1
The SATELLITE connectors on the VXS10S/VXS10ST allow for the connection of satellite mid-high speakers to be used at the same
amplifier output. This gives the benefit of reducing the number of amplifier channels and takes advantage of the high pass filter built in to
the VXS10S/VXS10ST. The high-pass filter is optimized for use with the following recommended speakers.
• Surface mount speaker VXS5 / VXS5W
• Ceiling speaker VXC4 / VXC4W or VXC6 / VXC6W
*VXS5 is used for illustrations/explanations in this guide.
Basic system for stereo playback
Stereo playback with wider coverage
About satellite connection
Recommended satellite speakers
Connection examples
VXS10S + two VXS5 (stereo system)
VXS10S + four VXS5 (stereo system)
VXS10S is a dual voice coil
subwoofer. Audio signal of
CH1+CH2 comes out from
VXS10S subwoofer.
Amplifier
Rear panel of VXS10S
Amplifier
VXS10S is a dual voice coil
subwoofer. Audio signal of
CH1+CH2 comes out from
VXS10S subwoofer.
English
Speaker system satellite guide
2
Here is an alternative system. Note that in this system, as one rather than both voice coils is driven, some specifications, such as the
maximum sound pressure level will differ from the product specification sheet.
Here is an example of a high impedance system comprising a VXS10ST subwoofer and two monaural satellites, driven from a single
amplifier channel. This can be further expanded with a second identical system, linked together using the Thru connector on the first
VXS10ST. Multi satellite systems can be structured using a single amplifier channel.
All satellite speakers must be set to 8 ohms (not 100V/70V taps) when connected to the satellite outputs of the VXS10S/VXS10ST.
■ VXS10S
Connect so that the total combined impedance of the satellite speakers is 4 ohms or above per ST1 / ST2 connector.
■ VXS10ST
Connect so that the total combined impedance of the satellite speakers is 8 ohms or above per ST1 / ST2 connector.
VXS10S + two VXS5 (monaural system)
VXS10ST + two VXS5 (monaural system)
Notes on connecting satellite speakers
Examples of total combined impedance
Amplifier
Basic system
Amplifier
Rear panel of VXS10ST
Impedance: 4Ω Impedance: 8Ω
: Speaker
-
1
-
2
Yamaha VXS10S/VXS10ST User guide
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Yamaha VXS10S/VXS10ST Guida utente
- français: Yamaha VXS10S/VXS10ST Mode d'emploi
- español: Yamaha VXS10S/VXS10ST Guía del usuario
- Deutsch: Yamaha VXS10S/VXS10ST Benutzerhandbuch
- русский: Yamaha VXS10S/VXS10ST Руководство пользователя
- Nederlands: Yamaha VXS10S/VXS10ST Gebruikershandleiding
- português: Yamaha VXS10S/VXS10ST Guia de usuario
- dansk: Yamaha VXS10S/VXS10ST Brugervejledning
- polski: Yamaha VXS10S/VXS10ST instrukcja
- čeština: Yamaha VXS10S/VXS10ST Uživatelská příručka
- Türkçe: Yamaha VXS10S/VXS10ST Kullanici rehberi
- svenska: Yamaha VXS10S/VXS10ST Användarguide
- suomi: Yamaha VXS10S/VXS10ST Käyttöohjeet
- română: Yamaha VXS10S/VXS10ST Manualul utilizatorului