English
Español
Nederlands
Owner's Manual
EXOTIK PRE-AMPLIFIER
i
Important Safety Information
Important Safety Information
Explanation of symbols used in this manual and on the product:
This symbol is intended to alert the user to the presence of uninsulated
dangerous voltages within the enclosure of sufficient magnitude to cause
electric shock.
This symbol is intended to alert the user to the presence of important operation,
maintenance and servicing information in the instruction and service manuals.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
REPLACE THE MAINS FUSE IN THE PLUG WITH ONE OF THE SAME TYPE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
SHOCK HAZARD. DO NOT OPEN.
MAINS PLUGS
This appliance is supplied with a non-rewireable mains plug for the intended country.
Replacement mains leads can be obtained from your Linn retailer. Should you need to
change the plug please dispose of it carefully. A plug with bared conductors is
dangerous if engaged in a live socket.
The Brown wire must be connected to the Live (Line) supply pin.
The Blue wire must be connected to the Neutral supply pin.
The Green/Yellow wire must be connected to the Earth (Ground) supply pin.
Please contact your retailer or a competent electrician if you are in any doubt.
GENERAL SAFETY INSTRUCTIONS
11.. RReeaadd iinnssttrruuccttiioonnss..
Read the safety and operating instructions before operating the appliance.
22.. RReettaaiinn iinnssttrruuccttiioonnss..
Retain the safety and operating instructions for future reference.
33.. HHeeeedd wwaarrnniinnggss..
Observe all warnings on the appliance and in the operating instructions.
44.. FFoollllooww iinnssttrruuccttiioonnss..
Follow all operating and use instructions.
55.. WWaatteerr aanndd mmooiissttuurree..
Do not use the appliance near water, for example near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool and the like.
66.. CCaarrttss aanndd ssttaannddss..
Use only with a cart or stand that is recommended by the manufacturer.
66aa..
An appliance and cart combination should be used with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to overturn.
77.. WWaallll oorr cceeiilliinngg mmoouunnttiinngg..
Mount to a wall or ceiling only as recommended by the manufacturer.
88.. VVeennttiillaattiioonn..
Site the appliance so that its location or position does not interfere with its proper ventilation.
For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the
ventilation openings, or placed in a built-in installation such as a bookcase or cabinet that may impede the
flow of air through the ventilation openings.
99.. HHeeaatt..
Site the appliance away from heat sources such as radiators, heaters, stoves, or other appliances
(including amplifiers) that produce heat.
1100.. PPoowweerr ssoouurrcceess..
Connect the appliance to a power supply only of the type described in the operating
instructions or marked on the appliance.
1111.. GGrroouunnddiinngg oorr ppoollaarriissaattiioonn..
Do not defeat the safety purpose of the polarised or grounding type plug. A
polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
1122.. PPoowweerr ccoorrdd pprrootteeccttiioonn..
Route power cords so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs, power sockets, and at the point
where they exit from the appliance.
1133.. MMaaiinnss pplluugg..
Use the mains plug to disconnect the product from the mains supply. The mains plug must be
accessible at all times. Use the mains switch (if applicable) when the product is not in use.
1144.. CClleeaanniinngg..
The product should be cleaned only as recommended by the manufacturer.
1155.. PPoowweerr lliinneess..
An outdoor antenna should be located away from power lines.
1166.. OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg..
If an outdoor antenna is connected to the tuner/receiver, ensure that the
antenna system is grounded to provide some protection against voltage surges and static build up. In the
USA see article 810 of the National Electrical Code ANSI/NFPA 70 concerning installation requirements.
1177.. LLiigghhttnniinngg ssttoorrmmss..
Unplug this apparatus during lightning storms or when unused for long periods of time.
1188.. OObbjjeeccttss aanndd lliiqquuiidd eennttrryy..
Do not let objects or liquids fall into the product. Do not expose the product to
dripping or splashing. Do not place a vessel containing liquid on top of the product.
1199.. DDaammaaggee rreeqquuiirriinngg sseerrvviiccee..
The product should be serviced by qualified personnel if:
a) The power cord or plug has been damaged.
b) Objects or liquid have fallen into the product.
c) The product has been exposed to rain.
d) The product does not appear to operate normally or exhibits a marked change in operation.
e) The product has been dropped or the enclosure damaged.
2200.. SSeerrvviicciinngg..
Do not attempt to service the product beyond that described in the operating instructions. All
other servicing should be referred to qualified service personnel.
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
UK USERS PLEASE READ THIS
IMPORTANT SAFETY INFORMATION
Fuse replacement
This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug contains a
5 Amp fuse. If the fuse has blown it can be replaced as follows:
a) Pull out the red fuse cover/carrier.
b) Remove and dispose of the blown fuse.
c) Fit a new 5 Amp BS1362 approved fuse into the carrier and push the carrier
back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the plug.
Contact your Linn retailer to obtain a replacement fuse cover.
Fuses are for fire protection and do not protect against electric shock.
Mains plug replacement
Should your mains plug need replacing and you are competent to do this proceed as
follows. If you are in doubt contact your Linn retailer or a competent electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection points of most
quality plugs.
Attach the wires securely to their respective points. The Brown wire must go to the Live
pin, the Blue wire must go to the Neutral pin, and the Green/Yellow wire must go to the
Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding the outer
sheath of the cable firmly and that the wires are correctly connected.
WARNING
THIS APPLIANCE MUST BE EARTHED.
CE Declaration of Conformity
Linn Products Ltd declare that this product is in conformance with the Low Voltage Directive 73/23/EEC and
Electromagnetic Compatibility 89/336/EEC as amended by 92/31/EEC and 93/68/EEC.
The conformity of the designated product with the provisions of Directive number 73/23/EEC (LVD) is proved by
full compliance with the following standards:
SSttaannddaarrdd nnuummbbeerr DDaattee ooff iissssuuee TTeesstt ttyyppee
EN60065 2002 General requirements
Marking
Hazardous radiation
Heating under normal conditions
Shock hazards under normal
operating conditions
Insulation requirements
Fault conditions
Mechanical strength
Parts connected to the mains supply
Components
Terminal devices
External flexible cords
Electrical connections and mechanical fixings
Protection against electric shock
Stability and mechanical hazards
Resistance to fire
The conformity of the designated product with the provisions of Directive number 89/336/EEC (EMC) is proved by
full compliance with the following standards:
SSttaannddaarrdd nnuummbbeerr DDaattee ooff iissssuuee TTeesstt ttyyppee
EN55013 2001 Conducted emissions
EN55013 2001 Absorbed emissions
EN55020 2002 Immunity
FCC notice
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
ii
Important Safety Information
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
Copyright and Acknowledgements
Copyright © 2004 Linn Products Ltd. First edition April 2004.
Linn Products Limited, Glasgow Road, Waterfoot, Eaglesham, Glasgow, G76 OEQ,
Scotland, United Kingdom
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of the
publisher.
Printed in the United Kingdom.
Trade marks used in this publication:
LLiinnnn
and the Linn logo are registered trade marks
of Linn Products Limited.
EEXXOOTTIIKK
,
UUNNIIDDIISSKK
,
KKLLIIMMAAXX
,
LLIIMMBBIIKK
and
KKNNEEKKTT
are trade
marks of Linn Products Limited.
EXOTIK+DA additional acknowledgements:
"DTS", "DTS-ES" and “DTS 96/24” are trade marks of Digital Theater Systems, Inc.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trade marks of Dolby Laboratories.
The content of this manual is furnished for information use only, is subject to change
without notice, and should not be construed as a commitment by Linn Products Limited.
Linn Products Limited assumes no responsibility or liability for any errors or
inaccuracies that may appear in this manual.
Linn Products Limited disclaims any proprietary interest in trade marks and trade names
other than its own.
iii
Copyright and Acknowledgements
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
Contents
Introduction 1
Audio formats (EXOTIK+DA) 1
Cleaning
1
Connecting 2
Unpacking 2
Connecting to the mains supply 2
Positioning 2
Back panel 3
Front Panel and Handset 4
Front panel display 4
Front panel layout 4
Handset 5
Setup 6
Connecting 6
Setup menus 6
Using the setup menus 7
Speaker Setup 7
Source Setup 9
Audio Setup 11
General Setup 12
Installer Menu 15
Using the EXOTIK with a Linn UNIDISK player 16
Operation 17
Standby key 17
Selecting a source 17
Adjusting the audio 17
Volume 17
Balance 17
Volume trim 17
Lip Sync Delay (EXOTIK+DA) 18
Surround sound formats 18
Midnight Movie mode (EXOTIK+DA) 20
Restoring the original audio settings 20
Record function 21
Technical Specification 22
Guarantee and Service 23
Contents
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
Introduction
The EXOTIK pre-amplifier has been designed to provide superb audio performance with
both two- and multi-channel source material. This product uses technology developed
for Linn’s award-winning flagship KLIMAX Kontrol pre-amplifier and offers purist audio
performance and access to and control of the new generation of multi-channel sound
formats.
Two variants of the product offer different levels of functionality to suit your
requirements:
The standard EXOTIK is a multi-channel analogue unit supporting bass redirect, stereo
sub algorithm and 5.1 to 2 channel downmix.
EXOTIK+DA is an enhanced product which offers all the features of the standard EXOTIK
with the addition of a digital audio module for processing of all major audio algorithms,
including Dolby Digital 5.1, Pro Logic II, DTS Surround and DTS 96/24.*
The EXOTIK pre-amplifier exemplifies a commitment by Linn to new products which can
take advantage of the latest technology and audio formats whilst continuing to support
existing Linn customers with improved performance and superb value.
Important notes:
When the unit is in standby, either EXOTIK or EXOTIK+DA is shown on the front panel
display to indicate the product variant.
In this manual ‘EXOTIK’ refers to both the standard and the EXOTIK+DA versions of the
product. ‘Standard EXOTIK’ and ‘EXOTIK+DA’ refer specifically to the variants.
*The digital audio module is available as an upgrade for the standard EXOTIK.
Audio formats (EXOTIK+DA)
The surround sound algorithms supplied with the EXOTIK+DA include:
Along with Linn’s proprietary LIMBIK algorithm.
Note:
A full list of the algorithms is detailed in the
Surround sound formats
section of the
Operation
chapter.
Cleaning
Disconnect the EXOTIK from the power supply before cleaning. Remove dust and
fingerprints with a soft, dry cloth. Avoid using domestic cleaning products on the unit.
Introduction
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
1
DDoollbbyy PPrroo LLooggiicc IIII,, DDoollbbyy DDiiggiittaall EEXX
DDTTSS 9966//2244,, DDTTSS--EESS
Connecting
This chapter explains how to install the EXOTIK pre-amplifier into your hi-fi/AV system.
Unpacking
The EXOTIK is supplied with the following accessories:
●
luminescent handset with booklet
●
2 x R03 (AAA) batteries for the handset
●
1 pair of black interconnect cables
●
RS232 lead (for connecting the EXOTIK to a Linn UNIDISK player to allow
communication between the two units)
●
mains lead
●
this manual
We recommend you retain the packaging for reuse in case you need to transport the unit
at any time.
Connecting to the mains supply
Manual voltage selection is not required as the EXOTIK operates from any mains AC
power. There are no user-replaceable fuses inside the unit. The mains lead supplied may
be fitted with a fused plug according to local regulations. If this is the case, always
replace this fuse with another of the same type and rating.
The EXOTIK must always be earthed when connected to the mains supply. Use
the earthed mains lead supplied. Never use an unearthed plug or adapter with
this unit.
Positioning
You can locate your EXOTIK anywhere you find convenient (including in a 19” rack), but
there are a few simple points to note regarding positioning:
●
The IR sensor that receives the handset signals is quite sensitive, so the unit
should be kept out of direct sunlight to avoid false operation. The IR beam from
the handset will pass through semi-opaque glass so operation behind, for example,
smoked-glass cabinet doors is possible.
●
Never block the ventilation slots on the top and sides of the unit.
●
The unit should be protected from anything that generates significant amounts of
heat, such as radiators or power amplifiers.
Connecting
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
2
Back panel
CCoonnnneeccttoorr ggrroouupp nnaammee:: CCoonnnneeccttiioonn ffuunnccttiioonn CCoonnnneeccttoorr
CCoonnnneeccttoorr mmaarrkkiinngg ttyyppee
AANNAALLOOGGUUEE AAUUDDIIOO
One 7.1 analogue audio output. The SURR outputs 8 x RCA
OOUUTTPPUUTTSS:: FFRROONNTT LL--RR,,
are for connection to the two surround
SSUURRRR LL--RR,, SSUURRRR BBKK
loudspeakers in a 5.1 system. The SURR BK outputs
LL--RR,, CCEENNTTRREE,, SSUUBB
are for connection to the
two additional loudspeakers
in a 7.1 system - located at the rear of the room.
For two-channel systems, use the FRONT outputs
(and SUB if required) only
RREEMMOOTTEE:: IINN,, OOUUTT
RC5 in/out local loop for use in a KNEKT system 2 x RCA
AACCCC//RRCCUU
For installing the EXOTIK in a KNEKT
1 x RJ45
system or for connection to an infrared repeater
11 ttoo 44,, MMAAIINN
Used if the EXOTIK is part of a KNEKT system 5 x RJ45
IIRR:: 11,, 22
Pass IR commands to auxiliary devices 2 x 3.5 mm jack
RRSS223322:: IINN,, OOUUTT
Pass control instructions to and from the EXOTIK. 2 x RJ12
The OUT connection is used if you want to let
the EXOTIK control another device e.g. a Linn
UNIDISK player. The IN connection is used
if you want to control the EXOTIK from a third-
party home theatre controller
3
Connecting
POWER
TAPE OUT
L
1243/CENTRE2/SURR
SUB5.1 GROUP
SUB
1/FRONTFRONT SURR SURR BK CENTREIN
1
1
2
3 MAIN
SEE UNDERSIDE FOR SAFETY DETAILS
24ACC/RCU
OUT
56
3
**
OUT 1 3INPUTS 2
OUT
R
L
R
L
R
OUT RS232 IN
OFF
ON
ANALOGUE AUDIO INPUTS SPDIF TOSLINKANALOGUE AUDIO OUTPUTSREMOTEIR
1 2
347912 58 6101113
CCoonnnneeccttoorr ggrroouupp nnaammee:: CCoonnnneeccttiioonn ffuunnccttiioonn CCoonnnneeccttoorr
CCoonnnneeccttoorr mmaarrkkiinngg ttyyppee
OOFFFF,, OONN
Mains power switch -
NNoo nnaammee oorr mmaarrkkiinngg
Mains power inlet IEC
TTOOSSLLIINNKK:: OOUUTT,,
One optical digital audio output and three inputs 4 x TOSLINK
IINNPPUUTTSS 11 ttoo 33
SSPPDDIIFF:: OOUUTT,, IINNPPUUTTSS
One electrical digital audio output and three inputs 4 x RCA
11 ttoo 33
AANNAALLOOGGUUEE AAUUDDIIOO
Three stereo analogue L-R audio inputs 6 x RCA
IINNPPUUTTSS:: 44 LL--RR,, 55 LL--RR,,
66 LL--RR
AANNAALLOOGGUUEE AAUUDDIIOO
One 5.1 analogue audio input or three stereo 6 x RCA
IINNPPUUTTSS:: 55..11 GGRROOUUPP --
analogue L-R audio inputs
11//FFRROONNTT LL--RR,, 22//SSUURRRR
LL--RR,, 33//CCEENNTTRREE LL,, SSUUBB RR
TTAAPPEE OOUUTT:: LL--RR
One analogue L-R output for connection to a 2 x RCA
recording device e.g. DAT recorder
*EXOTIK+DA
1
2
5
6
7
4
3
9
10
11
12
13
8
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
Switch off the EXOTIK before connecting plugs to, or disconnecting plugs from, the
back panel to avoid generating an electrical surge that may damage the unit or other
components of your AV system.
Using the EXOTIK with a Linn UNIDISK player
For information on how to connect and set up your EXOTIK to a Linn UNIDISK player,
see the section at the end of the
Setup
chapter.
*
*
Front Panel and Handset
Front Panel and Handset
Front panel display
The front panel display shows you information regarding what you are listening to.
The current volume, current source, or both can be displayed along with the input audio
signal and processing algorithm.
The display also shows the setup menus and other information depending on the current
operation.
Front panel layout
142
3
5
FFrroonntt ppaanneell ddiissppllaayy
SSEELLEECCTT
Selects/executes options and certain commands. Used for accessing Setup Menus
SSOOUURRCCEE --
/
++
, / Change source, for adjusting settings
((ssttaannddbbyy))
Brings unit out of, or puts into, standby mode
VVOOLLUUMMEE --
/
++
, / Adjust the volume level, navigate setup menus and adjust settings
1
2
5
4
3
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
4
Front Panel and Handset
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
5
Handset
1.
AAUUDDIIOO AADDJJ
Adjusts loudspeaker balance and trim
2.
LLIIPP SSYYNNCC
Adds time delay to the audio signal*
3.
((mmuuttee))
Mutes/unmutes the audio output
4.
SSUURRRR
Selects a surround sound format
5.
VVOOLL -- // ++
Adjust the volume level
6.
CCDD
Selects a CD source
7.
AAUUXX
Selects an auxiliary source
8. For navigating setup menus and adjusting settings
9.
SSEETTUUPP
Enters/exits the setup menus
((ssttaannddbbyy))
Brings unit out of, or puts into, standby mode
11.
TTVV
Puts handset into TV mode
TTUUNNEERR
Selects a tuner source
13.
DDVVDD
Selects a DVD source
‘‘eenntteerr’’
Selects/executes options and certain commands.
Is used for accessing Setup Menus
((rreeccoorrdd))
For setting up a record path
KKNNEEKKTT kkeeyyss
Used if the unit is installed in a KNEKT system
Keys and functions not listed above do not function with the
EXOTIK but may with other Linn products.
Note:
If your EXOTIK is not responding as expected to handset keys, it is
likely that the handset is in TV mode. To correct this press any of
the source keys (DVD, CD, TUNER or AUX) on the handset.
*EXOTIK+DA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
11
12
13
15
16
14
10
9
6
Setup
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
Setup
Connecting
The first stage in setting up your EXOTIK is to connect your sources, power amp(s) and
other peripheral devices to the EXOTIK.
1. Ensure your EXOTIK and all components that you will be connecting to the EXOTIK
are disconnected from the mains supply.
2. Connect your source components, power amp(s) and any communication/control
devices you wish to use, referring to the back panel diagram in the
Connecting
chapter.
3. Connect the EXOTIK to the mains supply and turn the unit on using the switch on
the back panel. The front panel will display EXOTIK or EXOTIK+DA, depending on
your unit.
4. Press the key on the front panel or handset.
The main stage in setup is configuring the EXOTIK pre-amplifier to suit your
requirements. This is achieved using the setup menus. How to configure the EXOTIK is
explained in the rest of this chapter.
Setup menus
The setup menus enable you to configure your EXOTIK for all sources it is connected to,
the loudspeakers in your system and much more. To take advantage of your EXOTIK’s
features, please take the time to configure your unit correctly.
The setup menus are divided into four categories and are accessed via the MAIN MENU:
SSPPEEAAKKEERR SSEETTUUPP
For configuring the unit for the number and size of the loudspeakers in your system and
for calibrating their volume level. (EXOTIK+DA: also for setting the distance of your
loudspeakers from your listening position.)
SSOOUURRCCEE SSEETTUUPP
For configuring sources on the unit.
AAUUDDIIOO SSEETTUUPP
For configuring the audio output of the unit.
GGEENNEERRAALL SSEETTUUPP
For adjusting the general setup of the unit.
There is also a UNIDISK SETUP item in the MAIN MENU for accessing the setup menus
on a Linn UNIDISK player if one is present (see
Using the EXOTIK with a Linn UNIDISK
player
, end of this chapter).
In addition, the EXOTIK features an INSTALLER MENU for saving the configuration of the
unit as set in the above menus and restoring the factory defaults. For full information
see
Installer menu
, this chapter.
Using the setup menus
TToo aacccceessss tthhee sseettuupp mmeennuuss::
Either
●
Press
SSEETTUUPP
on the handset.
or
●
Hold
SSEELLEECCTT
on the front panel until MAIN MENU / SPEAKER SETUP is shown on
the display.
TToo aacccceessss tthhee iinnssttaalllleerr mmeennuu::
●
Hold
SSEETTUUPP
on the handset or
SSEELLEECCTT
on the front panel until INSTALLER MENU
is shown on the display (approximately 5 seconds).
TToo nnaavviiggaattee tthhrroouugghh tthhee mmeennuuss aanndd ooppttiioonnss::
●
Use the
/
keys on the handset or front panel. Arrows on the display indicate
which key(s) can be used.
TToo mmaakkee aa sseelleeccttiioonn::
●
Press
‘‘eenntteerr’’
on the handset, or
SSEELLEECCTT
on the front panel.
TToo eexxiitt ffrroomm tthhee sseettuupp mmeennuuss::
●
Press
SSEETTUUPP
on the handset (if changes have been made you will be prompted to
save or not save the changes).
Setup
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
7
Speaker setup
SIZE
Accesses the SPEAKER SIZE sub-menu.
For all loudspeakers in your system (except a subwoofer) you must inform the
EXOTIK whether the speakers are LARGE or SMALL. These settings refer to the
frequency response of the loudspeakers, not to their physical size.
Standard EXOTIK
For loudspeakers that operate below 100 Hz, select
LLAARRGGEE
.
For loudspeakers that do not operate below 100 Hz, select
SSMMAALLLL
. Frequencies in
the audio signal that are below 100 Hz will be routed to a subwoofer, if present, or
any LARGE loudspeakers, if not.
SMALL FREQUENCY (EXOTIK+DA)
Select the operating frequency that your limited bass response (SMALL)
loudspeakers operate above. Frequencies in the audio signal that are below the
selected option will be routed to a subwoofer, if present, or any full-range
loudspeakers (LARGE), if not.
Options:
4400 HHzz,, 6600 HHzz,, 8800 HHzz,, 110000 HHzz,, 112200 HHzz
Default setting:
8800 HHzz
FRONT*
Large front speakers (full-range frequency response), set to
LLAARRGGEE
.
Small front speakers (limited bass response), set to
SSMMAALLLL
.
Default setting:
LLAARRGGEE
*For two-channel systems, use the FRONT item and set CENTRE, SURROUND and
SURROUND BACK to
NNOONNEE
.
DISTANCE (EXOTIK+DA)
Accesses the SPEAKER DISTANCE sub-menu.
DISTANCE UNITS
Select the units for loudspeaker distance measurements.
Options:
FFEEEETT,, MMEETTRREESS
Default setting:
FFEEEETT
SPEAKER DISTANCE
In order to ensure that sound from all loudspeakers in your system reaches you at
the same time, you must inform the EXOTIK+DA as to the distance each speaker is
from your seating position. The EXOTIK+DA will then add a time delay to the
appropriate speakers.
Set the distance from your seating position for all speakers in your system.
Range:
11 fftt ((00..33 mm)) ttoo 2277 fftt ((88..22 mm))
Default setting:
66 fftt ((11..88 mm))
Select
SSAAVVEE
to save your changes and return to the SPEAKER SETUP menu.
Select
BBAACCKK
to return to the SPEAKER SETUP menu without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
CALIBRATION
Accesses the SPEAKER CALIBRATION sub-menu.
SPEAKER CALIBRATION
If your audio system uses more than two loudspeakers and a subwoofer, you can use
the speaker calibration feature to ensure that the volume level that reaches your
seating position is the same for each loudspeaker (speaker calibration is not
required for two-channel systems). Calibration can be done by ear or by using an
SPL (Sound Pressure Level) meter.
Setup
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
8
CENTRE
Large centre speaker (full-range frequency response), set to
LLAARRGGEE
.
Small centre speaker (limited bass response), set to
SSMMAALLLL
.
No centre speaker, set to
NNOONNEE
.
Default setting:
LLAARRGGEE
SURROUND
Large surround speakers (full-range frequency response), set to
LLAARRGGEE
.
Small surround speakers (limited bass response), set to
SSMMAALLLL
.
No surround speakers, set to
NNOONNEE
.
Default setting:
LLAARRGGEE
SURROUND BACK
Large surround back speakers (full-range frequency response), set to
LLAARRGGEE
.
Small surround back speakers (limited bass response), set to
SSMMAALLLL
.
No surround back speakers, set to
NNOONNEE
.
Default setting:
LLAARRGGEE
SUBWOOFER
If you have connected a subwoofer, set to
YYEESS
.
If you have not connected a subwoofer, set to
NNOO
.
Default setting:
YYEESS
Select
SSAAVVEE
to save your changes and return to the SPEAKER SETUP menu.
Select
BBAACCKK
to return to the SPEAKER SETUP menu without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
There are differences in the method of performing loudspeaker calibration on a standard
EXOTIK and an EXOTIK+DA:
Standard EXOTIK
You will need a test disc that contains a tone signal for each loudspeaker in your system.
Your specialist Linn retailer may be able to supply you with a suitable disc.
TToo ppeerrffoorrmm ssppeeaakkeerr ccaalliibbrraattiioonn::
●
Add a Linn UNIDISK player (or other multi-channel disc playing source) to the
EXOTIK by following the source setup instructions in the next section.
●
Exit setup and change source to the UNIDISK/multi-channel disc playing source.
●
Re-enter setup and return to the SPEAKER CALIBRATION sub-menu.
●
Play the tracks on the test disc for speaker calibration while selecting the
appropriate loudspeakers from the EXOTIK’s menu.
●
If the tone signal coming from a particular loudspeaker is louder or quieter
than from the other loudspeakers, use the
/
keys on the handset to
trim the volume as required.
EXOTIK+DA
TToo ppeerrffoorrmm ssppeeaakkeerr ccaalliibbrraattiioonn::
●
Select
RREEFF.. CCAALLIIBBRRAATTIIOONN LLEEVVEELL
. Adjust the reference calibration level so
that the signal you hear is at a comfortable listening level (or reaches a
preset level on an SPL meter).
●
Select
NNOOIISSEE
. Choose either
WWHHIITTEE
(equal energy per frequency, bright
sounding) or
PPIINNKK
(equal energy per octave, richer in lower frequencies than
White).
●
Select
SSTTAARRTT
. The signal will move round the loudspeakers in your system in
a clockwise direction and will be indicated on the display.
●
When the signal reaches a loudspeaker which is louder or quieter than the
other loudspeakers, use the
/
keys on the handset to trim the volume
as required. A few seconds after the or key has been released the
signal will continue its clockwise direction.
●
To stop loudspeaker calibration, press
SSEETTUUPP
on the handset or
SSEELLEECCTT
on
the front panel.
Range:
--1155 ddBB ttoo 1155 ddBB
(in 0.5 steps)
Default setting:
00 ddBB
Select
SSAAVVEE
to save your changes and return to the SPEAKER SETUP menu.
Select
BBAACCKK
to return to the SPEAKER SETUP menu without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
Select
BBAACCKK
to return to the MAIN MENU.
Select
EEXXIITT
to leave Setup.
Source setup
Select the back panel input you wish to use with your source component, or select ADD
UNIDISK* if you are adding a Linn UNIDISK player as a source component.** You must
complete the source setup procedure for each source component you are connecting to
your EXOTIK.
Options:
AANNAALLOOGG GGRROOUUPP,, AANNAALLOOGG 11 ttoo 66,, SSPPDDIIFF 11 ttoo 33**,, TTOOSS ((TTOOSSLLIINNKK)) 11 ttoo 33**,,
KKNNEEKKTT,, AADDDD UUNNIIDDIISSKK**
*EXOTIK+DA
**If you wish to connect a UNIDISK player to a standard EXOTIK use the ANALOG
GROUP inputs (for multi-channel systems) or a stereo input pair (for two-channel
systems).
Setup
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
9
NAME
You are able to give the source a name which will be shown on the display when that
source is selected.
TToo cchhaannggee tthhee ffllaasshhiinngg cchhaarraacctteerr::
●
Repeatedly press or hold / on the handset or front panel.
The following characters are available: A to Z, 0 to 9, space.
TToo mmoovvee ttoo tthhee nneexxtt oorr pprreevviioouuss cchhaarraacctteerr::
●
Press or .
When you have finished inputting the name, press
‘‘eenntteerr’’
or
SSEELLEECCTT
.
Default setting:
((nnaammee ooff bbaacckk ppaanneell ccoonnnneeccttoorr oorr ‘‘UUNNIIDDIISSKK’’))
Note:
The name can be up to twelve characters long.
TThhee nneexxtt ttwwoo iitteemmss aarree ffoorr uussee iiff AADDDD UUNNIIDDIISSKK hhaass bbeeeenn sseelleecctteedd ffrroomm tthhee ssoouurrccee
sseettuupp ooppttiioonnss.. FFoorr tthhee ootthheerr ssoouurrccee sseettuupp ooppttiioonnss tthheessee iitteemmss wwiillll nnoott bbee sshhoowwnn..
ANALOG INPUT
Select which analogue input(s) is/are connected to the UNIDISK player.
Options:
AANNAALLOOGG GGRROOUUPP,, AANNAALLOOGG 11 ttoo 66
Default setting:
AANNAALLOOGG GGRROOUUPP
DIGITAL INPUT
Select which digital input is connected to the UNIDISK player.
Options:
SSPPDDIIFF 11 ttoo 33,, TTOOSSLLIINNKK 11 ttoo 33
Default setting:
SSPPDDIIFF 11
TYPE
Select a type for this source. This is the type that appears on Linn learning
handsets.
Options:
AAUUXX,, CCDD,, DDVVDD**,, TTUUNNEERR,, PPHHOONNOO 11//LLAASSEERR,, PPHHOONNOO 22//AAUUXX,, TTAAPPEE 11,, TTAAPPEE
22//VVCCRR,, DDAATT,, TTVV,, CCAABBLLEE,, SSAATTEELLLLIITTEE,, NNOONNEE..
Default setting:
AAUUXX
(Except ANALOG 2 and 3, and KNEKT which are set to NONE)
*DVD is the only option available for the ADD UNIDISK source.
Notes:
For ease of use with the handset supplied with the unit, you may wish to restrict the
type selected to either CD, DVD, TUNER or AUX, to allow direct source selection.
If you do not wish to use a particular back panel input, set Type to
NNOONNEE
. This
means that when you are using the
SSOOUURRCCEE --
/
++
keys on the front panel to select a
source, inputs set to NONE will not be seen.
VOLUME OFFSET
Volume offset is for adjusting the volume of a source in comparison to other
sources. You may want to adjust the volume offset for a source if, for example, your
tuner sounds quieter than your CD player when played at the same volume setting.
Range:
--1155 ttoo 1155
(in 0.5 steps). No volume offset equals 0.
Default setting:
00
Setup
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
10
SURROUND CHANNELS
If you are setting up the ANALOG GROUP source or are adding a Linn UNIDISK
player and have a 7.1 speaker configuration, you are able to select whether to use
your side surround or back surround speakers when listening to a 5.1 channel audio
source.
Set to
SSUURRRROOUUNNDD
to send the surround signal to your side surround speakers.
Set to
SSUURRRROOUUNNDD BBAACCKK
to send the surround signal to your back surround
speakers.
Default setting:
SSUURRRROOUUNNDD
Select
SSAAVVEE
to save your changes and return to the SOURCE SETUP menu.
Select
BBAACCKK
to return to the SOURCE SETUP menu without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
Select
BBAACCKK
to return to the MAIN MENU.
Select
EEXXIITT
to leave setup.
Audio setup
VOLUME RATE
Set the speed at which the EXOTIK changes volume when
VVOOLL ++
/
VVOOLL --
is pressed.
Range:
11//1100
(slowest)
ttoo 1100//1100
(fastest)
Default setting:
66//1100
MUTE RATE
Set the speed at which the EXOTIK mutes or unmutes the volume when is pressed, or
when changing sources.
Range:
11//1100
(slowest)
ttoo 1100//1100
(fastest)
Default setting:
66//1100
VOLUME LIMIT
Set the maximum volume level of the EXOTIK.
Range:
00 ttoo 110000
(in 0.5 steps)
Default setting:
110000
VOLUME PRESET
Set the volume level of the EXOTIK when it is brought out of standby.
The setting cannot be higher than the Volume Limit setting (see above).
Range:
00 ttoo 110000
(in 0.5 steps)
Default setting:
4400
MIDNIGHT MOVIE (EXOTIK+DA)
Midnight Movie mode optimises the audio of any source for listening at a reduced
volume.
Midnight Movie mode increases the level of quiet sections (e.g. whispered dialogue in a
movie) and reduces the peaks of loud sections (e.g. action scenes in a movie) but without
restricting the overall dynamics of the original audio signal.
It is turned on/off by pressing and holding
SSUURRRR
on the handset.
Options:
LLOOWW
(least effective)
,, MMEEDDIIUUMM,, HHIIGGHH
(most effective)
Default setting:
LLOOWW
Setup
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
11
DOLBY PRO LOGIC II MUSIC (EXOTIK+DA)
Dolby Pro Logic II is an audio signal processing algorithm that converts a two-channel
audio signal to a five-channel audio signal.
Dolby Pro Logic II Music is a mode of Dolby Pro Logic II that is particularly suited to
music. It features three user-adjustable parameters that are accessed from this item.
CCEENNTTRREE WWIIDDTTHH
This parameter allows adjustment of the audio signal between the centre
loudspeaker and front left and right loudspeakers.
If set to
00
(no spreading) all of the audio signal for the centre channel is sent to the
centre loudspeaker.
If set to
33
(neutral) a portion of the centre channel signal is also sent to the left and
right front loudspeakers.
If set to
77
(Full Phantom) all of the centre channel signal is split evenly between the
front left and right loudspeakers.
Range:
00 ttoo 77
Default setting:
33
PPAANNOORRAAMMAA CCOONNTTRROOLL
If set to
OONN
, the Panorama control extends the audio signal from the front left and
right loudspeakers to include the surround left and right loudspeakers. This adds a
"wraparound" effect to the sound.
Options:
OONN,, OOFFFF
Default setting:
OOFFFF
DDIIMMEENNSSIIOONN CCOONNTTRROOLL
This parameter allows you to shift the balance between the front and rear
loudspeakers. Positive values move the sound towards the front, negative values
towards the rear.
If a recording is too spacious or strong from the surround loudspeakers it can be
shifted "forward" to get a better balance. A stereo recording can be shifted
"backward" to make the sound more enveloping.
Range:
--33
(most rear)
ttoo 33
(most front)
Default setting:
00
(neutral)
Select
SSAAVVEE
to save your changes and return to the AUDIO OPTIONS menu.
Select
BBAACCKK
to return to the AUDIO OPTIONS menu without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
Select
SSAAVVEE
to save your changes and return to the MAIN MENU.
Select
BBAACCKK
to return to the MAIN MENU without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been selected,
you will be prompted to save or not save the changes).
General setup
DISPLAY INTENSITY
Set the brightness of the front panel display.
Options:
LLOOWW,, MMEEDDIIUUMM,, HHIIGGHH
Default setting:
MMEEDDIIUUMM
DISPLAY CONTENT
Set what information you want displayed on the unit’s front panel when it is in normal
operation.
Options:
LLAASSTT UUSSEEDD
(source or volume), (current)
SSOOUURRCCEE AANNDD VVOOLLUUMMEE,, VVOOLLUUMMEE,,
(current)
SSOOUURRCCEE
Default setting:
SSOOUURRCCEE AANNDD VVOOLLUUMMEE
Setup
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
12
Setup
DISPLAY TIMEOUT
Set the time that new volume or source information is shown for before unit returns to
its Display Content (see above).
Range:
11 SSEECC.. ttoo 1100 SSEECC..
Default setting:
44 SSEECC..
SELECTION TIMEOUT
When the source is changed, this item sets the time the EXOTIK takes before the new
source is selected.
Range:
11 SSEECC.. ttoo 1100 SSEECC..
Default setting:
44 SSEECC..
SLEEP TIMEOUT
Set the time elapsed before the front panel display enters sleep mode (i.e. shows three
dots) after a key on the front panel or handset is pressed.
Options:
NNEEVVEERR SSLLEEEEPP,, IIMMMMEEDDIIAATTEE,, 3300 SSEECC..,, 55 MMIINNSS..
Default setting:
NNEEVVEERR SSLLEEEEPP
STARTUP SOURCE
Set the source the unit selects when brought out of standby.
Options:
LLAASSTT UUSSEEDD,, NNOONNEE,, ((aannyy ooff tthhee ssoouurrccee iinnppuuttss))
Default setting:
LLAASSTT UUSSEEDD
STANDBY RECORD FROM
You can record from a source component to a recording device through the EXOTIK,
even if the EXOTIK is in standby mode.
Set which source configuration you want the EXOTIK to select when it is in standby.
Options:
LLAASSTT UUSSEEDD,, NNOONNEE,, ((aannyy ooff tthhee ssoouurrccee iinnppuuttss)),, AASS KKNNEEKKTT**
Default setting:
LLAASSTT UUSSEEDD
KNEKT
If your EXOTIK is installed in a Linn KNEKT multi-room system, select the appropriate
setting. If your EXOTIK is not installed in a KNEKT system, select
NNOONNEE
.
Options:
NNOONNEE,, MMAAIINN RROOOOMM,, LLOOCCAALL RROOOOMM,, IINNTTEERRSSEEKKTT
Default setting:
NNOONNEE
ACCESSORY SOCKET
Define the use of the accessory (ACC/RCU) socket on the back panel.
Options:
RRCCUU**
(KNEKT Room Control Unit)
,, IIRR
(Infrared Repeater)
Default setting:
RRCCUU
PRODUCT IR
Enable or disable the infrared receiver on the front of the unit.
Options:
EENNAABBLLEE,, DDIISSAABBLLEE
Default setting:
EENNAABBLLEE
*For use with Linn KNEKT systems.
13
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
SSTTOOPP BBIITTSS
Set the stop bits to suit the RS232 protocol being used.
Options:
11,, 22
Default setting:
11
Select
SSAAVVEE
to save your changes and return to the GENERAL SETUP menu.
Select
BBAACCKK
to return to the GENERAL SETUP menu without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
Select
SSAAVVEE
to save your changes and return to the MAIN MENU.
Select
BBAACCKK
to return to the MAIN MENU without saving changes.
Select
EEXXIITT
to leave setup (if changes have been made and SAVE has not been selected,
you will be prompted to save or not save the changes).
RS232 EVENTS
If set to
EENNAABBLLEE
, the unit passes information regarding its internal status to an external
device that accepts RS232 data.
Options:
EENNAABBLLEE,, DDIISSAABBLLEE
Default setting:
DDIISSAABBLLEE
RS232 Setup
Accesses the RS232 SETUP sub-menu.
The RS232 Setup sub-menu is for use if the EXOTIK is communicating with other RS232
enabled products (e.g. a third-party controller).
BAUD RATE
Set the baud rate to suit the RS232 protocol being used.
Range:
11220000 ttoo 223300440000
(11 settings)
Default setting:
99660000
PARITY
Set parity to suit the RS232 protocol being used.
Options:
EEVVEENN,, OODDDD
Default setting:
EEVVEENN
DATA BITS
Set the data bits to suit the RS232 protocol being used.
Options:
77,, 88
Default setting:
77
Setup
EXOTIK PRE-AMPLIFIER
Owner’s Manual
English
14
Installer menu
TToo aacccceessss tthhee IInnssttaalllleerr mmeennuu::
●
Hold
SSEETTUUPP
on the handset or
SSEELLEECCTT
on the front panel until INSTALLER MENU
is shown on the display (approximately 5 seconds).
SAVE AS INSTALLER
After the EXOTIK has been set up you can save the settings by selecting this item. The
saved Installer configuration can be restored at any time should the EXOTIK’s setup be
changed (see below). Any alterations to the product’s setup that you wish to keep as a
new Installer configuration can be stored by selecting this item, which will overwrite the
existing Installer configuration.
RESTORE INSTALLER
If you have made changes to the setup of the EXOTIK that you do not wish to keep, use
this option to restore the Installer configuration.
RESTORE FACTORY
Use this option to restore the default settings for all the setup menus.
SOFTWARE REVISION
This item informs the installer as to the version of the software installed on the EXOTIK.
Select
EEXXIITT
to leave the Installer menu (if changes have been made you will be
prompted to save or not save the changes).
Setup
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual
15
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
