Albatron KM51PV-754 User manual

Brand: Albatron

Model: KM51PV-754

Category: Motherboards

Type: User manual

KM51PV-754

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system or translated into any language or computer language, in any form

or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise,

without the prior written permission of the company. Brands and product names are trademarks

or registered trademarks of their respective companies.

The vendor makes no representations or warranties with respect to the contents herein and

especially disclaim any implied warranties of merchantability or fitness for any purpose. Further

the vendor reserves the right to revise this publication and to make changes to the contents

herein without obligation to notify any party beforehand. Duplication of this publication, in part or

in whole, is not allowed without first obtaining the vendor’s approval in writing.

Trademark

All the trademarks or brands in this document are registered by their respective owner.

Disclaimer

We make no warranty of any kind with regard to the content of this user’s manual. The content

is subject to change without notice and we will not be responsible for any mistakes found in this

user’s manual. All the brand and product names are trademarks of their respective companies.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense. However, there is no guarantee that

interference will not occur in a particular installation.

CE Mark

The device is in accordance with 89/336 ECC-ENC Directive.

Ver: EG100

Downloaded from www.Manualslib.com manuals search engine

KM51PV-754

nVIDIA

nForce4 C51PV & MCP51

Supports Socket 754

AMD

Athlon

64/ Sempron

Processor

User’s Manual

Dimensions (Micro-ATX Form-Factor):

z 220mm x 244mm ( W x L )

Operating System:

z Windows® 2000/ XP

Downloaded from www.Manualslib.com manuals search engine

Things You Should Know

0 The images and pictures in this manual are for reference only and may vary from the

product you received depending on specific hardware models, third party components

and software versions.

0 This mainboard contains very delicate IC chips. Always use a grounded wrist strap

when working with the system.

0 Do not touch any IC chip, lead, connector or other components.

0 Always unplug the AC power when you install or remove any device on the mainboard

or when confuguring pins and switches.

Packing List

 KM51PV-754 mainboard

 Mainboard User’s Manual CD

 I/O Bracket

 Mainboard Setup Driver CD

 Mainboard Quick Installation Guide

 HDD Cable

 SATA Cable

 FDD Cable

 SATA Power Cord (Optional)

 TV OUT Cable (Optional)

 SPDIF Card (Optional)

 ABS Card (Optional)

Symbols

The following list explains the convention for symbols that will be used throughout this

manual:

Attention- Im

ortant Information

Follow the procedures below…

Troubleshooting Tips

Refer to other sections in this manual…

Downloaded from www.Manualslib.com manuals search engine

Table of Contents

CHAPTER 1. GETTING STARTED ....................................................1

INTRODUCTION.......................................................................................................1

SPECIFICATION .......................................................................................................2

CONFIGURATION ....................................................................................................5

Layout of KM51PV-754..................................................................................5

HARDWARE INSTALLATION ...................................................................................6

CPU Processor Installation..............................................................................6

Memory Installation ........................................................................................7

Back Panel Configuration................................................................................8

Connectors.....................................................................................................10

Front Panel Headers.......................................................................................11

Headers & Jumpers........................................................................................12

Audio Configuration......................................................................................15

Slots...............................................................................................................16

Power Supply Attachments............................................................................17

CHAPTER 2. BIOS SETUP........................................................... 18

INTRODUCTION.....................................................................................................18

KEY FUNCTION.....................................................................................................18

MAIN MENU .........................................................................................................19

ADVANCED BIOS FEATURES..............................................................................21

INTEGRATED PERIPHERALS................................................................................27

POWER MANAGEMENT........................................................................................30

HARDWARE MONITOR.........................................................................................32

LOAD DEFAULTS/EXIT MENU..............................................................................32

CHAPTER 3: SOFTWARE SETUP................................................... 33

SOFTWARE LIST ...................................................................................................33

SOFTWARE INSTALLATION...................................................................................33

CHAPTER 4: TROUBLESHOOTING................................................. 35

APPENDIX I: SUPER 5.1 CHANNEL AUDIO EFFECT SETUP....................................38

APPENDIX II: RAID SETUP...................................................................................39

APPENDIX III: ABS (ALBATRON BIOS SECURITY) CARD SETUP ........................46

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Chapter 1. Getting Started

Introduction

Congratulations on the choosing the KM51PV-754 Mainboard. It is based on the nVIDIA

nForce4 C51PV Northbridge chipset and the nVIDIA

nForce4 MCP51 Southbridge chipset;

with possessing integrated graphics feature. The mainboard supports the AMD Athlon

64/

Sempron

processor socket 754 with FSB (Front Side Bus) frequencies of 800 MHz (1600

MT/s).

The KM51PV-754 provides two DIMM (Dual In-Line Memory Modules) sockets. It allows you

installing 184-pin, non-ECC, and unbuffered DDR400 (PC3200)/ DDR333 (2700)/ DDR266

(PC2100) SDRAMs and also supports a total memory capacity of 2GB.

The mainboard provides one PCI-E x16 slot, one PCI-E x1 slot and two PCI slots for use with a

graphics card or expansion cards which the interfaces are compatible.

The KM51PV-754 provides one floppy disk drive connector that can be used with 360KB/

720KB/1.2MB/1.44MB/2.88MB drives. It also has two IDE connectors for hard drives supporting

Ultra ATA 66/100/133. In addition, the onboard Serial ATA II comes with four SATA II

connectors, which each interface can provide up to300 Mbps transmission speeds and also

support RAID 0/ 1/ 0+1/ JBOD/ 5 mode (See Appendix II).

Moreover, the KM51PV-754 provides onboard I/O facilities such as one VGA connector

(=D-Sub connector), one DVI connector, and a maximum of eight USB 2.0/ 1.1 ports that can be

set. Three headers are also available on this mainboard for a TV OUT connector, a printer

connector, and a COM connector to be set externally with cables and used additionally.

The onboard AC’ 97 audio codec supports high quality 6/4/2-channel audio play (Super 5.1

Channel Audio Effect) (See Appendix I) and supports the Sony/Philips Digital Interfaces

(SPDIF) specifications.

This mainboard also comes with an onboard 10/100 Mbps Ethernet LAN chip. There is a LAN

port on the case back panel that you can directly plug into an Internet cable.

In addition, this mainboard supports the ABS (Albatron BIOS Security) card (Optional), which is

a small circuit board inserted onto the mainboard providing full backup BIOS functionality in

case of BIOS failure or damage during the BIOS flash (See Appendix III).

All the information (including hardware installation and software installation) in this manual are

for reference only. The contents in this manual may be updated without notice. The company

will not assume any responsibility for any errors or mistakes within.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Specification

CPU:

z Supports Socket 754

z Supports AMD Athlon

64/ Sempron

Processor

z Supports Hyper-Transport

Link Technology

z Supports 800 MHz (1600MT/s) FSB (Front Side Bus) Frequencies

Chipset:

z Northbridge Chipset – nVIDIA

nForce4 C51PV ( nVIDIA

GeForce

6150)

－ Integrated nVIDIA

Pure Video

Technology

－ Supports TV Encoder

－ Supports 475 MHz Graphic Clock

－ Supports MPEG-2 (DVD)/ WMV9 (HD-Video) Playback

－ Supports Video Scaling

z Southbridge Chipset – nVIDIA

nForce4 MCP51 ( nVIDIA

nGorce 430)

z I/O Controller – Winbond

W83627HF-AW

z AC’ 97 Aduio Codec – Realtek

ALC655

z LAN PHY Controller – Broadcom

AC 131

Memory:

z Two DIMM sockets with Dual Channel Technology supported, and also support a

total memory capacity of 2GB

z Supports to use 184-pin, non-ECC, and unbuffered DDR400 (PC3200)/ DDR333

(PC2700)/ DDR266 (PC2100) SDRAMs

Slots:

z One PCI-E x16 slot

z One PCI-E x1 slot

z Two PCI slots

FDD Connector:

z One floppy disk drive connector, supports up to two FDDs can be set

z Supports 360KB/720KB/1.2MB/1.44MB/2.88MB

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

IDE Connector:

z Two IDE connectors, support up to four IDE devices can be set

z Supports Ultra ATA 33/66/100/133

z Supports high capacity hard disk drives

Serial ATA II Connector:

z Four SATA II connectors, support up to four SATA II HDDs can be set

z Supports SATA 2.0 specification and provides 300 Mbps transmission speeds

z Supports RAID 0/1/ 0+1/ JBOD/ 5 mode

Onboard I/O facilities:

z One PS/2 mouse port and one PS/2 keyboard port

z One DVI connector

z One VGA connector (=D-Sub connector)

z Three onboard headers are available to set a TV Out connector, a Printer connector,

and a COM connector with cables externally

Onboard USB Ports:

z Six onboard USB 2.0/ 1.1 ports

z One front USB header comes with this mainboard, and supports a maximum of two

additional USB ports can be set

Onboard AC’ 97 Audio Codec:

z High performance Codec with high S/N ratio (>90 db)

z Compliant with AC’ 97 2.3 specification

z Support 6/4/2-channel playback capability (Super 5.1 Channel Audio Effect)

z Support 3D stereo enhancement

z Support Sony/ Philips Digital Interfaces (S/PDIF) functionality

Onboard LAN Chip:

z Supports 10/100 Mbps Ethernet LAN

z Supports nVIDIA

Active Armor

, it provides advanced data packet inspection

z Supports nVIDIA

Firewall

, it protects your system from intruders

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

BIOS:

z Phoenix-Award™ BIOS

z Supports APM1.2

z Supports ACPI2.0 power management

Green Function:

z Supports Phoenix-Award™ BIOS power management function

z Supports system-wake-from-power-saving-mode by keyboard or mouse touching

Shadow RAM:

z The onboard memory controller provides the shadow RAM functionality and ROM

BIOS functionality

Flash Memory:

z Supports flash memory functionality

z Supports ESCD funtionality

Hardware Monitor Function:

z Monitors CPU/ Chassis Fan Speed

z Monitors CPU and system temperatures

z Monitors system voltages

Watch Dog Timer:

z This function is used for detecting the system hangs during the POST stage due to

conflicts resulting from changing the system BIOS settings. Once the problem is

detected, the system will reset the configurations and reboot the system within five

seconds.

ABS (Albatron BIOS Security):

z Supports ABS Card (Optional)

z Supports BIOS backup

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Configuration

Layout of KM51PV-754

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Hardware Installation

This section will assist you in quickly installing your system hardware. Wear a wrist ground strap

before handling components. Electrostatic discharge may damage your system components.

CPU Processor Installation

This mainboard supports AMD Athlon

64/ Sempron

processor using Socket 754. Before

building your system, we suggest you visit the AMD website and review the processor

installation procedures. http://www.amd.com

CPU Socket 754 Configuration Steps:

1. Locate the CPU socket on your mainboard and nudge the locking lever away from the socket.

Then lift the lever to a 90-degree angle.

2. On the socket, locate the corner which has the “diagonally cut-corner” on the rectangular

shaped pattern of pinholes (see diagram below-left). Match that corner with the “gold triangle”

on the CPU (see diagram below-right) and lower the CPU onto the socket. The bottom of the

CPU should be flush with the face of the socket.

Diagonally

Cut-corner

Gold triangle

3. Lower the lever until it snaps back into position. This will lock down the CPU.

4. Smear thermal grease on top of the CPU. Lower the CPU fan onto the CPU and use the

clasps on the fan to attach it to the socket. Finally, extend the power cable from the fan and

insert it onto the “CPUFAN” adapter.

Attention

DO NOT touch the CPU pins in case they are damaged. Also, make sure

that you have completed all installation steps before powered on the

system. Finally, double-check that the cooling fan is properly installed

and the CPU fan power cord is securely attached, in case your CPU and

other sensitive components are damaged because of high temperatures.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

FAN Headers: CPUFAN, AUXFAN, CHASFAN

There are three fan headers available for cooling fans. The cooling fans play an important role

in maintaining ambient temperatures in your system. The CPUFAN header is attached with a

CPU cooling fan. The CHASFAN and AUXFAN headers are attached with other cooling fans.

Pin Assignment

1 Ground

2 Power (+12V)

CPUFAN/ AUXFAN/

CHASFAN

3 FAN RPM rate sense

On most fan power cord, the black wire of the fan cable is the “ground”

and should be attached to pin-1 of the header.

Attention

You can avoid damaging your CPU due to high temperatures with

proper cooling equipment. It is recommended that attach a cooling fan

on top of your CPU. Use the CPUFAN header to attach the fan cord.

Memory Installation: DIMM1/2

The KM51PV-754 provides two DIMM (Dual In-Line Memory Modules) sockets. It allows you to

install 184-pin, non-ECC, and unbuffered DDR400(PC3200)/ DDR333(2700)/ DDR266(PC2100)

SDRAMs, and supports to install a total memory capacity of 2GB.

Memory Setup Steps:

The following instructions explain how to set memories onto the DIMM sockets for this

mainboard.

1. Pull the white plastic tabs at both ends of the socket away.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

2. Align a memory on the socket such that the notch on the memory matches the break on the

socket.

3. Lower the memory vertically into the socket and press firmly by using both thumbs until the

memory snaps into place.

4. Repeat steps 1, 2 & 3 for the remaining memory and DIMM sockets setup.

Back Panel Configuration

PS/2 Mouse & PS/2 Keyboard Ports: KB/MS

This mainboard provides a standard PS/2 mouse port and a PS/2 keyboard port. The pin

assignments are described below.

Pin Assignment Pin Assignment

Data

+5 V (fused)

N/A

Clock

Ground

N/A

PS/2 Mouse

PS/2 Keyboard

* The pictures shown above are for reference only. The actual

installation may vary depending on models.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

DVI & VGA Connectors: DVI, VGA

The mainboard provides one DVI connector and one VGA

connector on the case back panel.

DVI connector delivers the digital signals, and is able to

connect with LCD display, plasma display, or other display

device which with the DVI interface compatible.

VGA connector (= D-Sub connector) delivers the analogy

signals, and is able to connect with traditional CRT display,

flat display, or other display device which with the D-Sub

interface compatible.

USB & LAN Ports: USB1, USB2, USB/LAN

There are six onboard USB 2.0/ 1.1 ports on the back panel. These USB ports are used to

attach with USB devices, such as keyboard, mice and other USB supported devices. There is

also a 10/100 Mbps Ethernet LAN port available for you to attach an Internet cable.

Pin Assignment Pin Assignment

TX+ (TX+)

NC (TRD2-)

TX- (TX-)

RX- (RX-)

RX+ (RX+)

NC (TRD3+)

NC (TRD2+)

NC (TRD3-)

Assignment Pin Assignment

1/5

+5 V (fused)

3/7

USBP0+/P1+

2/6

USBP0-/P1-

4/8

Ground

Audio Ports: Sound

This mainboard provides three audio ports, the Mic-in, Line-in and

Line-out. These are the standard audio ports that provide basic audio

function.

Line-In (Blue)

This port is for audio input and connects to external audio devices such

as CD player, tape player, etc. When the Super 5.1 Channel Audio

Effect is enabled, this port will output audio for the rear speakers.

Line-Out (Green)

This port is an output audio port used for connecting to speakers or a

headset. When the Super 5.1 Channel Audio Effect is enabled, this port will output audio for the

front speakers.

Mic-In (Pink)

This port is for connecting to a microphone. When the Super 5.1 Channel Audio Effect is

enabled, this port will output audio for your subwoofer/center speakers.

This mainboard supports Super 5.1 Channel Audio Effect which allows you to

transform your 2 speaker audio system into a 6/4 speaker audio system. See

Appendix I for more information.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Connectors

Floppy Disk Drive Connector: FDC

The mainboard provides a standard floppy disk drive connector (FDC) that supports 360KB/

720KB/1.2MB/1.44MB/2.88MB floppy disk drives using a FDD ribbon cable.

Hard disk drive Connectors:

The mainboard provides two IDE connectors that support Ultra ATA 66/100/133 IDE devices.

You can attach a maximum of four IDE devices, such as hard disk drive (HDD), CD-ROM,

DVD-ROM, etc. using IDE ribbon cables.

rimary IDE Connector: IDE1

In general, two IDE devices can be attached onto one IDE connector. If you attach two IDE

HDDs, you must configure one drive as the master and the other one as the slave.

econdary IDE Connector: IDE2

The IDE2 connector can also be attached with two IDE HDDs, and remember to configure one

drive as the Master and the other one as the Slave as well. In addition, it is recommended that

attach the optical devices such as CD-ROM, DVD-ROM, etc. onto this IDE2 connector.

SATA II Connector: SATA1/ SATA2/ SATA3/ SATA4

The four SATA II connectors support 300 Mbps transmission speeds and RAID 0/1/ 0+1/ JBOD/

5 mode. One SATA connector only can attach one SATA HDD of each time using SATA cables.

Pin Assignment Pin Assignment

1 Ground 2 TX+

3 TX- 4 Ground

5 RX- 6 RX+

SATA1~4

7 Ground

This mainboard supports RAID 0/1

0+1/JBOD/5 mode, refe

Appendix II for more information.

Attention

The FDD/IDE cable is designed and should be attached with a

specific direction. One edge of the cable will usually in color such

as red, to indicate that should line up with the header pin-1.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Front Panel Headers: FPSWLED1, SPEAKER

FPSWLED1

Pin Assignment

Function

Pin Assignment

Function

1 HDD LED (+) 2 Power LED (+)

3 HDD LED (-)

Hard Drive LED

(HD_LED)

4 Power LED (-)

Power LED

(ACPI_LED)

5 Reset Control (-) 6 Power Switch (+)

7 Reset Control (+)

Reset Switch

(RST_SW)

8 Power Switch (-)

Power-on Switch

(PWR_SW)

9 N/C 10 N/C

Har

Res

Pow

Spe

d Drive LED Header (Red): HD_LED

If your case front panel has a hard drive LED cable, attach it to this header. The LED will flicker

when there is hard disk drive activity.

et Switch Header (Blue): RST_SW

This header can be attached to a momentary SPST switch (reset button) cable on your case

front panel. The switch is normally left open. When the switch closed, it will cause the

mainboard to reset and run the POST (Power-On Self Test).

er-on Switch Header (Orange): PWR_SW

This header can be attached to a power switch cable on your case front panel. You can turn

your system on or off by pressing the button attached to this power switch cable.

er LED Header (Green): ACPI_LED

Attach the power LED cord from the case front panel onto this header, then the power LED will

illuminate while the system is powered on.

aker Header (Purple): SPEAKER

A speaker cable on your case front panel can be attached to this header. When you reboot the

computer, this speaker will issue a short audible (beep). If there are problems during the Power

On Self-Test, the system will issue an irregular pattern of audible beeps through this speaker.

Pin Assignment Pin Assignment

1 PC_BEEP 2 N/C

SPEAKER

3 Ground 4 +5V

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Headers & Jumpers

Front USB Header: USB3

This mainboard provides six onboard USB 1.1/2.0 ports (back panel) that attach to USB devices.

There is one additional USB header that can be connected by a cable to two more USB ports on

your case front panel giving you a possible 8 USB ports.

Pin Assignment Pin Assignment

1 +5V (fused) 2 +5V (fused)

3 USB- 4 USB-

5 USB+ 6 USB+

7 Ground 8 Ground

USB3

9 Key 10 N/A

Attention

If you are using a USB 2.0 device with Windows 2000/XP, you will

need to install the USB 2.0 driver from the Microsoft

website. If you

are using Service pack 1 (or later) for Windows

XP, and using

Service pack4 (or later) for Windows® 2000, you will not have to install

the driver.

TV OUT Header: TV_OUT

Attach the TV OUT cable (Optional) which the product provided onto this header. Then through

attaching the cable of TV devices onto the S-Video connector of TV out cable, the TV is able to

use as a monitor display.

TV_OUT

Pin Assignment Pin Assignment

1 Ground 2 Key

3 PB OUT 4 C OUT

5 Y OUT

S-Video Connector

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Serial Interface Header: CONN_COM1

This mainboard provides a CONN_COM1 header for you connecting an external serial

connector on your case back panel. Attach the serial connector cable (Optional) onto this

header, then you can use this serial connector to attach with a mic, modem or other peripheral

device.

Pin Assignment Pin Assignment

1 +12V 2 +5V

3 -12V 4 Key

5 DCD0- 6 SIN0

7 SOUT0 8 DTR0-

9 Ground 10 DSR0-

11 RTS0- 12 CTS0-

CONN_COM1

13 RI0- 14 RI-

Printer Interface Header: PRT

This mainboard provides a PRT header for you connecting an external printer connector on

your case back panel. Attach the printer connector cable (Optional) onto this header, then you

can use this printer connector to attach with a printer.

Pin Assignment Pin Assignment

1 RSTB- 2 RPDR0

3 RPDR1 4 RPDR2

5 RPDR3 6 RPDR4

7 RPDR5 8 RPDR6

9 RPDR7 10 ACK-

11 BUSY 12 PE

13 SLCT 14 RAFD-

15 ERR- 16 RINIT_P-

17 RSLIN- 18 Ground

19 Ground 20 Ground

21 Ground 22 Ground

23 Ground 24 Ground

PRT

25 Ground 26 Key

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

The following steps explain how to reset your CMOS

configurations when you forgot a system password.

USB Power Selection Header: JP3

USB devices attached to the back panel USB ports can awaken the system from sleep mode.

In order to enable this functionality, you must adjust the jumper caps on JP3 header for +5V or

+5VSB mode depending on which USB port that the USB device is attached to.

JP3 Assignment Assignment

Pin 1-2 Close

+5V

S1 sleep mode (CPU stopped, DRAM

refreshed, system running in low power

mode)

Pin 2-3 Close

+5VSB

S3/S4/S5 sleep modes (no power to

CPU, DRAM in slow refresh, power

supply in reduced power mode)

Note: Close stands for putting a jumper cap onto two header pins.

Clear CMOS Jumper: JP1

The “Clear CMOS” function is used when you are unable boot your system and need to reset

the BIOS settings (CMOS settings) back to the manufacturer’s original settings. This is also a

way to reset the system password if you have forgotten it.

JP1 Assignment

Pin 1-2 Close

Normal (Defult)

Pin 2-3 Close

Clear CMOS Data

Note: Close stands for putting a jumper cap onto two header pins.

1. Turn off your system and disconnect the AC power cable.

2. Set JP1 header to OFF (2-3 Closed).

3. Wait several seconds.

4. Set JP1 header to ON (1-2 closed).

5. Connect the AC power cable and turn on your system.

6. Reset your new password.

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Audio Configuration

CD-ROM Audio-In Connector: CD-IN

The CD-IN connector is used to attach an audio cable to audio devices such as CD-ROMs,

DVD-ROMs etc.

Pin Assignment

1 Left channel input

2 Ground

3 Ground

CD-IN

4 Right channel input

SPDIF Header: SPDIF

S/PDIF is a recent audio transfer file format, which provides high quality audio using optical fiber

and digital signals. This mainboard is capable to deliver audio output and receive audio input

through a SPDIF Card (optional) with this header attached. You can just simply set the SPDIF

Card on your case back panel, and attach the SPDIF cord and FRONT AUDIO cord onto

specific headers on the mainboard. The RCA or TOS-Link connectors will be provided on the

SPDIF Card and which are convenient you to output or input audio format files between your

system and the SPDIF styled devices.

SPDIF

Pin Assignment Pin Assignment

1 +5V 2 Key

3 SPDIF out 4 Ground

5 SPDIF in

Downloaded from www.Manualslib.com manuals search engine

Mainboard KM51PV-754

Front Audio Connector: FRONT AUDIO

If your case front panel has audio ports, you can connect them to the Front Audio Header of this

mainboard. First, you must remove the jumper caps on this header and then attach the cables

from the front panel to the pins on this header. You can use both the front audio panel and back

panel audio simultaneously. If you are not using front panel audio ports, leave the jumper caps

on the header pins (Note: pins 5&6 and 9&10) to avoid problems with the back panel audio

ports.

FRONT AUDIO

Pin Assignment Pin Assignment

1 Mic in/center 2 Ground

3 Mic_VREF 4 Audio power +5V

5 Front out_R 6 Rear out_R

7 N/C 8 Key

9 Front out_L 10 Rear out_L

Slots

PCI-Express x16 Slot: PCIE1

This mainboard is able to install a graphics card which the PCI-Express x16 interface

compatible to this PCIE1 slot.

PCI-Express x1 Slot: PCIE2

This mainboard is able to install an expansion card which the PCI-Express x1 interface

compatible such as network card, SCSI card, etc. to this PCIE2 slot.

PCI Slots: PCI1, PCI2

PCI stands for Peripheral Component Interconnect and is a bus standard for installing

expansion cards such as network card, SCSI card, etc. to these PCI slots.

Downloaded from www.Manualslib.com manuals search engine

Page is loading ...

Albatron KM51PV-754 User manual

Brand: Albatron

Model: KM51PV-754

Category: Motherboards

Type: User manual

Download PDF

report

Albatron KM51PV-754 User manual

Albatron KM51PV-754 User manual

Related papers

Other documents