Quirky iso User manual

Brand: Quirky

Model: iso

Type: User manual

humidity-sensing exhaust fan

and motion-activated night light

ventilateur aspirant activé par la vapeur

et veilleuse activée par le mouvement

extractor extractor activado por vapor

y luz nocturna activada por movimiento

ISO

For service questions, contact Quirky at 1-866-578-4759.

For sales inquiries, contact Sylvane at 1-800-934-9194.

ISO|

ISO|

TABLEOFCONTENTS

FEATURESANDSPECIFICATIONS

INTHEBOX

SAFETYINFORMATION

PREPARATION

WIRINGINSTRUCTIONS

INSTALLATIONINSTRUCTIONS

NEWCONSTRUCTION

EXISTINGCONSTRUCTION

WALLSWITCHSPECIFICATIONS

CAREANDMAINTENANCE

TROUBLESHOOTING

WARRANTY

ULWARNINGSTATEMENT























ENGLISH

ISO|

FEATURESANDSPECIFICATIONS

FEATURES

• Humidity-sensingfanshutsoﬀaerbathroomissteam-free

• Motion-activatednightlightfunctionsindarkenvironments

andshutsoﬀtwominutesaermotionceases

• Fanisultra-quiet

• Brightﬂuorescentlightforgeneralbathroomillumination

TYPICALINSTALLATION

FAN HOUSING

ROOF

DUCT

EXTERIOR WALL

SPECIFICATIONS

• Grilldimensions”x”x”cmxcmxcm

• Housingdimensions/”x⁄”x”

cmxcmxcm

• Ductdiameter”cm

• Soundoutputsones

• AirﬂowCFM

• ExhaustfanspeedRPM

• Weightlbskg

• ElectricalratingV/Hz/A/Wfanonly

V/Hz/A/Wfanandlights

• Assembledweightlbskg

RequirestwoWWequivalentGUbase

CFLbulbsandoneWCintermediatebase

incandescentbulbnotincluded

Make sure the vent/duct is venting outward

and not up into the ceiling.

ISO|

fanbodywithreﬂector

suspensionbracketI

longwoodscrew

actualsize

shortmachinescrew

actualsize

longmachinescrew

actualsize

switch

suspensionbracketII suspensionbracketIII

metalrimandglass

bell

ceilingplate

INTHEBOX

NOT INCLUDED: Tools required for assembly and lightbulbs.

ISO|

SAFETYINFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand the entire manual before attempting

to assemble, operate, or install the product.

• Alwaysdisconnectthepowersupplypriortoservicingthefan

motororjunctionbox

• Installationworkmustbecarriedoutbyaqualiﬁedpersonsin

accordancetoalllocalandsafetycodesincludingtherulesfor

ﬁre-ratedconstruction

• Followalllocalbuildingsafetyandelectricalcodesaswell

asNECNationalElectricalCodeandOSHAOccupational

SafetyandHealthAct

• ElectricServicesupplymustbevoltshertz

• Thisunitmustbeproperlygrounded

• Donotbendorkinkthepowerwires

• Exercisecaretonotdamageexistingwiringwhencutting

ordrillingintowallsorceilings

• Suﬃcientairsupplyisrequiredforpropercombustion

andexhaustionofgasesthroughthechimneyﬂue

orfuelburningequipmenttopreventback-draing

*SeethestandardsofNFPANationalFireProtection

AssociationandASHRAEAmericanSocietyfor

HeatingRefrigerationandAirConditioningEngineers

andthelocalbuildingcodeauthorities

• WARNING–Toreducetheriskofﬁreorelectricshock–do

notusethisfanwithanysolidstatecontroldevicesuchasa

remotecontroldimmerswitchorcertaintimersMechanical

timersarenotsolidstatedevices

• Donotinstallinacookingarea

• CAUTION–Forgeneralventilatinguseonly–donotuseto

exhausthazardousorexplosivevapors

• Fansshouldalwaysbeventedtotheexteriorincompliance

withlocalcodes

• DonotinstallinaceilingwithinsulationgreaterthanR

• Ductworkshouldbeinstalledinastraightline

withminimalbends

• Ductworksizemustbethesamesizeasthedischarge

andshouldnotbereducedReducingtheductsizemay

increasefannoise

• Priortoservicingorcleaningthisunitshutoﬀpowersupply

atthepanelandlocktopreventthepowerfrombeingturned

onIfthepanelcannotbelockedclearlymarkthepanelwitha

warningtagtopreventthepowerfrombeingturnedon

• Usethisunitinthemannerintendedbythemanufacturer

• WARNING–TOREDUCETHERISKOFFIREELECTRIC

SHOCKORINJURYTOPERSONSOBSERVETHE

FOLLOWING

aUsethisunitonlyinthemannerintendedbythemanufacturer

Ifyouhavequestionscontactthemanufacturer

bBeforeservicingorcleaningunitswitchpoweroﬀatservice

panelandlocktheservicedisconnectingmeanstoprevent

powerfrombeingswitchedonaccidentallyWhentheservice

disconnectingmeanscannotbelockedsecurelyfastena

prominentwarningdevicesuchasatagtotheservicepanel

• Ifyouhaveanyquestionspleasecallcustomerserviceat

QUIRKY

ISO|

PREPARATION

Before beginning assembly of product, make sure all parts are

present. Compare parts with package contents list and hardware

contents lists. If any part is missing or damaged, do not attempt

to assemble the product.

Estimated assembly time: one hour.

Tools required for assembly (not included): drywall saw, ”

Phillips head drill bit, electric drill, stud ﬁnder,  drive Phillips

head screwdriver, standard face plate for light switch.

WARNING: Turn oﬀ electricity at breaker box before

beginning installation.

• Carefullyremoveunitfromcarton

• Checkareaaboveinstallationlocationtobesurethatwiring

canruntotheplannedlocationductworkcanberunand

theareaissuﬃcientforproperventilationIfductcannot

berunawayfromceilingorthereisnoductconsultwitha

professionalbeforeinstalling

• Inspectductworkandwiringbeforeproceedingwithinstallation

• Beforeinstallationmakesurethereisanaccessibleareafor

futuremaintenanceaccess

• Youmayneedthehelpofasecondpersontoinstallthisfan

onepersonontheatticsideandtheoneonthebathroomside

Note: Installation may vary depending on how the previous bath

fan was installed. Supplies necessary for the installation of your

bath fan are not all included; however, most should be available

at your local home improvement or hardware store.

The hole for installation is not sized to the fan unit – use the

following dimensions so that the Iso ceiling panel will rest ﬂush

against the ceiling.

DIMENSIONREQUIREMENTS

Ceiling Opening

(L)

Ceiling Opening

(W)

Ceiling Opening

(H)

incm incm incm

FANWIRINGDIAGRAM

WIRINGINSTRUCTIONS

LIGHT HOUSING

FAN HOUSING CONTROLLER

PCBA

UPTOWATTS

AUTOMATICTERMINALSWITCH

MOTOR

GREENWIRETOGROUND

CAPACITOR

FORLONG

LIFEOFFAN

WHITEWIRETONEUTRAL

BLACKWIRETOLIVE

WARNING: Wiring must comply with applicable electrical codes.

Turn OFF power before removing or installing wire nuts.

WARNING: Copper to copper only. Do not use aluminium wire.

CAUTION: Accessory part (wires nuts) should meet installation

instructions below.

NOTE: The wire nut is reusable on solid wire of the same wire

gage or smaller, do not reuse the wire nut on stranded wires.

• Stripwires/˝–/˝cmcm

• Takebothwires

fromwallandfromnewswitch

andtwisttogethersecurely

Insertsecuredwiresintowirenut

• Verifywiresarefullyinserted

intothewirenut

Further wiring instructions are included

in the Installation Instructions section

NOTE – Important wire information: Maximum temperature

rating FCvolts maximum for building wire and

 volts maximum for building wire and  volts maximum

in signs and lighting ﬁxtures.

The acceptable wire range includes: Solid:  AWG

WIRE NUT

PRODUCT

WIRES

HOUSE

WIRES

BLACK WIRE

TO LIVE

WHITE WIRE

TO NEUTRAL

GREEN WIRE

TO GROUND

ISO|

 Using a drywall saw, cut a ”x”cmxcm

opening in the ceiling for the panel.

a) Make sure the hole you cut is between two () studs –

this can be done using a stud ﬁnder.

INSTALLATIONINSTRUCTIONS

BEFOREINSTALLATION

Turn oﬀ power source. Review all safety precautions.

PLEASE NOTE:

• IfinstallingIsoinalocationthatcanbeaccessedfromabove

theinstallationlocationviaatticorcrawlspacefollowthe

“NewConstruction”instructions

• IfinstallingIsoinalocationthatCANNOTbeaccessed

fromabovetheinstallationlocation–followthe“Existing

Construction”instructions

It is required to have an exhaust duct that leads outside and not

into the ceiling or attic as this could cause water damage.

The ventilation fan is UL approved for use over a bathtub or

shower when installed in a GFCI protected circuit. Do not use

fans over a bathtub or shower that are not approved for that

application and marked accordingly.

PLEASE NOTE: the fan is to be installed at least  feet

 meters) above ﬂoor level.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Installationworkandelectricalwiringmustbedonebyqualiﬁed

personsinaccordancewithallapplicablecodesandstandards

includingﬁre-ratedconstruction

• Suﬃcientairisneededforpropercombustionandexhausting

ofgasesthroughtheﬂuechimneyoffuelburningequipment

topreventbackdraingFollowtheheatingequipment

manufacturer’sguidelineandsafetystandardssuchasthose

publishedbytheNationalFireProtectionAssociationNFPA

andtheAmericanSocietyforHeatingRefrigerationandAir

ConditioningEngineersASHRAEandthelocalcodeauthorities

• Whencuttingordrillingintowallorceilingdonotdamage

electricalwiringandotherhiddenutilities

• Ductedfansmustalwaysbeventedtotheoutdoors

• Ifthisunitistobeinstalledoveratuborshoweritmustbemarked

asappropriatefortheapplicationandbeconnectedtoaGFCI

GroundFaultCircuitInterrupter–protectedbranchcircuit

 Insert the suspension brackets into the fan body – there are

suspension brackets provided:

• SuspensionbracketIattachestotherailontheside

oftheunit

• SuspensionbracketIIwillslideintosuspensionbracketI

Makesuretheyslidefreelywithnoobstruction

• SuspensionbracketIIIattachestotheothersideoftheunit

wheretheexhaustportis

NOTE: If the ceiling joists are less than ” (cmapart,

the suspension brackets need to be shortened with a dremel

or angle grinder before inserting into unit.

NEWCONSTRUCTION

ISO|

 Insert the fan body into the ceiling cut out making sure to align

the duct connector with the fan body.

IMPORTANT: The bottom edge of the fan body MUST BE /”

 cm) ABOVE THE CEILING (it should not hang down or be

level with the ceiling).

NOTE: Duct/outlet adapter can be removed for easier

installation through the ceiling opening.

 To mount the fan body to ceiling joists – screw in the long

wood screws (six in total) into the suspension brackets

connected to the joist.

Hardware used: Long wood screw x

CAUTION: Dimension “B” should allow for thickness of ceiling

board used in your application. Do not ﬂush mount to joist.

FAN BODY

FAN

JOIST

0.7” CEILING

BOARD

DIMENSION B

CEILING

BOARD

CEILING BOARD

JOIST

BRACKET

 Using wire nuts (provided), connect house wires to ventilating

fan wires: black to black; white to white; green to green;

(refer to wiring diagram on page ).

CAUTION: If your house wires do not match these colors,

you must determine what each house wire represents

before connecting and you may need to consult an electrical

contractor to determine this safely.

 Attach the ceiling panel (contains the infrared motion sensor,

light sensor, and humidity sensor):

• Pinchﬁrstmountingspringonpanelandinsertintonarrow

rectangularslotsinsidethefanhousingnexttothefanmotor

 Connect the ”cm duct to vent duct (in ceiling)

and secure it with duct tape or clamps (not included).

Finish ceiling work.

 Connect the main PCB via the plastic connector on the end

of rainbow ﬂat cable to the PCB board on the ceiling panel.

WIRE NUT

PRODUCT

WIRES

HOUSE

WIRES

ISO|

 Pinch second mounting spring and give the ceiling panel

aslight push to click into place. Ceiling panel should be

mounted ﬂush against the ceiling.

 Push bell into center of ceiling panel to install. Give it a slight

tug to make sure it does not pop oﬀ. It should be able to

rotatefreely.

 Carefully install two WWequivalent) GUCFL

bulbs (not included) into the sockets and one (WC

incandescent bulb (not included) into the black center socket.

 Remove existing fan and fan housing.

EXISTINGCONSTRUCTION

 Make sure the existing hole is at least ”x”

cmxcmbut smaller than ”x”cmxcm

 Cut into the ceiling (about ”cm] wide to ﬁt drill bit – refer

to diagram) to extend suspension brackets and mount to stud

(use a stud ﬁnder if necessary).

NOTE: Save drywall piece to patch holes cut for suspension

brackets aer completing step in New Construction.

 Refer to Steps  in “New Construction” to

completeinstallation.

 Attach metal trim glass dish to bell with the four () short

machine screws (provided).

Hardware used: Short machine screws x 

 Turn on electricity at breaker box aer completing installation.

HOLE FOR FAN

JOIST

”

”

ISO|

WALLSWITCHSPECIFICATIONS

The wall switch has two sliding switches: one for the fan and

one for the night light. There is also a button for the main lights.

The fan and night light sliding switches have three positions:

oﬀ/auto/on. In “auto” mode, the fan turns on when the humidity

sensor senses suﬃcient humidity, and the nightlight turns on

when the motion detector detects motion in a dark environment.

The humidity and motion detectors are built into the ceiling

component. In “on” mode, the fan and nightlight remain on even

if the room is not humid and no motion is detected. The main light

button clicks on and oﬀ; it has no “auto” mode.

Switch (Fan) ON/OFF/AUTO

Switch (Night Light) ON/OFF/AUTO

Button (Main light) ON/OFF

TOINSTALLTHEWALLSWITCH

 Turn oﬀ the power to the switch at the main circuit breaker

orfuse panel.

 Unscrew and remove the switch plate; then use a voltage

tester to make sure that the circuit is dead.

 Unscrew the switch from the electrical box and pull it out

with the wires still attached.

• Twoorthreewireswillbeattachedtotheswitch

–anincominghotwirewhichisblack

–aneutralwirewhichiswhite

– andpotentiallyagroundingwirewhichisgreen

orbarecopper

• Theremaybeotherwiresintheswitchboxbutyouareonly

dealingwiththeonesconnecteddirectlytotheswitch

• Youmayﬁndawhitewirethathasblacktapeonitconnectedto

theswitchThistapeindicatesthatthewhitewireisbeingused

asablackorcoloredwireintheswitchlegsoitisnotneutral

 Compare your new switch with the one you’re replacing

to ﬁnd the corresponding locations for the wires.

 To connect wires to the new switch:

• Locatetheblackhotwireinyourswitchboxandattachtothe

blackwireinthenewswitchusingawirenutprovided

• Locatethewhiteneutralwireinyourswitchboxandattach

tothewhitewireinthenewswitchusingaquickconnector

• Locatethegroundgreenorcopperwireinyourswitchbox

andattachtothegroundwireinthenewswitchusingawirenut

orquickconnector

6 Gently push the new, wired switch back into the switch box and

screw the switch plate in place using the provided machine screws.

Hardware used: CC Long machine screw x 

7 Attach faceplate (not included) over switch plate.

8 Turn on the power.

NOTE: The wall switch communicates wirelessly with the

fan/ light unit. Therefore, no wires are run from the switch

to the fan/light unit in the ceiling.

ISO|

WARNINGDISCONNECTPOWERSUPPLY

BEFORESERVICING

SEESAFETYINFORMATIONBEFOREPROCEEDING

ROUTINEMAINTENANCESHOULDBEDONEAT

LEASTONCEAYEAR

CAUTION

• Neverusesolventsthinnerorharshchemicalsfor

cleaningthefan

• Donotallowwatertoenterthemotor

• DonotimmerseplasticpartsinwateroverFC

 Unscrew the four () screws and carefully remove the glass

and metal assembly.

 Remove the  light bulbs and change as necessary.

 Remove the bell by pulling down with both hands.

CAREANDMAINTENANCE TODISASSEMBLE

ISO|

 Pull down on ceiling panel with both hands until it separates

from ceiling but is still suspended by the springs.

5 Disconnect the rainbow colored cable from the ceiling

panel by pulling on the connector.

 Remove the ceiling panel by squeezing the springs

and pulling down.

 Remove dust and dirt from the fan housing

with a vacuum cleaner.

 Dampen cloth with dish detergent, wipe the fan housing and

dry with a cloth. DO NOT USE abrasive cloth, steel wool pads,

or scouring pads.

 Replace the ceiling panel by following steps  under

installation in “New Construction”.

TOCLEAN

TOCHANGEALIGHTBULB

 Turn the fan light oﬀ.

 Unscrew the four () screws and carefully remove

the glass and metal assembly.

 Remove the necessary light bulb and discard.

 Screw in appropriate light bulb (see Installation

step for proper light bulb speciﬁcations).

 Reattach glass and metal assembly with the four ( screws.

ISO|

TROUBLESHOOTINGTIPS

PROBLEM POSSIBLECAUSES WHATTODO

THEREISAVISIBLE

GAPBETWEENTHE

CEILINGPANELAND

CEILING

The hole is smaller than

”x”cmxcm

Remove panel (refer to Care & Maintenance) and check to see

if fan was installed properly

Bottom edge of fan is

less than ⁄” cm) from

ceiling surface

Remove panel (refer to Care & Maintenance) and check to see

if fan was installed properly

THEFANSEEMS

LOUDERTHANIT

SHOULDBE

CFM too high CFMfanisdesignedforroomsuptosqsqm

Damper (exhaust port)

not working properly or

isdamaged.

Check exhaust ﬂap to ensure it is opening and closing properly.

If the exhaust fan has become damaged, please call Customer

Service

Bend in duct too close

tofandischarge.

Be sure you do not have any sharp bends in duct closer

than”cm) to the fan discharge

Fan body not securely

attached.

Be sure the fan is securely attached to your ceiling joists

Fan duct is being obstructed

at some point (including end

of duct)

Check the air duct to ensure the duct is not restricting air ﬂow

Fan may be clogged with

dust or debris

Refer to Care & Maintenance section for cleaning instructions

THEFANISNOT

CLEARINGTHE

HUMIDITYOUT

OFTHEROOM

Insuﬃcient intake airﬂow

within room.

The fan is not able to draw air out of the room without enough

airﬂow to draw from have a door or window slightly ajar or open

to allow airﬂow

Insuﬃcient CFM Be sure the CFM rating on the fan matches the requirements

for your room size. NOTE: If the fan clears steam from the room

within 15 minutes aer the shower has been turned oﬀ, the fan is

operating properly

Dust/dirt is clogging

fan intake

Refer to Care and Maintenance instructions

Duct may not be connected

tofan properly

Check air duct and fan connection to ensure that there

is a proper seal

ISO|

PROBLEM POSSIBLECAUSES WHATTODO

THEFANISNOT

TURNINGONIN

“AUTO”MODE

Humidity sensor PCB is not

connected

Please revisit the instruction manual and verify the wiring

of the wall switch and fan are properly connected

Sensor PCB was connected

while power was on

With sensor PCB still connected, restart power source

to the unit

NIGHTLIGHTNOT

TURNINGON Sensor is obstructed Using a damp cloth or rag, clean oﬀ the fan’s faceplate,

including the small half sphere sensor

Bulb is burnt out Check and replace night light bulb

Night light sensor is not

registering movement

Using a damp cloth or rag, clean oﬀ fan’s faceplate, including the

small half sphere sensor. Make sure the hanging part of the unit

is not obstructing the PIR sensor from detecting movement

THEREGULARLIGHT

ISNOTTURNINGON Bulb is burnt out Check and replace light bulb using the instructions on page 

Wiring could have

become loose

Check switch box wiring to ensure wiring is correct

THEFANISNOT

TURNINGOFF Humidity in the room is

still in target range for

fantostay activated

Turn oﬀ manually or wait for fan to re-calibrate

WATERDAMAGE/

LEAKINGONCEILING The vent/duct has

not been installed

correctly

Make sure the vent/duct is venting outward and not up

into the ceiling

ISO|

LIMITEDTHREEYEARWARRANTY

QUIRKYINC“QUIRKY”ORIGINALPURCHASE

PRODUCTWARRANTY

Quirky warrants to the original purchaser (“Purchaser”) of

thisQuirky product, for the period of three () years following

the date on which Purchaser purchases the product, that the

product shall be free of defects in design, assembly, material,

orworkmanship.

Quirky will refund or replace, at its option, any defective product

free of charge.

In order to qualify for this warranty, the Purchaser must provide

the defective product and a copy of the original receipt of

purchase to Quirky for inspection. The receipt of purchase must

indicate the product purchased, price paid, date of purchase, and

name of merchant.

To request service under this warranty, contact Quirky

at QUIRKY or questions@quirky.com and a Quirky

representative will provide instruction on how to proceed.

This warranty shall be null and void if Quirky determines that

the product has been improperly installed, altered or tampered

with in any way. This warranty does not protect against normal

use, wear and tear, or damage due to abuse.

THIS WARRANTY CONTAINS THE SOLE WARRANTY OF

QUIRKY. THERE ARE NO OTHER WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING THE IMPLIED WARRANTY OR

CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED

WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE

TERM OF THIS WARRANTY. IN NO EVENT SHALL QUIRKY BE

LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT OR

CONSEQUENTIAL DAMAGES SUCH AS, BUT NOT LIMITED TO,

LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR

USE OF ANY QUIRKY PRODUCT, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

Some jurisdictions do not allow exclusions or limitations on

implied warranties or incidental, consequential or other damages,

so the above exclusions and limitations may not apply to you.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: () this device may not

cause harmful interference, and () this device must accept any

interference received, including interference that may cause

undesired operation.

Caution: Changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment oﬀ

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit diﬀerent

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

This device complies with industry Canada licence exempt RSS

standard(s). Operation is subject to the following two conditions:

() this device may not cause interference, and () this device

must accept any interference, including interference that may

cause undesired operation of the device.

COMPLIANCE

ISO|

ULWARNINGSTATEMENT

Section  – General

READ AND SAVE THESE INSTRUCTIONS

 Preventariskofﬁreelectricshockorinjurytopersons

bycleaningandusermaintenancesuchaslubrication

 Unplugordisconnecttheappliancefromthepowersupply

beforeservicing

 WARNING To Reduce The Risk Of Fire Or Electric

Shock, Do Not Use This Fan With Any Solid State Speed

ControlDevice.

 WARNINGTOREDUCETHERISKOFFIREELECTRIC

SHOCKORINJURYTOPERSONSOBSERVETHE

FOLLOWING

aUsethisunitonlyinthemannerintendedbythe

manufacturerIfyouhavequestionscontactthe

manufacturer

bBeforeservicingorcleaningunitswitchpoweroﬀat

servicepanelandlocktheservicedisconnectingmeansto

preventpowerfrombeingswitchedonaccidentallyWhen

theservicedisconnectingmeanscannotbelockedsecurely

fastenaprominentwarningdevicesuchasatagtothe

servicepanel

 CAUTIONForGeneralVentilatingUseOnlyDoNotUse

ToExhaustHazardousOrExplosiveMaterialsAndVapors

Additionalsafetyinformationisincludedintheinstruction

manualonpage

ULWARNINGSTATEMENT

Section A – Installation Instructions

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable codes

and standards, including ﬁre rated construction.

b) Suﬃcient air is needed for proper combustion and

exhausting of gases through the ﬂue (chimney) of fuel burning

equipment to prevent back draing. Follow the heating

equipment manufacturer’s guideline and safety standards

such as those published by the National Fire Protection

Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected

to a GFCI (Ground Fault Circuit Interrupter) – protected

branch circuit.

Additional installation instructions are included in the instruction

manual on pages .

ULWARNINGSTATEMENT

Section B – User Servicing Instructions

All user servicing instructions are included in the instruction

manual on pages 

ISO|

CUSTOMERSUPPORT

For service and support, email us at questions@quirky.com

orcallQUIRKY

RINSISOX|rev

For service questions, contact Quirky at 1-866-578-4759.

For sales inquiries, contact Sylvane at 1-800-934-9194.

Quirky iso User manual

Brand: Quirky

Model: iso

Type: User manual

Download PDF

report

Quirky iso User manual

Quirky iso User manual

Related papers

Other documents