American Standard T420.732.224 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
American Standard T420.732.224 is a central thermostat, a device that controls the temperature of water in your home or office. With this device, you can limit the maximum mixed water temperature to 104°F or 112°F, for your safety and comfort. It is easy to install and comes with a variety of trim kits to match your bathroom décor. It is also easy to operate, with a simple turn of a knob to adjust the temperature.
American Standard T420.732.224 is a central thermostat, a device that controls the temperature of water in your home or office. With this device, you can limit the maximum mixed water temperature to 104°F or 112°F, for your safety and comfort. It is easy to install and comes with a variety of trim kits to match your bathroom décor. It is also easy to operate, with a simple turn of a knob to adjust the temperature.
- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
RECOMMENDED TOOLS
M965030 REV.1.6 (4/15)
ROUGHING-IN DIMENSIONS
CARE INSTRUCTIONS:
Certied to comply with ANSI A112.18.1M
ASSE 1016
To ensure that your installation proceeds smoothly, please read
these instructions carefully before you begin.
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
INSTALLATION
INSTRUCTIONS
T42073X Series
PORTSMOUTH
®
CENTRAL THERMOSTAT
LESS VOLUME CONTROL
TRIM KIT
H
O
T
C
O
L
D
Flat Blade Screwdriver
Phillips Screwdriver
242mm
(9-5/8")
151mm
(5-7/8")
86mm
(3-3/8")
25mm
(1")
34mm
(1-3/8")
193mm
(7-5/8")
LEVER
HANDLE
CROSS
HANDLE
150mm
(5-7/8")
48mm to 68mm
(2" to 2-5/8")
R510
1/2 NPT
R530
3/4 NPT
R510
1/2 NPT
R530
3/4 NPT
• To keep your new faucet looking new, please follow
these simple care instructions:
DO: • Simply rinse the faucet clean with clear water.
• Dry the faucet with a soft cotton cloth.
DO NOT:
• Do not use any abrasive cleaners, cloths, or
paper towels.
• Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
• Remove as much surface dirt and lm using clear
water and soft cotton cloth (as described above).
• Use any of the following to remove tough surface
lm and build-up:
• Mild liquid detergents
• Clear ammonia free liquid glass cleaners
• Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
• Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
Failure to follow these care instructions may damage
the Faucet’s finish.
- 2 -
1
4
ALIGNMENT
HOLES
2
3
5
6
H
O
T
C
O
L
D
• Install STEM ADAPTER (1) onto KNOB MOUNT (2) with
ADAPTER SCREW (3).
• Align HANDLE (4, 4a) and push onto KNOB MOUNT (2).
• Tighten SET SCREW with HEX WRENCH (5) supplied.
• Turn water supply on and test installed tting.
• If the system is delivering all Hot or all Cold and no mixed water, the pipes are probably transposed.
See step 3 for TRANSPOSED SUPPLY PIPING.
• Operate valve from cold to hot. Check temperature. If max mixed water
temperature is too hot or too cold see step 4 and re-calibrate the valve.
Should the hot and cold water supply pipes have been transposed making
adjustment impossible, proceed as follows:
• Shut off water supply
• Remove handle and rim
• Remove check stops and re-install them transposed
• Important Note: RED CHECK STOP is now on the right of the mixer body and
the BLUE CHECK STOP is now on the left.
• Turn the water supply back on and perform the temperature adjustment in step 4.
• Check that arrow marking B points vertically upwards. If not, push the BLACK
CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3)
and re-install KNOB MOUNT (3) with arrow “B” pointing upwards.
SET HOT LIMIT STOP
• The maximum mixed water temperature is set at 109˚F at the factory.
This setting can be changed if desired.
• Remove the TEMPERATURE LIMIT STOP (4) (H shaped Red Plastic part).
Re-install it at the desired notch as indicated in the diagram to limit the maximum
mixed water temperature to 104˚F or 112˚F.
• For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout
temperature is 100˚F. Check that arrow marking A on the KNOB MOUNT (3) still points
upward after adjusting the thermostat to 100˚F. If not, pull out the RED LOCKING DEVICE (5).
Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow.
• Re-install the KNOB MOUNT (3) so that the arrow marking A points upwards.
• Re-install RED LOCKING DEVICE (5).
HANDLE INSTALLATION
OPERATING THE VALVE
TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION
TEMPERATURE CALIBRATION
2
5
3
4
• Push CAP (1) over the O-RING SEAL (2).
• Push ESCUTCHEON (3) over CAP (1).
• Attach ESCUTCHEON (3) to VALVE (4) with the two
SCREWS (5) provided.
• Push DIAL PLATE (6) over CAP (1) and into the four
alignment holes in ESCUTCHEON (3).
TRIM INSTALLATION
1
M965030 REV.1.6 (4/15)
1
3
4
5
4a
2
C
H
O
T
C
O
L
D
CHECK STOP
(RED TO BLUE)
CHECK STOP
(BLUE TO RED)
1
3
5
2
4
ARROW
"A"
ARROW
"B"
104
109
112
COLD
HOT
C
H
O
T
C
O
L
D
- 3 -
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Replace the “YYY” with
appropriate finish code
CHROME 100
BLACKENED BRONZE 068
OIL RUBBED BRONZE 224
SATIN NICKEL 295
MODEL NUMBER
T420.73X Series
PORTSMOUTH
®
CENTRAL THERMOSTAT
LESS VOLUME
CONTROL TRIM KIT
M965030 REV.1.6 (4/15)
M962063-YYY0A
LEVER HANDLE KIT
M962003-YYY0A
DIAL PLATE
M962065-YYY0A
CROSS HANDLE KIT
M923045-0070A
HEX WRENCH
A918434-0070A
ESCUTCHEON SCREWS
M962629-YYY0A
ESCUTCHEON KIT
A907090-YYY0A
CAP
M918038-0070A
ADAPTER
M918990-0070A
SELF TAPPING SCREW
H
O
T
C
O
L
D
-
1
-
2
-
3
American Standard T420.732.224 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
American Standard T420.732.224 is a central thermostat, a device that controls the temperature of water in your home or office. With this device, you can limit the maximum mixed water temperature to 104°F or 112°F, for your safety and comfort. It is easy to install and comes with a variety of trim kits to match your bathroom décor. It is also easy to operate, with a simple turn of a knob to adjust the temperature.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard T064.730.002 Installation guide
-
-
-
-
-
American Standard Moments T506.730 User manual
-
-
-
-
