Astria Fireplaces DRT63ST Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
DRT63ST
Category
Fireplaces
Type
Instruction Sheet

This manual is also suitable for

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1
KIT CONTENTS
• (1) ea. Safety Guard
• (2) ea. Mounting Brackets
• (2) ea. Spring Nut Clips
• (2) ea. Washer Screws
REQUIRED TOOLS
• Phillips Screwdriver
NOTE: This procedure requires two people.
GENERAL INFORMATION
This optional Safety Guard is designed to reduce the risk of burn injury
associated with incidental contact with the glass front on the fireplaces
listed in Table 1 (below) when it is installed and used in accordance
with both these installation instructions and the warnings, precautions,
and instructions included in the INSTALLATION INSTRUCTIONS and the
CARE AND OPERATION INSTRUCTIONS provided with your appliance.
Note: Improper or repeated installation and removal of the
optional Safety Guard could scratch, dent, or otherwise deface
the metal frame that surrounds the glass front on the appliance.
HEARTH PRODUCTS
KITS AND ACCESSORIES
P/N 506020-49
Rev. A 10/2014
MONTEBELLO and DRT/DRC6300 SERIES
GAS FIREPLACE
SAFETY GUARD KIT
INSTALLATION INSTRUCTIONS FOR SAFETY GUARD KIT
FOR USE ON MONTEBELLO and DTR/DRC6300 GAS FIREPLACE MODELS LISTED IN TABLE 1
Figure 1
Front Glass
Panel
INSTALLATION INSTRUCTIONS
Note: This procedure requires two people.
Step 1. If the fireplace is on, turn it OFF. Allow it to cool completely.
BEFORE CONTINUING, FIREPLACE MUST BE OFF AND COLD!
Step 2. See Figure 1. Remove the two existing screws from the top of
the Front Glass Panel.
Note: After removing screws, one person must hold the
glass panel in place (to prevent it from falling forward and
breaking), while another person completes the installation.
NOTICE
• READ ALL STEPS BEFORE STARTING INSTALLATION.
• THESE INSTRUCTIONS MUST BE LEFT WITH THE APPLIANCE.
• ALL WARNINGS, PRECAUTIONS, AND INSTRUCTIONS IN THE
INSTALLATION INSTRUCTIONS AND CARE AND OPERATION MANUALS
PROVIDED WITH THE APPLIANCE ALSO APPLY TO THESE INSTRUCTIONS.
• IF YOU ENCOUNTER ANY PROBLEMS, NEED CLARIFICATION OF THESE
INSTRUCTIONS, OR ARE NOT QUALIFIED TO PROPERLY INSTALL THIS KIT,
CONTACT YOUR LOCAL DISTRIBUTOR OR DEALER.
Remove two existing screws.
CAUTION
INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD!
Hot Fireplace Will Cause
Severe Burns
Never Allow Children to
Touch Glass or other Fire-
place Parts
WARNING
Figure 2
Front Glass
Panel
Figure 3
IMPORTANT! After removing screws, hold
Glass Panel in place so it will not fall out.
Step 3. See Figure 2. Insert the back lip of each Mounting Bracket
(without the hole) under the bottom edge of the Glass Panel.
Step 4. See Figure 3. Attach one Spring Nut Clip (with straight edge
facing front and down) to the front lip of each Mounting
Bracket, and then align the holes.
Insert back lip of each Mounting
Bracket (without hole) under
bottom edge of Glass Panel.
Attach Spring Nut Clips
(straight edge facing front and
down) to Brackets; align holes.
SAFETY GUARDS
Fireplace Application
Fireplace Model Safety Guard
Cat. No.
Safety Guard
Model No.
40" Models H8249 SG-13 [1]
45" Models H8251 SG-15 [1]
40" See-Thru Models H8315 SG-22 [2]
[1] Safety Guard models SG-13 and SG-15 are for indoor use only.
[2] Safety Guard model SG-22 is for outdoor use on Montebello
See-Through fireplace models.
Table 1
Mounting Bracket
(with hole in front)
Spring Nut Clip
P506020-49
2
Printed in U.S.A. © 2014 Innovative Hearth Products
P/N 506020-49 Rev. NC 10/2014
Innovative Hearth Products reserves the right to make
changes at any time, without notice, in design, materi-
als, specifications, and prices, and also to discontinue
colors, styles, and products. Consult your local distribu-
tor for fireplace code information. 1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.us.com
Step 6. See Figure 5. Align the holes in the top of the Safety Guard
with the holes in the top of the Front Glass Panel. Use a
Phillips screwdriver to replace the two screws previously
removed.
Align the holes in the lower front of the Safety Guard with the
holes in the Clips and Brackets. Use a Phillips screwdriver to
install the two supplied Washer Screws.
Install two supplied Washer Screws.
Step 5. See Figure 4. Slide the openings in the bottom edge of the
Safety Guard over the Spring Nut Clips.
Reinstall two screws previously removed.
P506020-49
INNOVATIVE HEARTH PRODUCTS• LINEAR ELECTRIC FIREPLACE• INSTALLATION INSTRUCTIONS
Front Glass
Panel
Safety
Guard
Figure 4
Figure 5
  • Page 1 1
  • Page 2 2

Astria Fireplaces DRT63ST Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
DRT63ST
Category
Fireplaces
Type
Instruction Sheet
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents