American Standard T203.730 User manual

American Standard
Brand
American Standard
Model
T203.730
Category
Sanitary ware
Type
User manual

American Standard T203.730 is a central thermostat without volume control. It has a maximum mixed water temperature of 109°F, which can be adjusted to 104°F or 112°F. The thermostat also features a red stop button that allows the user to increase the mixed water temperature up to the maximum limit. The thermostat comes with an escutcheon holder, escutcheon, dial plate, screw, cap, temperature control handle, and handle cap. To install the thermostat, the user will need a flat blade screwdriver and a Phillips screwdriver.

American Standard T203.730 is a central thermostat without volume control. It has a maximum mixed water temperature of 109°F, which can be adjusted to 104°F or 112°F. The thermostat also features a red stop button that allows the user to increase the mixed water temperature up to the maximum limit. The thermostat comes with an escutcheon holder, escutcheon, dial plate, screw, cap, temperature control handle, and handle cap. To install the thermostat, the user will need a flat blade screwdriver and a Phillips screwdriver.

CENTRAL THERMOSTAT
LESS VOLUME CONTROL
TRIM KIT
Installation
Instructions
M968682
T203.730
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
ROUGHING-IN DIMENSIONS
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth
(as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
T
O
P
/
O
B
E
N
168mm
(6-5/8)
232mm
(9-1/8)
86mm
(3-3/8)
34mm
(1-3/8)
180mm
(7-1/8)
150mm
(5-7/8)
48mm to 68mm
(2 to 2-5/8)
R510
1/2 NPT
R530
3/4 NPT
R510
1/2 NPT
R530
3/4 NPT
25mm
(1)
1
1
3
5
2
4
1
3
4
M968682
TEMPERATURE CALIBRATION
SET HOT LIMIT STOP
5
Check that arrow marking B points vertically upwards. If not, push the BLACK
CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3)
and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards.
For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout
temperature is 100˚F. Check that arrow marking A on the KNOB MOUNT (3) still points
upward after adjusting the thermostat to 100˚F. If not, pull out the RED LOCKING DEVICE (5).
Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow.
Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards.
The maximum mixed water temperature is set at 109˚F at the factory.
This setting can be changed if desired.
Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part).
Reinstall it at the desired notch as indicated in the diagram to limit the maximum
mixed water temperature to 104˚F or 112˚F.
Reinstall RED LOCKING DEVICE (5).
ARROW
"A"
ARROW
"B"
104
109
112
OPERATING THE VALVE
4
1
Push CAP (1) over the O-RING SEAL (2).
TRIM INSTALLATION
1
3
7
5
8
6
If a temperature over 100˚F is desired, pull the RED STOP BUTTON (1) away from the body
of the MIXER UNIT and turn the TEMPERATURE KNOB.
If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed.
This will increase the mixed water temperature up to the maximum limit previously
selected in step 4.
Push ESCUTCHEON HOLDER (3) with lightly greased
O-RING SEAL (4) over CAP (1). Attach with the two
LONG SCREWS (7) provided.
Attach ESCUTCHEON (5) to ESCUTCHEON HOLDER (3)
with the two SHORT SCREWS (8) provided.
Align pins in back of DIAL PLATE (9) with holes in
ESCUTCHEON (5) and push DIAL PLATE (9) into place.
2
HANDLE INSTALLATION
Push TEMPERATURE-CONTROL KNOB (1) (with the red stop on top)
onto KNOB MOUNT (2).
Install HANDLE SCREW (3) and tighten with screwdriver.
Push KNOB CAP (4) into TEMPERATURE-CONTROL KNOB (1).
GREASE ESCUTCHEON
HOLDER O-RING SEAL
4
Should the hot and cold water supply pipes have been transposed making
adjustment impossible, proceed as follows:
TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION
3
Remove check stops and re-install them transposed.
Shut off water supply.
Remove handle and rim
CHECK STOP
(RED TO BLUE)
Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE
CHECK STOP is now on the left.
Turn the water supply back on and perform the temperature adjustment in step 4.
CHECK STOP
(BLUE TO RED)
T
O
P
/
O
B
E
N
2
2
M968682
MODEL NUMBERS
CHROME
BLACKENED BRONZE
POLISHED BRASS
SATIN NICKEL
002
068
099
295
Replace the "YYY" with
appropriate finish code
CENTRAL THERMOSTAT
LESS VOLUME CONTROL
TRIM KIT
A907143-YYY0A
HANDLE CAP
A918416-0070A
SCREW
A907080-YYY0A
DIAL PLATE
A918416-YYY0A
ESCUTCHEON SCREWS
A962628-YYY0A
TEMPERATURE
CONTROL HANDLE
A907655-YYY0A
ESCUTCHEON
A907655-YYY0A
ESCUTCHEON HOLDER SCREWS
A907090-YYY0A
CAP
A953962-YYY0A
ESCUTCHEON HOLDER
T
O
P
/
O
B
E
N
T203.730
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
  • Page 1 1
  • Page 2 2
  • Page 3 3

American Standard T203.730 User manual

American Standard
Brand
American Standard
Model
T203.730
Category
Sanitary ware
Type
User manual

American Standard T203.730 is a central thermostat without volume control. It has a maximum mixed water temperature of 109°F, which can be adjusted to 104°F or 112°F. The thermostat also features a red stop button that allows the user to increase the mixed water temperature up to the maximum limit. The thermostat comes with an escutcheon holder, escutcheon, dial plate, screw, cap, temperature control handle, and handle cap. To install the thermostat, the user will need a flat blade screwdriver and a Phillips screwdriver.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents