Digimerge DBD13 Quick start guide
- Category
- Security camera accessories
- Type
- Quick start guide
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
VISIT
www.digimerge.com
Copyright © 2010 Digimerge Technology Inc.
www.digimerge.com
Digimerge Technologies Inc.
Copyright © 2010 Digimerge Technologies Inc.
As our products are subject to continuous improvement,
Digimerge reserves the right to modify product design,
specifications and prices, without notice and without
incurring any obligation. E&OE
IT’S ALL ON THE WEB!
Camera Specifications
Dimensions:
Image Sensor High Resolution 1/4” Sensor
Lens / Lens Mount
Video Format / Pixels
Horizontal Resolution
Minimum Illumination
Termination
IR / Night Vision Range
FOV (diagonal)
S/N Ratio
Sync. & Scan. Systems
Video Output
Power Consumption
NTSC: 656(H) x 492 (V)
480 TVL
3.0 LUX
Video: BNC Female
Power: Barrel Female
N/A
73 Degrees
48dB
Internal; 2:1 Interlace
Comp. 1.0 Vpp @ 75ohm
100 mA max
Operating Temp.
Dimensions
LxWxH
(with dome)
14°F ~ 122°F
(-10°C ~ 50°C)
4.7” x 4.7” x 3.3”
118 mm x 118 mm x 83 mm
3.6 mm F2.0/ Fixed
Iris & Shutter Speed AES; 1/60 ~ 1/50,000 sec.
Power Requirement 12V DC
Weight (with stand) 0.50 lbs / 0.23 kg
HIGH RESOLUTION
3-AXIS COLOR DOME CAMERA
QUICK START GUIDE
English Version 1.0
DBD13MODEL:
7. Adjust the angle of the camera as needed. Tighten
the four screws to secure camera angle.
8. Replace the dome cover. Twist the dome cover so
that the top and bottom notches do not align. This
locks the dome cover in place.
Connecting The Camera
1. Use the BNC connector to connect camera to a
monitor, switch etc.
2. Connect a 12V DC power supply to the camera.
Setup Diagram
Contents Installing the camera
1 x Mini Color Dome
Camera
To adjust the camera angle:
1. Twist the body of the camera and the base of the
camera so that the top and bottom notch align.
2. Remove the dome cover.
3. Mark the three mounting holes from the camera
base onto the mounting surface.
4. OPTIONAL: Secure the drywall anchors into the
marked areas of the mounting surface.
5. Align the mounting holes and secure the camera in
place with the provided screws.
6. Using a Phillps screwdriver (not included), slightly
loosen the four screws on the support ring.
Top notch
Bottom notch
WARNING - A regulated, UL/CSA approved
12V DC power supply is required for use with
this camera. Use of a non-regulated, non-
conforming power supply can damage this
product and will void the warranty.
3 x Mounting Screws
Connecting the camera
Features:
• High Resolution Image Sensor—produces sharp
and clear video
• Fixed IR Fiter provides accurate color
reproduction
• 3.6 mm lens provides a wide viewing angle
• Industry standard BNC video connection
• Wall/ Ceiling mountable
ATTENTION - Test all connections and ensure the camera is
working correctly prior to permanent installation by
temporarily connecting the camera(s) and cable(s) to the
viewing/recording solution.
-
1
-
2
Digimerge DBD13 Quick start guide
- Category
- Security camera accessories
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Digimerge DNV14TL2 User manual
-
-
-
-
Digimerge DND13TL2 User manual
-
-
-
-
-