Halsey Taylor HACVRBL.A Owner's manual

Brand: Halsey Taylor

Model: HACVRBL.A

Category: Flat panel wall mounts

Type: Owner's manual

Page 1

HAC8VRBLQ*1A

97771C (Rev. L - 11/04)

USES HFC-134A REFRIGERANT

HALSEY TAYLOR OWNERS MANUAL

20, 21, 22,

24,25

See Fig. 3 (Page 3) For

Push Button Mechanism

47, 10

See Fig. 5

36, 37, 38

40, 41, 54

11, 44, 45,

46, 58

12, 13, 18

FIG. 1

Page is loading ...

Page 3

HAC8VRBLQ*1A

97771C (Rev. L - 11/04)

COOLER BACK

SUPPORT DE SUSPENSION

ARRIÈRE DU REFROIDISSEUR

HANGER BRACKET

FIJADOR DE SUSPENSIÓN

SUPPORT DE SUSPENSION

PUSH BAR MECHANISM

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON

HANGER BRACKETS & TRAP

INSTALLATION

1) Remove hanger bracket fastened to back of cooler by

removing one (1) screw.

2) Mount the hanger bracket and trap as shown in Figure 2.

NOTE: Hanger Bracket MUST be supported securely. Add

fixture support carrier if wall will not provide adequate

support.

IMPORTANT:

y 7 in. (178mm) dimension from wall to centerline of trap must

be maintained for proper fit.

y Anchor hanger securely to wall using all six (6) 1/4 in. dia.

mounting holes.

3) Install straight valve for 3/8" O.D. tube.

INSTALLATION OF COOLER

4) Hang the cooler on the hanger bracket. Be certain the

hanger bracket is engaged properly in the slots on the cooler

back as shown in Fig. 4.

5) Loosen the two (2) screws holding the lower front panel at

the bottom of cooler base and two (2) screws at the top.

Remove the front panel and set aside.

6) Connect water inlet line--See Note 4 of General Instructions.

7) Remove the slip nut and gasket from the trap and install

them on the cooler waste line making sure that the end of

the waste line fits into the trap. Assemble the slip nut and

gasket to the trap and tighten securely.

START UP

Also See General Instructions

8) Stream height is factory set at 45-50 PSI. If supply

pressure varies greatly from this, adjust the screw on

regulator item 16 by using a small screwdriver through the

small hole in the push button item 2 (See Fig.3). CW

adjustment will raise stream and CCW adjustment will lower

stream. For best adjustment, stream should hit basin

approximately 6-1/2" (165mm) from bubbler.

FIG. 3

FIG. 4

CAUTION: Cleaning of Bronzetone Models requires special

care. Outer surfaces must be cleaned with a mild detergent or

mixture of vinegar and water only, rinsed and wiped dry.

Abrasive and Acidic cleaners may eventually damage the

Bronzetone finish.

WATER FLOW DIRECTION

Page 4

HAC8VRBLQ*1A

97771C (Rev. L - 11/04)

*REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL

ASSEMBLY.

NOTE: All correspondence pertaining to any of the above

water coolers or orders for repair parts MUST include Model

No. and Serial No. of cooler, name and

part number of replacement part.

PRINTED IN U.S.A.

2222 CAMDEN COURT

OAK BROOK, IL 60523

630.574.3500

ITEMIZED PARTS LIST

Item

No.

Part

No.

22822C

22814C

27295C

22862C

26776C

22854C

26800C

22955C

Panel Color

Stainless Steel

COLOR TABLE

PART NO

22897C

45662C

75672C

45663C

See Color Tbl

26999C

56033C

75570C

75589C

160270508640

600985451640

40045C

15005C

61313C

50986C

110868642550

31517C

30664C

70018C

31490C

70009C

22899C

38417001

75524C

55996C

98118C

62152C

66703C

See Color Tbl

101516143550

100806740570

19037000

36094C

35959C

35768C

66532C

45351C

100147140560

56121C

75588C

28462C

100322740560

40022C

31513C

66534C

70002C

55931C

36158C

15009C

56092C

70682C

45485C

75661C

400660943730

75583C

75523C

75520C

75674C

Panel - Bottom Dispenser

Button - Push

Screw - Cap

Sleeve - Push Button

Panel - Right Side

Panel - Left Side

Panel - Front Push

Cover - Bottom

Washer

Screw - Torx

Gasket

Strainer - Bright

Plug - Drain 1-1/2CP

Hex Nut

Retaining - Nut

Regulator

Holder - Regulator

Screw

Power Cord

Fan Blade

Hex Nut - Fan Blade

Fan Motor

Screw - (Fan Motor)

Shroud - Fan

Screw - #8-18 x 3/8” Lg. (Fan Shroud)

Clip (Front and Rear Panels)

Strainer (See "General Instructions")

Bubbler Assembly

Condenser

Drier

Panel - Right Rear (Refrig. Unit)

Panel - Right Rear (Left Unit)

Panel - Left Rear (Left Unit)

Panel - Left Rear (Refrig. Unit)

Panel - Front Lower

Stud - Compressor Mtg.

Grommet - Compressor Mtg.

Clip - Compressor Mtg.

Compressor Serv. Pak EMI 70 HNR

Relay

Cover - Relay

Heat Exchanger

Wasteline Assy.

Gasket - Drain

Fitting - Elbow

Nut - Slip Joint 1-1/4

Basin - Stainless Steel

Washer

Wasteline Assy.

Cold Control

Evaporator Assembly

Screw - #10 x 1/2" Lg. HHSM

Cover-Dispenser Bottom Gray

Overload

Bubbler - Nipple

Tubing - Poly (Cut To Length)

Fitting - Tee 1/4

Tailpiece Assembly

Screw - Torx

Hanger Bracket (Not Shown)

Fitting - Elbow 5/16" - 1/4" (Not Shown)

Bit - Pinned Torx

Wrench - Allen 7/64

ITEM

DESCRIPTION

*39

FIG. 5

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

Halsey Taylor HACVRBL.A Owner's manual

Brand: Halsey Taylor

Model: HACVRBL.A

Category: Flat panel wall mounts

Type: Owner's manual

Download PDF

report

Halsey Taylor HACVRBL.A Owner's manual

Halsey Taylor HACVRBL.A Owner's manual

Related papers

Other documents