underwater. Immediately call a qualiﬁ ed service technician to inspect

the appliance and to replace any part of the control system and any gas control that has been underwater. Attempted

operation may result in ﬁ re or explosion resulting in property damage, personal injury or loss of life.

D. A ﬁ replace screen must be in place when the system is burning. Provisions for adequate combustion air must be

maintained. Unless other provisions for combustion air are provided, the screen shall have an opening(s) for introduction

of combustion air. Combustion air is adequate when all ﬂ ames curl into the ﬁ replace and away from the screen. When

a glass ﬁ replace enclosure (door) is used, leave the doors fully open when the system is in operation.

E. Do not remove the rating plates or the warning tags. These are an integral safety and identiﬁ cation component of this

appliance.

F. Be sure to read the CLEANING AND SERVICING and FLAME DESCRIPTION sections.

Real Fyre gas burner systems must be installed only in a wood burning ﬁ replace with the minimum

ﬁ rebox dimensions and venting requirements met (see table on this page). This appliance is designed

to burn with yellow ﬂ ames; adequate ventilation is absolutely necessary.

SPECIFICATIONS

Table 1 - Product Speciﬁ cations

Fireplace Floor Requirement

DO NOT install this burner system if the ﬁ replace hearth is recessed. The ﬁ replace ﬂ oor must be at

the same level as or larger than the ﬁ replace front opening. An ash lip or recess may not exceed

". See

Fig. 8-1 below.

Note: If glass doors are used: the ﬁ replace ﬂ oor must not be blocked by the door frame; the frame must

have openings to allow for fresh air circulation.

Product Speciﬁ cations

Fig. 8-1

Fireplace

ﬂ oor

Fireplace

opening

(burner

system)

ASH LIP OR

RECESS

ABOVE

/4"

NOT

PERMITTED

Max.

ASH LIP OR

RECESS UP

/4"

PERMITTED,

Speciﬁ cation Value Qty.

02 burner system battery type D battery 2

2VT burner system battery type AA battery 4

Remote transmitter battery type 12V battery 1

Remote receiver battery type AA battery 4

Table 2 - Technical Data (if applicable)

Burner

Model

Dimensions BTU Rating

Width *

Depth Height

Nat. Gas L.P. Gas

Front Rear

High

Setting

Low

Setting †

High

Setting

Low

Setting †

G31-18/20 (18" log set) 25" 20" 15" 16" 55k 20k 40k 21k

G31-24/30 (24" log set) 35" 25" 15" 16" 65k 21k 50k 22k

G31-24/30 (30" log set) 39" 28" 15" 16" 65k 21k 50k 22k

G31-33/39 (33" log set) 44" 32" 15" 16" 75k

†

/ 85k 22k 60k 23k

G31-33/39 (39" log set) 47" 32" 15" 16" 75k

†

/ 85k 22k 60k 23k

* For 02 models, add 2" to both front and rear width

† 2VT models only

Note: Rear width is at corresponding depth.

SPECIFICATIONS (cont.)

17 SERIES WIRING DIAGRAM

Fig. 9-1

Remote

receiver

Inlet

Valve

Outlet

02 SERIES WIRING DIAGRAM

Fig. 9-2

Remote

receiver

Valve

Ignition

module

Wire

harness

Battery

box

Ground

wire

2VT SERIES WIRING DIAGRAM

Valve

Motor wire

harness

Battery

pack

Ignition

module

Fig. 9-3

Insulated copper

Black

Main wire

harness

White

Green

Orange

Red

Black

Main

Gas

inlet

Step motor

main ﬂ ame

(Main gas out)

(Pilot gas out)

Main ﬂ ame

step output

Copper

Black

(GND)

Thermocouple

line

Pilot

assembly

Pilot

assembly

Pilot

assembly

Electrode

wires

Wire

harness

Damper clamp

Set screw

Open

Closed

DAMPER CLAMP INSTRUCTIONS

Fig. 10-1 Damper clamp detail

Fig. 10-2 Damper open / closed

The damper clamp with hex bolt (

Fig. 10-1) is provided as a

means to prevent full closure of the damper blade. The clamp is

easily attached to most damper blades with pliers or a wrench,

and must be permanently installed. The clamp is designed

to prevent accidental closure of the damper when installed

as illustrated (Fig. 10-2). Should the clamp not ﬁ t, or fail to

provide the permanent vent opening listed in Table 3 below,

have a permanent stop installed, remove the damper blade,

or have the damper cut to provide the minimum permanent

opening required.

Minimum permanent free opening area of chimney damper for venting (sq. in.)

For factory-built ﬁ replaces

Chimney height 18/20" 24/30" 33/39"

15' 24 30 42

20' 20 25 35

30' 16 19 27

For masonry-built ﬁ replaces

15' 35 41 52

20' 32 37 47

30' 29 34 43

Note: The minimum chimney height from hearth to top of chimney is 15'.

Table 3 - Minimum Chimney Damper Venting Requirements

Venting Requirements

THE DAMPER MUST BE COMPLETELY OPENED WHEN OPERATING THIS GAS APPLIANCE TO

ACHIEVE THE BEST VENTILATION POSSIBLE.

THESE ARE MINIMUM DAMPER OPENING SPECIFICATIONS.

BURNER PARTS LIST - MANUAL PILOT (A) SERIES

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

24/30" burner model shown

Bottom view

Pilot

Thermocouple

18/20" model 24/30" model 33/39" model

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Pilot assembly (natural)

Pilot assembly (propane)

PAC-1NAT

PAC-1LP

PAC-1NAT

PAC-1LP

PAC-1NAT

PAC-1LP

2. Control valve (natural or propane models) SV-19 1 SV-19 1 SV-19 1

Valve extension kit

(includes extension rod, knob, bracket, and nut)

EH-12 1 EH-12 1 EH-12 1

4. Flex connector (w/ adapter), 1/2" O.D. x 24" CK-5-24SP 1 CK-5-24SP 1 CK-5-24SP 1

5. Lava fyre coals LFC-6 1 LFC-6 1 LFC-6 1

6. Lava granules LF-5 1 LF-5 1 LF-5 1

7. Glowing embers EM-21B 1 EM-21B 2 EM-21B 3

8. Bryte coals EM-11 1 EM-11 1 EM-11 2

9. Damper clamp DC-1 1 DC-1 1 DC-1 1

Flash tube

BURNER PARTS LIST - 17 SERIES

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

Bottom view

Pilot

Thermocouple

Remote transmitter and receiver

batteries included with burner system.

18/20" model 24/30" model 33/39" model

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Pilot assembly (natural)

Pilot assembly (propane)

PAC-1NAT

PAC-1LP

PAC-1NAT

PAC-1LP

PAC-1NAT

PAC-1LP

2. Control valve (natural or propane models) SV-37 1 SV-37 1 SV-37 1

Valve extension kit

(includes extension rod, knob, bracket, and nut)

EH-12 1 EH-12 1 EH-12 1

Remote kit

(includes receiver, transmitter, batteries,

and plastic cover)

VR-1A 1 VR-1A 1 VR-1A 1

5. Remote transmitter (only) AT-V1-1 1 AT-V1-1 1 AT-V1-1 1

6. Decorative heat shield HS-36 1 HS-36 1 HS-36 1

7. Flex connector (w/ adapter), 1/2" O.D. x 24" CK-5-24SP 1 CK-5-24SP 1 CK-5-24SP 1

8. Lava fyre coals LFC-6 1 LFC-6 1 LFC-6 1

9. Lava granules LF-5 1 LF-5 1 LF-5 1

10. Glowing embers EM-21B 1 EM-21B 2 EM-21B 3

11. Bryte coals EM-11 1 EM-11 1 EM-11 2

12. Damper clamp DC-1 1 DC-1 1 DC-1 1

24/30" burner model shown

Flash tube

BURNER PARTS LIST - 2VT SERIES

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

Bottom view

18/20" model 24/30" model 33/39" model

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Pilot assembly (natural)

Pilot assembly (propane)

PAC-12

PAC-12P

PAC-12

PAC-12P

PAC-12

PAC-12P

Control valve (natural)

Control valve (propane)

SV-47

SV-47P

SV-47

SV-47P

SV-47

SV-47P

3. Control module / remote receiver IMP-6 1 IMP-6 1 IMP-6 1

4. Main & motor harness assembly WH-02 1 WH-02 1 WH-02 1

5. Battery box BAT-02 1 BAT-02 1 BAT-02 1

Switch box assembly

(includes battery box, switch, heat shield)

SBA-02 1 SBA-02 1 SBA-02 1

7. Decorative heat shield HS-42 1 HS-42 1 HS-42 1

8. Flex connector (w/ adapter), 1/2" O.D. x 24" CK-5-24SP 1 CK-5-24SP 1 CK-5-24SP 1

9. Remote transmitter (only) AT-2VA-1 1 AT-2VA-1 1 AT-2VA-1 1

10. Lava fyre coals LFC-6 1 LFC-6 1 LFC-6 1

11. Lava granules LF-5 1 LF-5 1 LF-5 1

12. Glowing embers EM-21B 1 EM-21B 2 EM-21B 3

13. Bryte coals EM-11 1 EM-11 1 EM-11 2

14. Damper clamp DC-1 1 DC-1 1 DC-1 1

Pilot

Electrode

Thermocouple

Remote transmitter and switch box

batteries included with burner system.

24/30" burner model shown

Flash tube

BURNER PARTS LIST - 02 SERIES

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

Bottom view

18/20" model 24/30" model 33/39" model

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Pilot assembly (natural)

Pilot assembly (propane)

PAC-6

PAC-7

PAC-6

PAC-7

PAC-6

PAC-7

Control valve (natural)

Control valve (propane)

SV-45

SV-45P

SV-45

SV-45P

SV-45

SV-45P

3. Control module IMP-1 1 IMP-1 1 IMP-1 1

4. Main harness assembly WH-03 1 WH-03 1 WH-03 1

Remote receiver box

(includes remote receiver, battery box, metal heat

shield assy, wire harness)

AR-02-1 1 AR-02-1 1 AR-02-1 1

6. Remote transmitter (only) AT-R1-1 1 AT-R1-1 1 AT-R1-1 1

7. Decorative heat shield HS-37 1 HS-37 1 HS-37 1

8. Flex connector (w/ adapter), 1/2" O.D. x 24" CK-5-24SP 1 CK-5-24SP 1 CK-5-24SP 1

9. Lava fyre coals LFC-6 1 LFC-6 1 LFC-6 1

10. Lava granules LF-5 1 LF-5 1 LF-5 1

11. Glowing embers EM-21B 1 EM-21B 2 EM-21B 3

12. Bryte coals EM-11 1 EM-11 1 EM-11 2

13. Damper clamp DC-1 1 DC-1 1 DC-1 1

Pilot

Electrode

Flame sensor

Remote transmitter and switch box

batteries included with burner system.

24/30" burner model shown

batteries incl

Flash tube

MC(O,S)-18 Log Sets

Mountain Crest Oak (MCO) Mountain Crest Split (MCS)

Item Description Part No. Qty. Part No. Qty.

1. Rear log MCOL-16BR 1 MCOL-16BR 1

2. Front log MCOL-18BF 1 MCSL-18BF 1

3. Center middle log MCOL-14TC 1 MCSL-14TC 1

4. Left top log MCOL-10TL 1 MCSL-10TL 1

5. Right top log MCOL-12TR 1 MCSL-12TR 1

6. Center top log MCOL-9T 1 MCSL-9T 1

LOGS PARTS LIST

MCO-18

Log Set Shown

MC(O,S)-(24,30) Log Sets

Mountain Crest Oak (MCO) Mountain Crest Split (MCS)

Item Description Part No. Qty. Part No. Qty.

24" Rear log

30" Rear log

MCOL-20BR

MCOL-24BR

MCOL-20BR

MCOL-24BR

24" Front log

30" Front log

MCOL-24BF

MCOL-30BF

MCSL-24BF

MCSL-30BF

3. Center middle log MCOL-14TC 1 MCSL-14TC 1

4. Left top log MCOL-11TL 1 MCSL-11TL 1

5. Right top log MCOL-15TR 1 MCSL-15TR 1

6. Center top log MCOL-10T 1 MCSL-10T 1

MCOL 1

MCO-24

Log Set Shown

MC(O,S) log sets are designed exclusively for placement on G31 burner systems and are addressed in

this manual.

Additional common log sets are available: CHB, CHD, CHAO, CHS, CHNA, CHNS series.

If a common log set is purchased, follow the G31 supplemental instructions supplied with this burner

system. (Disregard the common log placement instructions packed with the log set.)

LOGS PARTS LIST (cont.)

Note: The log set is purchased and packaged separately.

MCO-33

Log Set Shown

MC(O,S)-(33,39) Log Sets

Mountain Crest Oak (MCO) Mountain Crest Split (MCS)

Item Description Part No. Qty. Part No. Qty.

1. Rear log MCOL-28BR 1 MCOL-28BR 1

33" Front log

39" Front log

MCOL-33BF

MCOL-39BF

MCSL-33BF

MCSL-39BF

3. Left middle log MCOL-10T 1 MCSL-10T 1

4. Center middle log MCOL-15TY 1 MCSL-15TY 1

5. Right middle log MCOL-10TR 1 MCSL-10TR 1

6. Left top log MCOL-13T 1 MCSL-13T 1

7. Center top log MCOL-11TL 1 MCSL-11TL 1

8. Right top log MCOL-15T 1 MCSL-15T 1

REFER TO THE PARTS LIST WHEN FOLLOWING THESE

INSTRUCTIONS.

24" 02 burner model shown here.

BURNER INSTALLATION

1. MAKE SURE THE FIREPLACE GAS SUPPLY IS TURNED OFF.

2. Locate the gas-supply stub inside the ﬁ replace and remove the

cap, if attached (reference Fig. 17-1).

CAUTION: When removing the cap, make sure the stub does not

turn, loosening the connection inside the wall.

3. Place the burner system in the ﬁ replace. Center the burner from

left to right in the ﬁ replace. (Reference Fig. 17-2 for orientation.)

Note: Ensure the porcelainized panel is clean of all dust. Use a

clean soft cloth if necessary. See Fig. 17-3.

4. Be sure gas to the ﬁ replace is off. Remove the adapter

connected to the ﬂ ex connector (pre-installed on the burner

system). Attach the adapter to the gas-supply stub using a pipe

compound resistant to all gasses. Tighten securely. Then attach

the open end of the ﬂ ex connector to the adapter. Tighten securely

(see Fig. 17-1).

5. LEAK TEST: Turn on the ﬁ replace gas supply, and test at all

connections for leaks using the appropriate soapy water solution.

If bubbles appear, a leak is present. Turn off the gas and tighten

at all connections. Repeat until no leaks are present. If a leak

persists, turn off the gas supply and contact the local gas company

or dealer. NEVER USE A FLAME TO CHECK FOR LEAKS.

For manual pilot models, continue to the following section.

6. At this stage the burner system batteries are to be installed

(if applicable). Reference the INSTALLING/REPLACING

BATTERIES section for details.

7. Remote Receiver (17 models)

Place the plastic cover over the receiver. Then place on its side,

at the rear left corner of the ﬁ replace. Place as far from the burner

system as possible. See Fig. 17-2 & Fig. 17-4.

Remote Receiver/Switch Box (02 & 2VT models)

Place on its side, at the rear left corner of the ﬁ replace. It

should rest with its bottom as near as possible and facing the

ﬁ replace wall. It must not be placed directly next to the burner

pan area to avoid damage to the batteries (and remote receiver

- 02 models). See Fig. 17-2 & Fig. 17-4.

Important: Ensure that the box wire remains away from the burner

system and its ﬂ ame during operation.

The Real Fyre burner system must be installed by a qualiﬁ ed professional service technician. Instructions

must be followed carefully to ensure proper performance and full beneﬁ t from the burner system. Check to be

sure the burner system is designed and labeled for the type of gas (natural or propane gas) supplied to

the ﬁ replace. Fireplace ﬂ oor must be level, clean, and smooth (see FIREPLACE SAFETY INFORMATION

section).

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts

speciﬁ cally approved with this appliance may result in property damage or personal injury.

INSTALLATION

Fig. 17-2 Place receiver/switch box

Fig. 17-1 Connect gas supply

Flex connector

Adapter

Gas supply stub

Fig. 17-3 Ensure a clean panel

Keep clean and DO NOT

cover with embers

(02 model shown here)

Fig. 17-4 Proper receiver/box placement

Place

receiver/switch box:

• Rear left corner,

on side,

• exposed side against

ﬁ replace wall

DO NOT

place box

in this area

Place receiver or receiver/switch box

Place receiver:

• Rear left corner

• Ensure plastic

cover is in place

IMPORTANT

For all valves, the air MUST be purged from the gas line before the pilot will light and burn properly. The time

needed to purge will depend on the length of the gas line to the unit and the amount of time since the unit or

gas line was last used. It may take several minutes before all the air is purged and the pilot will light and burn

properly. Reference the LIGHTING INSTRUCTIONS section in this manual.

INSTALLATION (cont.)

8. Decorative Heat Shield (remote models only)

Place the decorative heat shield over the remote receiver/

switch box as shown in Fig. 18-1.

LIGHTING TEST

Prior to proceeding with installation, perform a lighting test

(see lighting instructions for lighting your burner). Allow the

unit to completely cool after testing.

LAVA GRANULES/COALS (DECORATIVE)

1. Spread the supplied lava granules on the ﬂ oor of the

ﬁ replace, around the front and sides of the burner system

(see Fig. 18-2). The lava granules may be placed around

the receiver/switch box. Leave the front of the receiver/

switch box clear for control access.

2. Repeat this process for the supplied lava coals (on top of

the already placed lava granules).

Note: DO NOT place any lava media on the burner system,

or behind it.

Fig. 18-2 Place lava media

Fig. 18-1 Place heat shield (if applicable)

Must rest on ﬂ oor and at rear corner

INSTALLATION (cont.)

CAUTION: BURN HAZARD! Logs will remain hot for some time after use. If you need to reposition

any log to maintain the proper layout, use heat-resistant gloves or allow logs adequate time

to cool before handling.

Place the rear log (log #1) as shown. The log should

rest ﬂ at between the rear brackets and top burner.

Embers

Place the remaining glowing embers evenly in the

area along the front log as shown.

Store any excess embers if applicable.

Generic Placement Steps

Important: DO NOT place any embers on top of the ﬂ ash tube to ensure proper operation.

All models begin with the log and ember placement shown below. Continue with the appropriate section (on one of the

following pages) speciﬁ c to your log set size.

Embers

DO NOT place any embers on top of the ﬂ ash tube

to ensure proper operation. Keep the area shown

above clear at all times.

Place the supplied glowing embers evenly in the

areas shown. Break up any clumps that may have

developed during shipment. Keep some embers

for future placement along the front log.

You must position and maintain the log layout as shown here to ensure optimal operation of the burner system.

24" log set shown below for generic placement steps. Final steps are separated by log set sizes. Do not add

any additional embers to this log set. Any additional embers may cause unsafe operation. MCO log sets

shown. Design may vary slightly; placement is the same.

LOG SET AND EMBERS PLACEMENT [MC(O,S) log sets]

Log placement shown here is for MC(O,S) log sets. If a different log set has been purchased, follow

the G31 supplemental instructions supplied with this burner system. (Disregard the common log

placement instructions packed with the log set.)

Keep ﬂ ash

tube clear

(ﬂ ash tube)

Place the front log (log #2) as shown. Rest the log

with its back against the burner assembly behind it.

DO NOT place it forward or on top of the grate

ﬁ ngers.

(ﬂ ash tube)

Ember placement detail.

Keep ﬂ ash

tube clear

Embers

INSTALLATION (cont.)

18", 24" & 30" Log Sets Only

For 18", 24", & 30" log sets, continue with the steps below to complete placement.

For 33" & 39" log sets, proceed to the following page.

Bryte Coals

Separate half of the supplied bryte coals into small

pieces, and evenly place them over the glowing

embers in the middle ember bed as shown.

Bryte Coals

Separate the remaining (second half) of bryte coals

into small pieces, and evenly place them over the

glowing embers in the bottom ember bed as shown.

Place the center top log (log #6) as shown. It

will rest on the front log and in the groove of the

center log below.

Place the left and right top logs (logs #4 & #5) as

shown. They will rest in the grooves found on the

logs below.

Place the center middle log (log #3) as shown. It

will rest in the grooves found on the logs below.

Generic Placement Steps (cont.)

To complete log placement continue to the appropriate section speciﬁ c to your log set size.

33" & 39" Log Sets Only

For 33" & 39" log sets, continue with the steps below to complete placement.

For 18", 24", & 30" log sets, go back to the previous page.

INSTALLATION (cont.)

Place the left and center middle logs (logs #3 & #4)

as shown. They will rest in the grooves found on the

logs below.

Place the right middle log (log #5) and the left top log

(log #6) as shown. They will rest in the grooves found

on the logs below.

Place the center and right top logs (logs #7 & #8) as

shown. They will rest in the grooves found on the logs

below.

INSTALLING/REPLACING BATTERIES (IF APPLICABLE)

CAUTION: Ensure the unit is connected to the gas line and has

been tested for leaks before you insert batteries.

CAUTION: Turn off the remote and/or burner and allow the unit

to completely cool prior to any battery replacements.

Important: Low/dead batteries will affect burner system

operation. Replace batteries any time the burner

will not turn on.

REMOTE TRANSMITTER BATTERY

The remote transmitter requires one 12V battery to operate (included).

Locate the transmitter, remove the lid (found on rear), and properly

insert the new battery as marked. Re-secure the lid. See Fig. 22-1.

RECEIVER/SWITCH BOX BATTERIES

Important: Always replace the decorative heat shield over

the receiver or receiver/switch box after battery

replacement.

Remote receiver

02 models

The remote receiver requires 4 AA batteries to operate (included).

Locate the remote receiver box and turn it over. Use a Phillips

screwdriver to remove the screw found on the side of the box, then

remove the bracket. Remove the receiver from the box and turn it

over. Slide open the lid, and properly insert the new batteries as

marked. See Fig. 22-2 (also reference Fig. 22-3).

Replace the lid and replace the remote receiver onto the Velcro in

the remote receiver box. Then replace the bracket using the screw

and re-position the box in the ﬁ replace.

17 models

The remote receiver requires 4 AA batteries to operate (included).

Locate the remote receiver and turn it over. Slide open the lid, and

properly insert the new batteries as marked. See Fig. 22-2.

Replace the lid, then re-position the remote receiver in the ﬁ replace.

(Ensure the plastic cover is properly in place over the receiver.)

Receiver/Switch Box

02 models

The burner system requires 2 D batteries to operate (included). Locate

the remote receiver box and turn it over. Use a Phillips screwdriver

to remove the screw found on the side of the box, then remove the

bracket. Properly insert the new batteries as marked. See Fig. 22-3.

Replace the bracket using the screw and re-position the remote

receiver box in the ﬁ replace.

2VT models

The burner system requires 4 AA batteries to operate (included).

Locate the switch box and turn it over. Detach the battery box from

the Velcro. Use a small Phillips screwdriver to remove the screw

found on the bottom of the battery box, then remove the battery lid.

Properly insert the new batteries as marked. See Fig. 22-3.

Replace the battery lid using the screw, replace the battery box onto

the Velcro, and re-position the switch box in the ﬁ replace.

Fig. 22-1 Transmitter battery

Remove

lid for

12V

battery

access

AA batteries

Fig. 22-2 Remote receiver batteries

(17 model shown)

AA batteries

Fig. 22-3 Receiver/switch box batteries

2VT model

02 model

D batteries

Brackets

Screws

Remote

receiver

PILOT

OFF

PILOT

OFF

PILOT

OFF

PILOT

FOR YOUR SAFETY, READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion may result causing

property damage, personal injury or loss of life.

A. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in

or turn by hand, don't try to repair it. Call a qualiﬁ ed professional service technician. Excessive force or

attempted repair may result in ﬁ re or explosion.

B. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the ﬂ oor

because some gas is heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

• Do not light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the ﬁ re department.

C. The burner system has a pilot that can be lit by hand using a long ﬁ replace match or lighter. When lighting

the pilot, follow these instructions exactly.

D. Do not use this appliance if any part has been underwater. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been

underwater. Attempted operation may result in ﬁ re or explosion resulting in property damage, personal

injury or loss of life.

LIGHTING THE PILOT

1. Locate the valve on the side of the unit. Push in the

gas control knob slightly and turn clockwise to OFF

(Fig. 23-1).

Note: The control knob cannot be turned from PILOT

to OFF unless the knob is pushed in slightly. Do

not force.

Allow ﬁ ve (5) minutes for any gas in the unit to dissipate.

IF YOU SMELL GAS, SEE STEP B ABOVE. If you don’t

smell gas, go on to step 2.

2. Turn the control knob counterclockwise to PILOT

(Fig. 23-1). Push the control knob ﬁ rmly and fully

in and hold. Hold a long ﬁ replace match or lighter

near the thermocouple to light the pilot. Continue to

hold the control knob in for approximately 60 seconds

after the pilot is lit, then release the knob. The pilot

will remain lit.

WARNING: If the pilot fails to light repeat steps 1

and 2.

If the pilot fails to light after several tries, turn the control

knob to OFF and contact a qualiﬁ ed professional service

technician.

Fig. 23-1 Control knob detail (OFF, PILOT)

1. Turn knob

clockwise to OFF

prior to lighting

the pilot.

LIGHTING INSTRUCTIONS - MANUAL PILOT (A) SERIES

2. Turn knob

counterclockwise to

PILOT position. With

match ready, press

knob in and hold for

60 seconds while

lighting pilot.

Page is loading ...

Real Fyre G31 Owner's manual

Brand: Real Fyre

Model: G31

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

G31 Series Burner

Download PDF

report

in other languages

français: Real Fyre G31 Le manuel du propriétaire

Real Fyre G31 Owner's manual

This manual is also suitable for

Real Fyre G31 Owner's manual

in other languages

Related papers

Other documents