Symmons 0142-353GMRH Installation guide

Symmons
Brand
Symmons
Model
0142-353GMRH
Type
Installation guide

Symmons 0142-353GMRH is a robe hook for glass mounted applications. It is made from brass and nonmetallic materials plated in standard polished chrome finish. The robe hook is designed for tempered glass installations only and can accommodate glass with a thickness between 5/16" (8mm) and 3/8" (10mm). The installation process is straightforward and requires only a few simple steps. The robe hook comes with a limited lifetime warranty for residential installations and a 5-year warranty for commercial installations.

Symmons 0142-353GMRH is a robe hook for glass mounted applications. It is made from brass and nonmetallic materials plated in standard polished chrome finish. The robe hook is designed for tempered glass installations only and can accommodate glass with a thickness between 5/16" (8mm) and 3/8" (10mm). The installation process is straightforward and requires only a few simple steps. The robe hook comes with a limited lifetime warranty for residential installations and a 5-year warranty for commercial installations.

Model Number Specication
Dimensions
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Warranty
Glass Mounted Robe Hook
Operation & Maintenance Manual
0142-353GMRH
Note: Dimensions subject to change without notice.
For California Residents
WARNING: This product contains chemicals known to
the State of California to cause cancer, birth defects, or
other reproductive harm.
Compliance
0142-353GMRH Glass Mounted Robe Hook Robe hook for glass mounted applications made from
brass and nonmetallic materials plated in standard
polished chrome nish.
Measurements
A 2”, 51 mm
B
Glass Thickness Ref.
Min. 5/16”, 8mm
Max. 3/8”, 10 mm
C 3/8”, 10 mm
D (2x) Ø 1 7/8”, 48 mm
EHole Size
Ø 1/2”, 13 mm
AA
DD
BB
CC
EE
GLASS REFERENCE
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2016 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3189 REV 0 ■ 020516
Parts Breakdown
A
B
CD
E
GLASS REFERENCE
Tools Required
Allen Wrench (3/32”)
Installation
Installation
Problem Cause Solution
Finish is spotting Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then quickly
rinse with water.
D
E
1) Install robe hook base (E) and washer (D) to glass
panel from behind.
2) Install robe hook (A) and washer (C) to robe hook
base (E). Secure with set screw (B).
A
B
C
E
2
1
Note: Robe hook for tempered glass installations
only.
Número de modelo Especicaciones
Dimensiones
Garantía limitada de por vida: al ser adquirido por
el usuario nal para uso particular.
De 5 años: para uso comercial.
Consulte el sitio web www.symmons.com/warranty para
obtener información más completa sobre la garantía.
Garantía
Perchero instalado sobre vidrio
Manual de funcionamiento y mantenimiento
0142-353GMRH
Nota: Las dimensiones están sujetas a cambios sin previo aviso.
0142-353GMRH Perchero instalado sobre vidrio Perchero para instalar sobre vidrio, fabricado con latón
y materiales no metálicos recubierto con el acabado
estándar de cromo pulido.
Medidas
A 2”, 51 mm
B
Referencia del
grosor del vidrio
Mín. 5/16”, 8 mm
Máx. 3/8”, 10 mm
C 3/8”, 10 mm
D (2x) Ø 1 7/8”, 48 mm
ETamaño del oricio
Ø 1/2”, 13 mm
AA
DD
BB
CC
EE
IMAGEN DE REFERENCIA DEL VIDRIO
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Teléfono: (800) 796-6667 ■
Fax: (800) 961-9621
Copyright © 2016 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3189 REV 0 ■ 020516
Desglose de las piezas
A
B
CD
E
Herramientas necesarias
Llave Allen (3/32”)
Montaje
Montaje
Problema Causa Solución
El acabado se está manchando. Las partículas en el suministro de agua
pueden manchar el acabado.
Limpie el área del acabado utilizando
un paño suave, jabón neutro y agua, o
con un limpiador no abrasivo y luego
enjuague rápidamente con agua.
D
E
1) Coloque la base del perchero (E) y la arandela (D) en
la parte posterior de la placa de vidrio.
2) Coloque el perchero (A) y la arandela (C) en la base
del perchero (E). Sujételo con el tornillo de presión (B).
A
B
C
E
2
1
Nota: Perchero para instalar sobre vidrio
templado solamente.
IMAGEN DE
REFERENCIA
DEL VIDRIO
Numéro de modèle Spécications
Dimensions
Garantie à vie limitée–à l'acheteur initial pour les
installations du consommateur.
5 ans–pour des installations commerciales.
Se reporter au site www.symmons.com/warranty pour
des informations complètes concernant la garantie.
Garantie
Porte-peignoir monté sur verre
Manuel d'utilisation et d'entretien
0142-353GMRH
Remarque: Les dimensions sont sujettes à changement sans préavis.
0142-353GMRH Porte-peignoir monté sur verre Porte-peignoir pour montage sur verre à l'aide
d'accessoires en laiton et matériaux non
métalliques au ni chrome poli standard.
Mesures
A 2po, 51mm
B
Épaisseur de
référence du verre
Min. 5/16 po, 8mm
Max. 3/8 po, 10mm
C 3/8po, 10mm
D (2x)Ø17/8po, 48mm
ETaille du trou
Ø1/2po, 13mm
AA
DD
BB
CC
EE
RÉFÉRENCE POUR LE VERRE
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Téléphone: (800)796-6667 ■
Télécopieur: (800) 961-9621
Copyright © 2016 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3189 REV 0 ■ 020516
Liste des pièces
A
B
CD
E
Outils requis
Clef Allen (3/32 po)
Installation
Installation
Symptôme Cause Solution
Le ni est tâché. Les éléments présents dans l'eau
peuvent causer des tâches sur le ni.
Nettoyer la zone avec un chiffon doux
en employant de l'eau et du détergent
doux ou un nettoyant non abrasif et
rincer rapidement à l'eau.
D
E
1) Installez la base du porte-peignoir (E) et la rondelle
(D) au panneau de verre de l'arrière.
2) Installez le porte-peignoir (A) et la rondelle (C) à la
base du porte-peignoir (E). Fixez la poignée avec les
vis de pression (B).
A
B
C
E
2
1
Remarque: Porte-peignoir pour les installations
de verre trempé uniquement.
RÉFÉRENCE
POUR LE
VERRE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Symmons 0142-353GMRH Installation guide

Symmons
Brand
Symmons
Model
0142-353GMRH
Type
Installation guide

Symmons 0142-353GMRH is a robe hook for glass mounted applications. It is made from brass and nonmetallic materials plated in standard polished chrome finish. The robe hook is designed for tempered glass installations only and can accommodate glass with a thickness between 5/16" (8mm) and 3/8" (10mm). The installation process is straightforward and requires only a few simple steps. The robe hook comes with a limited lifetime warranty for residential installations and a 5-year warranty for commercial installations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers