Extron DTP HD DA 4K 330 User manual
- Category
- Video line amplifiers
- Type
- User manual
This manual is also suitable for
Extron DTP HD DA 4K 330 is a high-performance distribution amplifier that distributes one HDMI input signal to four simultaneous outputs via shielded twisted pair (STP) cables. It supports resolutions up to 4K @ 30 Hz and can transmit signals up to 330 feet (100 meters). The DTP HD DA 4K 330 is ideal for use in a variety of applications, including digital signage, video conferencing, and home theater systems. It features HDCP compliance, EDID Minder, and audio breakaway, making it a versatile and reliable solution for any AV installation.
Extron DTP HD DA 4K 330 is a high-performance distribution amplifier that distributes one HDMI input signal to four simultaneous outputs via shielded twisted pair (STP) cables. It supports resolutions up to 4K @ 30 Hz and can transmit signals up to 330 feet (100 meters). The DTP HD DA 4K 330 is ideal for use in a variety of applications, including digital signage, video conferencing, and home theater systems. It features HDCP compliance, EDID Minder, and audio breakaway, making it a versatile and reliable solution for any AV installation.
1
DTP HD DA4/DA8 4K 230/330 • Setup Guide
Overview
These Extron distribution ampliers distribute one HDMIinput signal to four (DTP HD DA4 4K models) or eight (DTP HD DA8 4K
models) simultaneous outputs via shielded twisted pair (STP) cables. The ampliers distribute the signal over a distance of up
to 230 feet (70 meters) or 330 feet (100meters) for resolutions up to 1080p @ 60 Hz, and 130 feet (40 meters) or 330 feet (100
meters) for resolutions up to 4K @ 30 Hz, depending on the model. This setup guide provides basic instructions for installation by
an experienced installer. For complete instructions, see the DTP HD DA4/DA8 4K 230/330 user guide on the Extron web site
(www.extron.com).
Typical DTP HD DA4/DA8 4K Application Examples
100-240V ~ 1.0A MAX
50/60 Hz
DTP HD DA4 330
LAN
3
4
1
2
OUTPUTS
INPUT
HDMI
LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
DTP
HDBT
AUDIO
SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
HDMI HDMI3
HDMI4
21 CONFIGURABLE
100-240V ~ --A MAX
50-60 Hz
AUDIOOUTPUT
TALLY OUT
CONTACT IN
L
12
R
L R
Tx Rx G
3214+V
1234G
RS-232
OUT
IN
HDMI
INPUT REMOTE
POWER
12V
0.3A MAX
IPL PRO S3
G
Tx Rx RTSCTS
G
Tx Rx RTSCTS
G
Tx Rx RTSCTS
COM 1 COM 2 COM 3
LAN / PoE
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
iPad
LAPTOP
PC
DVD
DOC CAM
AUXILIARY
DISPLAY ON
DISPLAY OFF
MUTE
VOLUME
VOLUME
VideoMore
DVD
Combined
RS-232
Displays with Speakers
HDMI
CATx Cable
up to 330' (100 m)
CATx Cable
up to 330' (100 m)
RS-232HDMI RS-232HDMI RS-2
32
HDMI
Extron
DTP HDMI
330 D Rx
Receiver
Extron
DTP HDMI
330 D Rx
Receiver
VGA
Laptop Laptop Laptop
Tablet
AudioHDMIHDMIHDMI
HDMI
RS-232
Ethernet Ethernet
Ethernet
TCP/IP
Network
Extron
TLP Pro 320C
3.5" Cable Cubby
TouchLink Pro
Touchpanel
Extron
IN1604 HD
Four Input
Scaler
Extron
IPL Pro S3
IP Link Pro
Control
Processor
Extron
DTP HD DA4 4K 330
DTP Distribution Amplier
100-240V ~ 1.0A MAX
DTP HD DA8 230
LAN
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
3
4
5
6
7
8
1
2
DTP
HDBT
OUTPUTS
INPUT
HDMI
LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
DTP
HDBT
AUDIO
SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK
OUTPUTS
AUDIO
TxRx GTxRx
RS-232IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232IR
OVER DTP
HDMI HDMI3
HDMI4
21 CONFIGURABLE
100-240V ~ --A MAX
50-60 Hz
AUDIOOUTPUT
TALLY OUT
CONTACT IN
L
12
R
L R
Tx Rx G
3214+V
1234G
RS-232
OUT
IN
HDMI
INPUT REMOTE
POWER
12V
0.3A MAX
IPL PRO S3
G
Tx Rx RTSCTS
G
Tx Rx RTSCTS
G
Tx Rx RTSCTS
COM 1 COM 2 COM 3
LAN / PoE
50/60 Hz
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
iPad
LAPTOP
PC
DVD
DOC CAM
AUXILIARY
DISPLAY ON
DISPLAY OFF
MUTE
VOLUME
VOLUME
VideoMore
DVD
Combined
RS-232
Displays with
Speakers
HDMI
CATx Cable
up to 330' (100 m)
CATx Cable
up to 330' (100 m)
Ext
ron
DT
P HDMI
33
0 D Rx
Re
ceiver
RS-232HDMI
Extron
DTP HDMI
330 D Rx
Receiver
VGA
Laptop Laptop Laptop
Tablet
AudioHDMIHDMIHDMI
HDMI
RS-232
Ethernet
Ethernet
Ethernet
TCP/IP
Network
Extron
TLP Pro 320C
3.5" Cable Cubby
TouchLink Pro
Touchpanel
Extron
IN1604 HD
Four Input
Scaler
Extron
IPL Pro S3
IP Link Pro Control
Processor
Extron
DTP HD DA8 4K 330
DTP Distribution
Amplier
Front Panel
CONFIG
DTP HD DA4
INPUT
OUTPUTS
SIGNAL
HDCP
DTP DISTRIBUTION AMPLIFIER
LOOP
THRU
34
1
2
CONFIG
DTP HD DA8
INPUT
OUTPUTS
SIGNAL
HDCP
DTP DISTRIBUTION AMPLIFIER
LOOP
THRU
34
5
6
7
8
1
2
A BF
E
D
C
A BF
E
D
C
A Power status LED — Lights green when power is
applied to the unit.
B USB Config port — Used for rmware updates,
SIS conguration, and software control.
C Input Signal LED — Lights green indicating a
signal is detected on the HDMI input.
D Input HDCP LED — Lights green indicating
HDCP presence is detected on the HDMI input.
E Output Signal LEDs — Light green indicating a
signal is detected on the HDMI outputs.
F Output HDCP LEDs — Light green indicating
HDCP presence is detected on the HDMI outputs.
2
DTP HD DA4/8 4K 230/330 • Setup Guide (Continued)
Rear Panel
50/60Hz
100-240V 1.0A
DTP HD DA4 330
LAN
3
4
1
2
DTP
HDBT
OUTPUTS
INPUT
HDMI
LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
AUDIO
50/60Hz
100-240V 1.0A
DTP HD DA8 330
LAN
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
3
4
5
6
7
8
1
2
DTP
HDBT
OUT
SIG LINK
DTP
HDBT
OUTPUTS
INPUT
HDMI
LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
AUDIO
B
A C I
B D E F G H J K
A C I
B D E F G H J K
A Power input — Connect the provided IEC connector to a 100-240 VAC (50 or 60 Hz) power source.
B Analog audio input — Connect an unbalanced stereo audio source to these 3.5 mm mini stereo jacks.
NOTE: The units do NOT embed analog audio onto the HDMI signal. This analog audio signal is transmitted
simultaneously with audio embedded within the HDMI signal.
C Analog audio Loop Thru — Connect an audio system to this 3.5 mm mini stereo jack for local loop-through monitoring
of the source audio.
D HDMI input — Connect a source device to this female HDMI type A connector.
E HDMI Loop Thru — Connect a display to this female HDMI type A connector for local loop-through monitoring of the
source signal.
F DTP/HDBaseT configuration switch — Set this 2-position, recessed switch to congure the output between HDBaseT
and DTP modes. When congured for HDBaseT, use an HDBaseT-compatible receiver. When congured for DTP, use a
DTP-compatible receiver.
G DTP/HDBaseT outputs — Use shielded twisted pair (STP) cables to connect these 4 (DA4 models) or 8 (DA8 models)
outputs to the inputs of a compatible receiver.
ATTENTION:
• Do not connect these outputs to a telecommunications or computer data network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
H Over TP RS-232/IR connectors — Use these 4 (DA4 series) or 8 (DA8 series) 3.5 mm, 5-pole captive screw connectors
to pass bidirectional RS-232 and IR control between compatible devices.
I Reset button and LED — Press and hold the reset button for approximately 6 seconds to restore the unit to factory
default settings. The reset LED will ash green, indicating that the default settings have been restored.
J LAN connector — Use an RJ-45 cable to connect this jack to a LAN for Ethernet control of the device.
K Remote RS-232 connector — Connect an RS-232 device to this 3-pole, 3.5 mm captive screw connector to control the
DTP HD unit. Congure it as follows: 9600 baud rate, 8 data bits, 1 stop bit, no parity. See Installation on the next page
for wiring instructions.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. www.extron.com
3
68-2545-50 Rev. A
01 15
DTP HD DA4/DA8 4K 230/330 • Setup Guide (Continued)
Installation
1. Mount the HDMI DA unit in a suitable location (see the Mounting section of the DTP HD DA4/DA8 4K 230/330 user guide for
mounting options). Follow the instructions provided with the mounting kit.
2. Connect the USB or RS-232 connector (see the gure below) to a PC for conguration and maintenance. Use SIS commands
or the Extron PCS program to congure EDID Minder, mute the video signal, mute the audio signal, adjust the video color
bit depth, or monitor the signal and HDCP status, as required (see the DTP HD DA4/DA8 4K 230/330 user guide for more
information).
RS-232
Tx Rx G
REMOTE
TransmitReceive
ReceiveTransmit
GroundGround
DB9 Pin Locations
Female
51
96
Pin 2 = Rx
Pin 3 = Tx
Pin 5 = G
Computer DTP HD DA4/DA8
3. Connect the rear panel transmitter outputs (
G
) to the rear panel receiver inputs using shielded twisted pair (STP) cable.
NOTE: The DTP HD DA4/DA8 4K 230 and 330 products can transmit video, control, and audio (if applicable) signals up
to 230 feet (70 meters) and 330 feet (100 meters), respectively.
For optimal performance, Extron highly recommends the following:
z RJ-45 termination with STP cable must comply with TIA/EIA-T568B wiring standard for all connections. For more
information on cable wiring and termination, see the full product user guide at www.extron.com.
z Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable bandwidth of 400 MHz.
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201.
z Use shielded RJ-45 plugs to terminate the cable.
z Limit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches
used. If possible, limit the number of patches to only 1 or 2 total.
z If RJ-45 patches must be used in the system, Extron recommends shielded CAT 6 (or better) patches.
4. Connect display devices to the transmitter and receivers.
NOTE: Use the LockIt HDMI cable lacing brackets provided to secure the HDMI connectors (see the LockItHDMICable
Lacing Bracket installation guide).
a. Connect and power on the display devices to the outputs on the compatible receivers.
b. (Optional) Connect and power on a local display device to the Loop-Thru connector (
E
).
5. Connect to a 110-240 VAC (50 or 60 Hz) power supply using the provided IEC power cord.
6. Connect and power on the source device.
-
1
-
2
-
3
Extron DTP HD DA 4K 330 User manual
- Category
- Video line amplifiers
- Type
- User manual
- This manual is also suitable for
Extron DTP HD DA 4K 330 is a high-performance distribution amplifier that distributes one HDMI input signal to four simultaneous outputs via shielded twisted pair (STP) cables. It supports resolutions up to 4K @ 30 Hz and can transmit signals up to 330 feet (100 meters). The DTP HD DA 4K 330 is ideal for use in a variety of applications, including digital signage, video conferencing, and home theater systems. It features HDCP compliance, EDID Minder, and audio breakaway, making it a versatile and reliable solution for any AV installation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron DTP HD DA 4K 230 User manual
-
Extron electronics HDMI 230 D User manual
-
Extron DTP HDMI 4K 330 Rx User manual
-
-
Extron electronics DTP T/R DP 330 User manual
-
-
Extron IPL T PCS4i Owner's manual
-
Extron DTP HDMI 4K 230 D Tx User manual
-
-
Extron electronics DTP DVI 230 D User manual
Other documents
-
Extron electronics DTP HD DA8 4K 330 User manual
-
Extron electronic DTP T USW 233 User manual
-
-
Extron electronics DTP T SW4 HD 4K User manual
-
-
Extron electronics DTP T MK 332 User manual
-
Extron electronics HDMI DA2 User manual
-
Abtus HDBT-GAHD31T/AP3 User's Operation Manual
-
C2G 30012 Owner's manual
-
Extron electronics TLP 350MV User manual
