Hitachi CMPAT04 User manual

Brand: Hitachi

Model: CMPAT04

Type: User manual

Packed in a temporarily assembled condition

Hitachi Plasma Display Ceiling Mount Unit

Model

CMPAT04 Installation Instructions

Thank you for purchasing the Hitachi Plasma Display Ceiling Mount Unit.

To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual

in a safe place for future reference.

This plasma display ceiling mount unit is for use only with the following models :

CMP401X, CMP402HD, CMP307X

♦ Special techniques are necessary for installation of

the plasma display.

Do not attempt to perform this work by yourself.

♦ Request an installation specialist to install this unit.

♦ This company assumes absolutely no responsibility

for injuries and damages that may occur due to

improper installation and handling.

• To dealers and shops

• To ensure customer safety, be sure to design the

installation location so that the strength is sufficient

to withstand the weight of both the plasma display

and the Ceiling mount unit.

• Always use at least two persons for all

installations.

• Firmly install coupling pins, snap pins and screws

as specified in the installation instructions.

Parts Configuration Chart

In the parts packing

Parts for CMP401X only

Coupling pin

Usage cautions to ensure correct usage

• The following symbols are used to ensure safe usage of the product, to prevent danger to

yourself and other parties and to prevent damage to property.

Symbols

♦ This symbol indicates that incorrect handling due to ignoring this symbol

can result in the possibility of personal injury or even death.

♦This symbol indicates

additional cautions

(including warnings).

♦ This symbol indicates that incorrect handling due to ignoring this symbol

can result in the possibility of personal injury and physical damage.

♦This symbol indicates

forbidden actions.

♦This symbol indicates

required actions.

Ceiling mount unit

Snap pin

Angle

adjustment unit

(left) (right)

Display mount fitting

1 each left/right

18 screw

Support

M4 x 12 screw

WARNING

CAUTION

Caution

(general)

Forbidden

(general)

Required

(general)

Disassembly

prohibited

Indicates that the power

plug is to be disconnected

from the power outlet.

- 2 -

Safety Cautions

♦ When a malfunction occurs, disconnect the power plug

from the power outlet and take measures to prevent

other people coming near the plasma display.

In the cases such as

• The plasma display is loose and vibrates to an extreme degree,

• Mounting screws or parts are loose or missing,

failure to take appropriate actions can result in injury.

Perform the following actions immediately whenever a

malfunction occurs.

1.Turn off the plasma display power switch.

2.Disconnect the power plug from the power outlet.

Surround the area with rope, etc., to prevent other people coming near.

4.Contact your local dealer.

♦

Ask your dealer to install, move or adjust the angle

of the ceiling mount unit.

Incorrect installation or adjustment can cause the plasma display

to fall.

♦

The ceiling where the ceiling mount unit is to

be installed must fully support the weight of

the plasma display and the ceiling mount unit

for an extended period of time.

Take measures to fully withstand earthquake,

other vibration and external forces.

Incorrect installation can cause the plasma display to fall

and cause injury.

Total load of the (plasma display + ceiling mount unit) = 51kg

• Always use bolts, washers and nuts to firmly install on a

rigid construction member such as ceiling beam, etc.

• Do not mount directly on a ceiling of insufficient strength or

use wood screws or anchor screws that do not have

sufficient strength to reliably resist pulling out.

• When installing the ceiling mount unit on ceiling

construction members, use commercially available 10mm

nominal diameter screws that are appropriate for the

construction members.

10cm

or more

10cm

or more

10cm

or more

10cm

or more

♦

Avoid installing in

locations where the

temperature and

humidity are

excessively high,

and where contact

with water is

possible.

These can result in fire

or electrical shock.

♦

Do not block the

ventilation holes.

Also provide

sufficient clearance

in regard to the

surroundings to

avoid blocking the

ventilation.

The internal temperature

could elevate and

possibly result in fire.

Installation Location

Wood screw

Ceiling beam

10mm nominal dia.

bolt, spring washer,

washer, nut (4 each)

Contact your

local dealer.

Disconnect the

power plug from

the power outlet.

Handling by other than

professional contractors

is prohibited.

WARNING

CAUTION

- 3 -

Installing

♦

Do not install close

to an air-

conditioner intake

or outlet.

Do not install in

locations where

there is excessive

amounts of dust,

oily smoke or

tobacco smoke.

Fire could result.

♦

Do not install in

locations where

there is excessive

vibration or impact.

Injury and damage

could result from

falling.

♦

Do not install near

sprinklers or

sensors.

This could result in

misoperation or

electrical shock.

♦

Install only on a

horizontal surface.

Avoid sloped

surfaces. Also, do not

install facing upward.

The internal

temperature could

elevate and possibly

result in fire.

Injury or damage could

also result from falling.

CAUTION

WARNING

♦

Make sure the

plasma display

mount fittings and

angle adjustment

unit are firmly

engaged.

Failure to do so could

cause the plasma

display to fall.

♦

Do not alter any of

the parts. And do

not use broken

parts.

This could result in

injury due to the

plasma display falling.

♦

Always use at least

two people to

perform the

installation work.

Injury could result from

dropping heavy

objects.

♦

Firmly install

coupling pins, snap

pins and screws in

the prescribed

locations.

Failure to do so could

result in the plasma

display dropping.

♦ Do not loosen or

remove hex head

screws.

This could result in

insecure installation

and dropping.

- 4 -

Installation Method

Installation space

While referring to the dimensional drawing for the ceiling mount unit, decide an installation location where the

ceiling strength is sufficient. Also, set the height adjustment position, screen tilt angle and horizontal angle of the

ceiling mount unit beforehand.

CMP401X

CMP402HD

549

45 45

418549

(307)

(121)

940

97 55

366

742 235 180 (P60x3)

977

583

45 45

451583

(274)

(121)

1041

89 55

319

648 314 180 (P60x3)

969

Screen

center

Screen

center

- 5 -

513

45 45

398513

884

337

684

291 180 (P60 x 3)

100

975

(284)

(121)

CMP307X

Screen

center

Ceiling mount unit dimensions

330

300

Pipe dia.

61mm

Four 12mm dia. holes

300

330

Adjustment range

Height adjustment: 180mm (P60 x 3 steps)

Downward tilt angle adjustment: 0, 5, 10, 15, 20, 25 (6 steps)

Horizontal angle adjustment: 45 degrees left or right (continuous)

- 6 -

Installing the ceiling mount unit

1. Disassembly

•Slightly loosen the 4 lock

screws and 1 rotation stopper

screw.

Merely slightly loosen the

above screws. Do not remove

them.

•Pull out the 2 snap pins and

the 2 coupling pins.

•Separate the ceiling mount unit

and angle adjustment unit.

2. Downward tilt angle adjustment

•Remove 1 M6 x 18 screw from each side of the

angle adjustment unit. Align the hole for the

necessary screen tilt angle and then tighten the M6

x 18 screws. Be sure that both the left and right

sides are set to the same angle.

3. Installing on the ceiling

•Pass the wiring cable through the

ceiling mount unit as necessary.

•Install the ceiling mount unit on the

ceiling with the cable hole facing the

back.

•For the ceiling, use commercially

available bolts, washers and nuts that

are appropriate for the ceiling

construction.

Angle adjustment unit

Ceiling mount unit

remove the

2 coupling

pins.

Loosen the

1 rotation

stopper screw.

(Back)

(Front)

Loosen the

4 lock screws.

Remove the

2 snap pins.

M6 X 18 screw

300

Cable hole

Wiring cable

M10 bolt

Mounting hole:

12mm dia.

Ceiling mount unit

Flat washer

Spring washer

Nut

- 7 -

4. Installing the angle

adjustment unit

1. Pass the wiring cables

through the pipe, then insert

the angle adjustment unit

into the ceiling mount unit.

Adjust the height so that the

red mark on the pipe is not

visible and then insert the

two coupling pins.

Have two coupling pins

inserted into the linkage

holes in the angle adjustment

unit.

2. Insert snap pins into the

holes in the ends of the

coupling pins.

3. Tighten the 4 lock screws.

4. Adjust the horizontal angle of

the screen.

5. Tighten the one rotation

stopper screw.

Angle adjustment unit

Ceiling mount unit

5.Tighten the

rotation stopper

screw.

3.Tighten the

4 lock screws.

2.Insert 2 snap pins.

1.Insert the

2 coupling pins

4.Adjust the

horizontal angle.

This could cause the

plasma display to fall

if it is assembled to

make the red mark

visible.

Linkage hole

Red mark

Mounting the display mounting fittings on the plasma display

1. Remove the stand.

1. Place a protective sheet cover on the top of a

table and place the plasma display on the cover

with the back side upward.

2. Remove the screws fastening the column and pull

the column out in the direction indicated by the

arrow mark.

3. Remove the 4 screws fastening the stand and

remove the stand in the direction indicated by the

arrow mark.

Remove the screws.

CMP401X plasma

display

Table

Column

Stand

Remove 4 screws.

Stand

CMP401X

- 8 -

2. Installing the CMP401X supports

• Fasten the two supports to the back of the plasma

display with 4 M4

12 screws.

3. Installing the display mounts

• fasten the two display mounts to the back of the

plasma display with 6 M6

18 screws.

12 screws

(2 each)

Support fittings

1. Remove the top case of the cardboard box and

the polyethylene bag.

2. Mounting the display mount.

• Mount the display mounting fixtures (left / right) on

the back of the plasma display unit with the bent part

facing inward, then fasten with six M6

18 screws.

18 screws

(3 each)

Display mount

The top hole of the

display mount.

The 3rd display mount

hole from the top.

The top hole of the

plasma display.

The 6th display mount

hole from the top.

2nd display mount hole

from the top.

4th hole from the top.

5th hole from the top.

Align the

protrusion of

the support

with the

outer hole.

CMP402HD

1. Remove the stand.

• Remove the top case of the cardboard box and the

polyethylene bag.

When a stand is attached to the plasma display,

remove the four screws and detach the stand.

2. Mounting the display mount.

• Mount the display mounting fixtures (left / right) on

the back of the plasma display unit with the bent part

facing inward, then fasten with six M6

18 screws.

Remove 4 screws.

and remove the stand.

Stand

CMP307X plasma

display

18 screws

(3 each)

2nd display mount

hole from the top.

2nd plasma display

hole from the top.

CMP307X

Display mount

(right)

Display mount

(left)

Display mount

(right)

Display mount

(left)

18 screws

(3 each)

- 9 -

Installing the plasma display on the angle adjustment unit

♦ To fasten the plasma display to the ceiling mount unit, engage the four pins of the angle adjustment unit in the

four cutouts of the display mount fitting on the back of the plasma display. Next, tighten the two screws from the

bottom.

♦ When installation is complete, fasten the wiring cable with cable clamps as necessary.

Make sure that

the pins and

cutouts at both

the top and

bottom are

firmly engaged

Make sure that the

angle adjustment unit

holes and display

mount fitting screw

holes are aligned

before tightening the

screws.

• The plasma display

should always be

carried by at least

two persons.

• Disconnect all of the

plasma display

power cords and

cables.

Cable

clamp

Angle adjustment unit

Cutout

Display mount fitting

M6 X 18 screw

Product Specifications

External Dimensions

Mass 14kg

Main material Steel sheet

Surface treatment

Black electrodeposited baked paint

Angle adjustment

0, 5, 10, 15, 20, 25 degrees (6 steps)

Products mounted

Hitachi Plasma Displays CMP401X, CMP402HD and CMP307X

330

300

969

601 (CMP401X screen center)

633 (CMP402HD screen center)

628 (CMP307X screen center)

Four 12mm dia. holes

φ61

180 (P = 60

3 steps)

454

5 degrees

5 steps =

25 degrees

Horizontal angle

adjustment

45 degrees (continuous)

Vertical (tilt) angle

adjustment

180mm (P60mm X 3 steps)

Printed in Japan (JE)3

Digital Media Systems

Division

2-15-12 Nishi-Shimbashi, Minato-ku, Tokyo,

105-8430, Japan

(Hitachi Atago Annex)

(03) 3502-2111

Hitachi, Ltd.Tokyo Japan

Hitachi CMPAT04 User manual

Hitachi CMPAT04 User manual

Hitachi CMPAT04 User manual

Related papers

Other documents