Hobart EFT49L Installation, Use And Maintenance Instructions

Brand: Hobart

Model: EFT49L

Type: Installation, Use And Maintenance Instructions

ISTRUZIONI PER L’INSTALLAZIONE, L’USO E LA MANUTENZIONE

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

INSTRUCTIONS POUR L’INSTALLATION, L’EMPLOI ET L’ENTRETIEN

INSTALLATIONS-, BETRIEBS-UND WARTUNGSANLEITUNGEN

INSTRUCCIONES PARA LA INSTALACIÓN, EL USO Y EL MANTENIMIENTO

15/10/2007 Rev.1 160492

FRY-TOP ELETTRICO SERIE DOMINA

ELECTRIC GRIDDLE PLATE SERIES DOMINA

FRY-TOP ELECTRIQUE SERIE DOMINA

ELEKTRISCHE BRAT-UND GRILLPLATTEN SERIE DOMINA

FRY-TOP ELÉCTRICO SERIE DOMINA

EFT49L EFT99L EFT99LR

EFT49LC EFT99LC EFT99LRC

EFT49R EFT99R

EFT49RC EFT99RC

EFTA49L EFTA99L

EFTA49LC EFTA99LC

EFTA49R EFTA99R

EFTA49RC EFTA 99RC

0 6 9 4

- 10 -

SECTION DESCRIPTION PAGE

General notices .................................................................................................................................... 11

1. Technical data ..................................................................................................................................... 12

1.1 Electric fry-top .................................................................................................................................... 12

1.2 Technical characteristics ..................................................................................................................... 12

2. Installation instructions ...................................................................................................................... 12

2.1 Electric fry-top data plate .................................................................................................................... 13

2.2 Laws, regulations and technical directives ........................................................................................ 13

2.3 Place of installation ............................................................................................................................. 13

2.4 Positioning .......................................................................................................................................... 13

2.5 Electrical connection .......................................................................................................................... 13

2.5.1 Earthing ............................................................................................................................................... 13

2.5.2 Equipotential system ........................................................................................................................... 14

2.5.3 Power supply cable .............................................................................................................................. 14

2.5.4 Connections to the various electric mains .......................................................................................... 14

3. Replacing the most important components ........................................................................................ 15

4. User instructions .................................................................................................................................. 16

4.1 Using the electric fry-top..................................................................................................................... 16

4.2 Using the chrome plate ........................................................................................................................ 16

4.3 Safety thermostat ................................................................................................................................. 16

5. Maintenance and cleaning .................................................................................................................. 17

INSTALLATION DIAGRAM ............................................................................................................... 42

ELECTRICAL DIAGRAM EFT49-EFTA49 ....................................................................................... 44

ELECTRICAL DIAGRAM EFT99-EFTA99 ....................................................................................... 45

CONTENTS

- 11 -

- Read the instructions contained in this manual carefully as they provide important information on safe installation,

operation and maintenance procedures.

- Store this manual carefully for future reference by the operators.

- After removing the packing, check the integrity of the unit and, if in doubt, do not operate the unit, call professionally

qualified personnel.

- Before connecting the unit, make sure that the data on the plate correspond to those of the electric mains.

- This unit must only be used for the purposes for which it has been expressly designed, any other use is to be

considered improper and therefore dangerous.

- The unit must only be used by a specifically trained person.

- For any repairs, call solely a technical service centre authorized by the manufacturer and ask for genuine parts.

- Failure to comply with the above may jeopardize the safety of the unit.

- Never wash the unit with direct or high pressure jets of water.

- Do not obstruct air vents or heat dissipation openings.

- Electrical safety is guaranteed only by an efficient earthing system, as envisaged by the current electrical safety

regulations; it is therefore necessary to verify this essential requisite and, in case of doubt, ask professionally

qualified personnel to check it over thoroughly.

- The manufacturer cannot be deemed responsible for any damage caused by failure to earth the system.

- The unit must be included in an equipotential system whose efficiency must be tested according to the standards

in force.

- All units are supplied with a cable 2 m long having the characteristics stated in Tab. 3.

- The specifications of the power supply connection flexible cable must match or be superior to those of the cable

with rubber insulation H07RN-F.

GENERAL NOTICES

In the event of the user or the installation technician failing to observe the instructions given in this manual, the Firm

disclaims all responsibility thereof and cannot be held liable for any accidents or trouble caused by such non-observance.

THE MANUFACTURER DISCLAIMS ALL RESPONSIBILITY FOR ANY INACCURACIES IN THIS BOOKLET THAT MAY BE

DUE TO TYPING OR PRINTING MISTAKES. THE MANUFACTURER, MOREOVER, RESERVES THE RIGHT TO MAKE THE

MODIFICATIONS TO THE PRODUCT IT CONSIDERS USEFUL OR NECESSARY, WITHOUT AFFECTING ITS BASIC FEATURES.

- 12 -

1.1 ELECTRIC FRY-TOPS

1.2 TECHNICAL CHARACTERISTICS

Frame made of AISI 304 stainless steel, mounted on height-adjustable feet and with a rubber platform.

COOKING PLATE made of special steel with high thermal conductivity, in smooth and fluted versions, with splash guard

made of 18/10 stainless steel; C version with chrome worktop.

DRIP TRAY made of AISI 304 stainless steel.

ELECTRIC HEATING with armoured electrical heating elements.

INDEPENDENT CONTROLS for every plate zone for differentiated temperatures on EFT99 models.

Installation must be performed by qualified persons in accordance with current regulations.

WARNINGS:

If the oven is installed against a wall, the wall needs to withstand temperatures of 100°C and must be fireproof.

Before proceeding with the installation, remove the protective plastic film and eliminate any adhesive residues by means of

a suitable product for cleaning stainless steel.

Install the oven horizontally, correct positioning is obtained by turning the levelling feet.

If the unit is installed on its own, it is advisable to secure it to make its stability safer.

Tab. 1

L = Smooth plate R = Fluted plate LR = 50% smooth 50% fluted plate C = Chrome plate

*SUPPLY VOLTAGE: 3N AC 415 V; 3 AC 240 V; 1N 240 V 50/60 Hz.

N.B.: The input power with 3N AC 380 V; 3 AC 220 V; 1N 220 V 50/60 Hz is approximately 16% lower.

The input power with 3N AC 400 V; 3 AC 230 V; 1N 230 V 50/60 Hz is approximately 8% lower.

1. TECHNICAL DATA

2. INSTALLATION INSTRUCTIONS

EFT49L

EFT49LC

EFT49R

EFT49RC

EFT99L

EFT99LC

EFT99R

EFT99RC

EFT99LR

EFT99LRC

EFTA49L

EFTA99L

EFTA49LC

EFTA99LC

EFTA 49R

EFTA99R

EFTA49RC

EFTA99RC

MODEL DIMENSIONS in mm.

esternal plate

WxDxH/H max.

450x900x250/350

900x900x290/350

450x900x925

900X900X925

450X900X925

900X900X925

450X900X925

900x900x925

450X900X925

900X900X925

WxD

375x710

825x710

375x710

825X710

375X710

825X710

375X710

825x710

375X710

825X710

POWER

INPUT

TOTAL *

WEIGHT

NET

140

- 13 -

2.1 ELECTRIC FRY-TOP DATA PLATE

The technical data plate is under the bottom

edge of the instrument panel.

2.2 LAWS, REGULATIONS AND TECHNICAL DIRECTIVES

The following regulations must be observed during installation:

- Current accident and fire regulations.

- The regulations of the electric power supply company.

- Health regulations.

- Electrical systems standards.

2.3 PLACE OF INSTALLATION

- The unit should be installed in a room with adequate ventilation.

- Install the unit in compliance with the safety regulations.

2.4 POSITIONING

- The various units may be installed separately or combined with other units in the DOMINA range.

- This unit is not suitable for encasing.

- The distance from the side walls must be at least 10 cm.; should the distance be less or the material of the walls or floor be

flammable, it is vital to install heat insulation.

2.5 ELECTRICAL CONNECTION

The electrical connection must be made in compliance with CEI standards, only by authorized and skilled personnel.

Firstly, check the data given in the technical data table of this manual, on the data plate and in the wiring diagram. The

envisaged connection is of the fixed type.

IMPORTANT: A multi-polar mains cut-off device must be provided upstream from each oven, with a contact gap of at least

3 mm., for example:

- a manual switch of suitable capacity, equipped with fuses

- circuit breaker with relevant miniature circuit breakers.

2.5.1 EARTHING

It is vital to earth the oven.

Connect the terminals marked by the symbols (

) positioned on the line-in terminal block to an efficient grounding

complying with the regulations in force.

SPECIFIC WARNINGS

The electrical safety of this unit is assured only when it is connected correctly to an effective earthing system as stated in

the current electrical safety standards; the manufacturer accepts no liability if these safety standards are not met.

It is necessary to verify this fundamental safety requisite and, in case of doubt, ask for the system to be tested thoroughly by

professionally qualified personnel.

The manufacturer cannot be deemed responsible for any damage caused by failure to earth the system.

CAUTION: NEVER CUT THE EARTH WIRE (yellow-green).

2.5.2 EQUIPOTENTIAL SYSTEM

The oven must be included in an equipotential system whose efficiency must be checked according to the standards in force.

The screw marked with the ”Equipotential” label is on the back near the cable clamp.

Matr. N°

Mod.

- 14 -

2.5.3 POWER SUPPLY CABLE

The unit is delivered fitted for one of the following voltages:

3N AC 380...415 V; 3 AC 220...240 V;1N AC 220...240 V 50/60 Hz.

The specifications of the power supply connection flexible cable must match or be superior to those of the cable with rubber

insulation H07RN-F. Introduce the cable through the cable clamp and secure it firmly. During operation, the power supply

voltage should not differ from the voltage rating by +/-10%.

To access the terminal block in order to connect the unit to a supply mains with different characteristics to the ones envisaged,

or to replace the supply cable, you need to:

- remove the front panel

- connect the supply cable to the terminal block according to need, following the instructions given on the label located near

the terminal block and in this handbook.

2.5.4 CONNECTIONS TO THE VARIOUS ELECTRIC MAINS

3N AC 380...415 V 50/60 Hz.

Elements 240 V

2N AC 380...415 V 50/60 Hz.

Elements 240 V

3 AC 220...240 V 50/60 Hz.

Elements 240 V

PE (Earth) yellow-green

N (NP) blue

(T) black

(S) black

(R) brown

PE (Earth) yellow-green

N (NP) blue

(S) black

(R) brown

PE (Earth) yellow-green

(T) black

(S) black

(R) brown

1N AC 220...240 V 50/60 Hz.

Elements 240 V

PE (Earth) yellow-green

N (NP) blue

(R) brown

Tab. 2

- 15 -

The replacements described below should only be performed by an “Authorized Service Centre”.

Before replacing any component, you need to cut off power to the unit with the multi-polar switch.

A) Switch and thermostat

- remove the instrument panel

- undo the screws fastening the component

- disconnect the thermostat from the switch, carefully bending the two tabs of the bracket

- remove the thermostat bulb protection and take it out through the slit

- disconnect the wires, following the wiring diagram

- replace the component and reassemble everything, following the wiring diagram

- fit it all back together in reverse order to the above.

B) Heating elements

- disconnect the wires of the heating elements

- remove the heating element protection box

- remove the brackets fixing the heating element

- replace the part and reassemble everything, following the wiring diagram

Tab. 3

3. REPLACING THE MOST IMPORTANT COMPONENTS

2 3 4 5 6

380...415 V 3N

50/60 Hz

L2 L3 N PE

L2 N PE

380...415 V 2N 50/60 Hz

220...240 V 3 50/60 Hz

L1 N PE

220...240 V 50/60 Hz

N PE

The electrical connection plate is placed near the terminal board.

MODEL

EFT49L EFT49LC

EFT49R EFT49RC

EFTA49L EFTA49LC

EFTA49R EFTA49RC

TYPE OF SUPPLY

3N AC 380...415 V 50/60 Hz.

2N AC 380...415 V 50/60 Hz.

3 AC 220...240 V 50/60 Hz.

1N AC 220...240 V 50/60 Hz.

Mass.

A/f.

N° cables

8.3

16.66

14.4

5 x 1.5

4 x 2.5

4 x 1.5

3 x 4

Mass.

A/f.

N° cables

16.66

33.32

28.86

5 x 2.5

4 x 6

4 x 4

3 x 10

EFT99L EFT99LC

EFT99R EFT99RC

EFT99LR EFT99LRC

EFTA99L EFTA99LC

EFTA99R EFTA99RC

- 16 -

4.2 USING THE CHROME PLATE

SWITCHING ON: When the plate is just warm, grease it slightly with vegetable oil, then wait for the plate to reach the

required temperature.

COOKING: Optimum cooking is obtained at a temperature of approximately 200 ÷ 250°C. This temperature permits healthy

cooking without losing the main characteristics of the foods: taste, smell and appearance.

USE: The chrome plate does not absorb fat, as happens with traditional iron or cast-iron plates.

Cooking takes place all over the surface of the plate.

N.B. Never set the temperature higher than 250°C on the chrome plate.

4.3 SAFETY THERMOSTAT

The unit is equipped with a safety thermostat that limits the temperature in the event of the working thermostat malfunctioning.

To restore the safety thermostat, take off the rubber cap and press the red push-button.

Verify the causes of the action.

4.1 USING THE ELECTRIC FRY-TOP

Turn the thermostat control knob (Fig. 1 Pos. 1) clockwise to switch on the unit, shown by the green indicator light coming

on (Fig. 1 pos. 3). Continue turning the knob to set the required temperature as shown on the knob. The yellow indicator light

(Fig. 1 pos. 2) comes on to show that the plate heating elements are on; when it goes out, this means the temperature shown

on the knob has been reached.

The yellow indicator light comes back on whenever the required temperature on the plate has decreased by approximately

15°C and it will stay on until the plate reaches the required temperature again. To switch off, turn the knob anticlockwise to

take the “0” onto the limit position (indicator). The two yellow and green indicator lights will automatically go out.

4. USER INSTRUCTIONS

Fig. 1

- 17 -

5. MAINTENANCE AND CLEANING

- Clean the stainless steel parts every day with warm soapy water, then rinse thoroughly and dry carefully.

- You must never clean the stainless steel with steel wool, wire brushes or common steel scrapers since they may deposit

ferrous particles that on oxidizing cause rust points. Stainless steel wool may be used applied in the direction of the satin

finish.

- If the unit is not to be used for a long time, give all the steel surfaces a good wipe over with a cloth lightly soaked in Vaseline

oil in order to apply a protective film. Periodically ventilate the premises.

COOKING TOP

Clean the plate frequently with a wet rag, then switch it on for a few minutes in order to dry it. Afterwards, coat it with a light

layer of Vaseline oil.

CHROME PLATES

Clean the plate frequently with a wet rag. To remove any incrustations, use a strong plastic scraper at an angle, then dry the

plate with a rag. Afterwards, lubricate it with a light layer of Vaseline oil.

NEVER SCRAPE WITH POINTED OR SHARP METAL OBJECTS!

Use plastic tools that can withstand the temperature or stainless steel spatulas with rounded edges.

Caution: Never use the scraper on its edge as this would score the plate irreparably impairing its operation and making it hard

to clean. Replace the blade if it is not perfectly sharp.

STAINLESS STEEL PARTS

The stainless steel parts must also be cleaned with soapy water and then dried with a soft cloth.

You can keep it shining brightly by periodically wiping it over with liquid (POLISH), an easily available product.

- 42 -

EFT49 EFT99

Uscita cavo elettrico

Electric cable output

Sortie câble électrique

Elektrischkabel ausgang

Salida cable eléctrico

SCHEMI DI INSTALLAZIONE - INSTALLATION DIAGRAM

SCHEMAS D’INSTALLATION - INSTALLATIONSPLÄNE

ESQUEMAS DE INSTALACIÓN

- 43 -

SCHEMI DI INSTALLAZIONE - INSTALLATION DIAGRAM

SCHEMAS D’INSTALLATION - INSTALLATIONSPLÄNE

ESQUEMAS DE INSTALACIÓN

EFTA49L - EFTA99R

850

150

925

880

900

850

925

900

600

450

700

850

150

925

900

880

900

150

880

900

700

150

925

880

900

600

Attacco gas G3/4”

Gas connection G3/4”

Raccord gaz G3/4”

Gasanschluß G3/4”

Toma de gas G 3/4”

- 44 -

SCHEMA ELETTRICO - ELECTRICAL DIAGRAM

SCHEMA ELECTRIQUE - SCHALTPLAN

ESQUEMAS ELÉCTRICO

EFT49 - EFTA49

- 45 -

SCHEMA ELETTRICO - ELECTRICAL DIAGRAM

SCHEMA ELECTRIQUE - SCHALTPLAN

ESQUEMAS ELÉCTRICO

EFT99-EFTA99

- 46 -

- 47 -

EFT49-EFTA49

EFT99-EFTA99

ABBREVIAZIONE

SHORTNAME

ABREVIATION

KURZZEICHEN

ABREVIACION

N° CODICE

CODE n°

N° CODE

Nr. CODEX

N° CODICO

ITALIANO

FRANCAIS

ENGLISH

DEUTSCH

R1-R2-R3-

R4-R5-R6

TL1-TL2

LV1-LV2

LG1-LG2

CO1-CO2

TS1-TS2

RTBF900045

RTBF800038

RTBF600067

160505

160506

RTCU900007

RTCU800152

MORSETTIERA

RESISTENZA

TERMOSTATO 50-300°

LAMPADA VERDE

LAMPADA

ARANCIONE

COMMUTATORE

TERMOSTATO DI

SICUREZZA

CAVO DI

ALIMENTAZIONE

RACCORD

RESISTENCE

THERMOSTAT 50-300°

LAMPE VERTE

LAMPE

ORANGE

COMMUTATEUR

LIMITE

THERMOSTAT

CABLE

D’ALIMENTATION

TERMINAL BOARD

RESISTANCE

THERMOSTAT 50-300°

GREEN LAMP

ORANGE

LAMP

SWITCH

LIMIT THERMOSTAT

POWER SUPPLY

CABLE

KLEMMENLEISTE

HEITZKORPER

THERMOSTAT 50-300°

GRUENE LAMPE

ORANGE

LAMPE

HAUPTSCHATER

SICHERHEITS

THERMIOSTAT

ANSCHLUSSKABEL

ESPAÑOL

REGLETA

RESITENCIA

TERMOSTATO 50-300°

BOMBILLA VERDE

BOMBILLA

ANARANJADO

CONMUTADOR

TERMOSTATO

LIMITE

CABLE

D’ALIMENTACION

ABBREVIAZIONE

SHORTNAME

ABREVIATION

KURZZEICHEN

ABREVIACION

N° CODICE

CODE n°

N° CODE

Nr. CODEX

N° CODICO

ITALIANO

FRANCAIS

ENGLISH

DEUTSCH

R1-R2-R3

TL1

LV1

LG1

CO1

TS1

RTBF900045

RTBF800038

RTBF600067

160505

160506

RTCU900007

RTCU800152

MORSETTIERA

RESISTENZA

TERMOSTATO 50-300°

LAMPADA VERDE

LAMPADA

ARANCIONE

COMMUTATORE

TERMOSTATO DI

SICUREZZA

CAVO DI

ALIMENTAZIONE

RACCORD

RESISTENCE

THERMOSTAT 50-300°

LAMPE VERTE

LAMPE

ORANGE

COMMUTATEUR

LIMITE

THERMOSTAT

CABLE

D’ALIMENTATION

TERMINAL BOARD

RESISTANCE

THERMOSTAT 50-300°

GREEN LAMP

ORANGE

LAMP

SWITCH

LIMIT THERMOSTAT

POWER SUPPLY

CABLE

KLEMMENLEISTE

HEITZKORPER

THERMOSTAT 50-300°

GRUENE LAMPE

ORANGE

LAMPE

HAUPTSCHATER

SICHERHEITS

THERMIOSTAT

ANSCHLUSSKABEL

ESPAÑOL

REGLETA

RESITENCIA

TERMOSTATO 50-300°

BOMBILLA VERDE

BOMBILLA

ANARANJADO

CONMUTADOR

TERMOSTATO

LIMITE

CABLE

D’ALIMENTACION

INFORMAZIONE AGLI UTENTI

AI SENSI delle Direttive 2002/95/CE, 2002/96/CE e 2003/108/CE, relative alla riduzione dell’uso di sostanze pericolose nelle

apparecchiature elettriche ed elettroniche, nonché allo smaltimento dei rifiuti.

Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla confezione, indica che il prodotto alla fine della propria vita utile

deve essere raccolto separatamente dagli altri rifiuti.

La raccolta differenziata della presente apparecchiatura giunta a fine vita è organizzata e gestita dal produttore. L’utente che vorrà disfarsi

della presente apparecchiatura dovrà quindi contattare il produttore e seguire il sistema che questo ha adottato per consentire la raccolta

separata dell’apparecchiatura giunta a fine vita.

L’adeguata raccolta differenziata per l’avvio successivo dell’apparecchiatura dismessa al riciclaggio, al trattamento e allo smaltimento

ambientalmente compatibile contribuisce ad evitare possibili effetti negativi sull’ambiente e sulla salute e favorisce il reimpiago e/o riciclo

dei materiali di cui è composta l’apparecchiatura.

Lo smaltimento abusivo del prodotto da parte del detentore comporta l’applicazione delle sanzioni amministrative previste dalla normativa vigente.

USER INFORMATION

Pursuant to the 2002/95/CE, 2002/96/CE and 2003/108/CE Directives concerning the reduction in the utilisation of dangerous

substances in electric and electronic equipment, as well as waste disposal.

The symbol of the crossed rubbish skip on the equipment or on the package indicates that the product must be separated from other

waste at the end of its useful life.

The differentiated collection of this equipment is organised and managed by the producer. The user who intends to get rid of this equipment

shall contact the producer and follow the system that the latter has used in order to collect the equipment separately at the end of its life.

The proper differentiated collection in order to start the following recycling, treatment and disposal of the disused equipment in

compliance with the environment helps to avoid possible negative effects on the environment and on health, and favours the reutilisation

and/or recycling of the materials forming the equipment.

The unauthorised disposal of the product by the holder implies applying administrative penalties provided by the regulations in force.

INFORMATIONS DESTINÉES AU CLIENT

Conformément aux Directives 2002/95/CE, 2002/96/CE et 2003/108/CE concernant la réduction des substances dangereuses

dans les appareils électriques et électroniques ainsi que le traitement des déchets.

Le pictogramme de la benne barrée reportée sur l’appareil ou sur l’emballage indique que l’appareil, à la fin de sa vie, doit être traité sé-

parément des autres déchets.

La collecte différentiée de cet appareil ayant atteint la fin de sa vie est organisée et gérée par le fabricant. Le client souhaitant se défaire de cet appareil

devra donc contacter le fabricant et suivre la procédure que ce dernier a adoptée afin de permettre la collecte séparée de l’appareil arrivé en fin de vie.

La collecte différentiée adéquate permettant le recyclage successif de l’appareil et un traitement compatible avec l’environnement contri-

bue à prévenir les impacts négatifs sur l’environnement et la santé des personnes ainsi qu’à favoriser la réutilisation et/ou le recyclage

des matériaux qui composent l’appareil.

Le traitement illégal de l’appareil par son propriétaire entraîne l’application des sanctions administratives prévues par la législation en vigueur.

INFORMATION FÜR DIE BENUTZER

IM SINNE der Richtlinien 2002/95/EG, 2002/96/EG und 2003/108/EG zur Beschränkung der Verwendung bestimmter gefähr-

licher Stoffe in Elektro- und Elektronikgeräten und zur Entsorgung der Abfälle.

Das auf dem Gerät oder auf der Packung vorhandene Symbol eines gekreuzten Müllcontainers weist darauf hin, dass das Produkt nach

Ende seiner Nutzungsdauer von anderen Abfällen getrennt zu sammeln ist.

Die getrennte Sammlung dieses Geräts nach Ende seiner Nutzungsdauer wird vom Hersteller organisiert und verwaltet. Der Benutzer,

der sich von diesem Gerät befreien will, muss sich daher mit dem Hersteller in Verbindung setzen und das System befolgen, das der

Hersteller für die getrennte Sammlung des Geräts nach Ende seiner Nutzungsdauer eingeführt hat.

Eine angemessene getrennte Sammlung für die spätere Zuführung des abgelegten Geräts zum Recyling, zur Behandlung und zur um-

weltfreundlichen Entsorgung trägt dazu bei, mögliche negativen Auswirkungen auf die Umwelt und auf die Gesundheit zu vermeiden

und begünstigt die Wiederverwertung und/oder das Recycling der Werkstoffe, aus denen das Gerät besteht.

Eine rechtswidrige Produktentsorgung durch den Besitzer führt zur Auferlegung der von den einschlägigen Normvorschriften vorgese-

henen Verwaltungssanktionen.

INFORMACIÓN A LOS USUARIOS

Según las Directivas 2002/95/CE, 2002/96/CE y 2003/108/CE, relativas a la reducción del uso de sustancias peligrosas en los

aparatos eléctricos y electrónicos, así como a la gestión de los residuos.

El símbolo del contenedor tachad que aparece en los aparatos o en los envases, indica que el producto, al final de su vida útil debe

recogerse separado de los otros residuos.

La recogida diferenciada de este aparato una vez llegado el fin de su vida útil es organizada y gestionada por el productor. El usuario que

desee deshacerse de este aparato deberá, pues, ponerse en contacto con el productor y seguir el sistema adoptado por éste para permitir la

recogida separada del aparato al final de su vida útil.

La adecuada recogida diferenciada para el posterior reciclaje, tratamiento y desguace ambientalmente compatible del aparato contribuye a evitar

posibles efectos negativos sobre el ambiente y la salud y favorece la reutilización o el reciclaje de los materiales de que está compuesto el aparato.

El desguace abusivo del producto por parte del propietario comporta la aplicación de las sanciones administrativas previstas por la normativa vigente.