Audiovox FRS122-2 User manual

Brand: Audiovox

Model: FRS122-2

Category: Two-way radios

Type: User manual

128-6675

1 of 24

FAMILY RADIO SERVICE (FRS)

Model

FRS122-2

Released: 3-10-03

OwnerOwner

Owner

’s Man’s Man

’s Man

ualual

ual

MODE

LOHI

128-6675

2 of 24

NEVER ATTEMPT TO CHARGE ALKALINE OR DRY CELL BATTERIES, AS

BATTERIES MAY BURST CAUSING PERSONAL INJURY AND DAMAGE

TO THE PRODUCT. WHEN RECHARGING NICKEL METAL HYDRIDE (Ni-

MH) BATTERIES WITH THE SUPPLIED AUDIOVOX CHARGER AND WALL

ADAPTER, USE ONLY AUDIOVOX-APPROVED RECHARGEABLE BATTER-

IES. USE OF THE AUDIOVOX CHARGER WITH OTHER BRANDS OF BAT-

TERIES IS NOT RECOMMENDED, AS BATTERY CHARGING TIMES WILL

VARY WITH DIFFERENT BRANDS. REFER TO THE MANUFACTURER’S

INSTRUCTIONS FOR CHARGING OTHER BRANDS OF BATTERIES.

AVOID PLACING THE FRS122-2 RADIO TRANSCEIVER FOR PRO-

LONGED PERIODS OF TIME IN DIRECT SUNLIGHT OR TEMPERATURES

BELOW -4° F (-20° C) OR ABOVE 140 ° F (60° C).

KEEP THE ANTENNA AT 1 INCH (2.5 cm) AWAY FROM YOUR HEAD AND

BODY. DO NOT USE YOUR FRS122-2 RADIO TRANSCEIVER WITH A

DAMAGED ANTENNA.

PLACE THE RUBBER COVERS ON JACKS WHEN NOT IN USE.

SAFETY INFORMATION

Operation is subject to the following two conditions : (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

CAUTION

128-6675

3 of 24

1. Battery Cover

2. Monitor (M) Button

3. Detachable Carry Clip

4. Push-To-Talk (PTT) and Func-

tion Confirmation Button

5. Antenna

6. External Speaker (SP)/

Microphone (MIC)/CHG Jack

7. Built-in Speaker

Model FRS122-2

8. Liquid Crystal Display (LCD)

9. Built-in Microphone

10. Up Channel/Volume Button

11. Down Channel/Volume

Button

12. MODE/VOX Button

13. Power On/Off and SCAN

Button

14. Battery Charging Contacts

(REF)

MODE

PTT

M

LOHI

PTT

M

128-6675

4 of 24

Model FRS122-2 DISPLAY

1.Roger Beep Tone Indicator: This icon appears when the Roger Beep

tone is on, and disapppears when the tone is not in use.

2.Transmit Indicator: Icon appears when the unit is in the transmit

mode (PTT button activated or VOX mode active).

3.Busy Indicator: This icon appears when the unit is receiving a

transmission.

4. Large Segment Display: Indicates the channel number in use between

1 and 14.

5.Scan Indicator: This function allows the user to scan a chanel every

0.5 second to search for a valid signal.

6.HI/LO Indicators: Appropriate icon appears when the transmit power

is set to desired output power.

7.Battery Level Indicator: Icon appears flashing to indicate low

battery charge level.

8.Small Segment Display: Indicates the CTCSS tone code (1-38)

function is active for the main channel in use.

9.Monitor Indicator: This function is not used.

10.Key Lock Indicator: This function is not used.

11.Voice Activated Transmission (VOX) Indicator: This function allows

hands-free conversation. The icon appears when the VOX mode is

activated.

LOHI

128-6675

5 of 24

Equipment and Accessories Supplied

1. Radio (2) FRS122-2

2. Owner’s Manual (1) 128-6675

Optional Accessories

1. Rechargeable Batteries (4) NiMH, P/N GMRS1222BAT

2. Boom Microphone/Headset GMRSBHST4

3. Dual Desk-Top Charger GMRS1222DS

4. AC Wall Adapter GMRS1222AC

5. Vehicle Cigarette Lighter Adapter GMRS1502CG

6. Leather Carrying Case GMRS1502LC

Powering the transceiver:

Your FRS122-2 radio transceiver operates on four AAA batteries. Alkaline

batteries will provide slightly better performance than rechargeable

batteries. Only Audiovox-approved rechargeable batteries (optional) can

be recharged in the radio transceiver using the optional charging

accessories. This will ensure optimum performance for the FRS122-2.

Battery charging time is typically 10-12 hours. Use of the optional Audiovox

charging equipment with other brands of rechargeable batteries is not

recommended as battery charging times will vary. Refer to the

manufacturer’s instructions for charging other brands of batteries.

Batteries

There are three methods of powering the FRS122-2:

1.Alkaline Batteries.

WARNING: Do not attempt to recharge Alkaline batteries.

2.Audiovox Rechargeable Ni-MH Batteries - (Rechargeable Bat-

teries, Wall Adapter, Charging Stand and Cigarette Lighter

Adapter can be purchased separately).

Use only Audiovox-approved rechargeable batteries and optional

charging equipment when charging batteries internal to the unit.

NOTE: To extend battery life, avoid overcharging the batteries.

128-6675

6 of 24

3. Various Brands of Rechargeable Batteries - Use of the

Audiovox charger with other brands of rechargeable batteries is not

recommended, as battery charging times will vary with different

brands of batteries.Refer to the manufacturer’s instructions for

charging other brands of batteries.

Installing the batteries:

Battery installation is made more convenient when the carry clip is either

rotated left or right to the horizontal position, or is removed. Simply rotate

the clip in either direction to the horizontal position. Be careful not to use

excessive force. To remove the clip, press down on the spring release tab

and pull the clip straight out from the radio body. Next, press down with the

thumb at the embossed arrow, slide the battery cover down and lift it away

from the compartment. Insert four AAA batteries (alternate positive ends (+)

toward the top of the transceiver, starting left-to-right.

2. Then lift cover at

bottom to open.

Remove cover.

3. Insert four AAA batteries

(positive (+) end toward

the top begining at left

side and alternating

positive terminals as

shown).

1. Using thumb,

press down on

battery cover at

arrow and slide

cover down.

CLIP SPRING

RELEASE TAB

BATTERY

COVER

CARRY

CLIP

COVER

ARROW

POSITIVE

TERMINALS

+ +

128-6675

7 of 24

The following guidelines will improve performance and provide longer

operating times for the FRS122-2:

1. Do not mix old and new batteries.

2. The use of alkaline-type batteries is recommended to provide the

longest operating time.

3. Do not mix alkaline, standard (carbon-zinc) or rechargeable

batteries.

4. If the unit is not to be used for an extended period of time, remove the

batteries. Old or leaking batteries can cause damage to the unit and

will void the warranty.

NOTE:

Only

Audiovox

approved rechargeable

batteries (P/N GMRS1222BAT)

can be recharged in the radio

transceiver.

MODE

LOHI

MIC/CHG/

SP JACK

OPTIONAL AC WALL

ADAPTER/CHARGING

TRANSFORMER

MODEL: GMRS1222AC

ADAPTER

POWER

PLUG

AUDIO OX

LISTED

81J1

E81356

FRS122-2

INPUT: 110VAC

OUTPUT: 7.5VDC

128-6675

8 of 24

FRS122-2 OPERATIONAL MODES

NOTE: To differentiate between operating modes, look for HI or LO

indication below the battery power level indicator when in FRS

mode.Refer to the appropriate section of this manual for de-

tailed operating instructions for each mode. Channels 1 through

14 are shared FRS only,

Controls:

Power On-Off/SCAN Button (13)

Press and hold the PWR on/off button for at least 2 seconds. You will hear

a confirming melody to indicate the unit is on. To turn the unit off, press and

hold the button for at least 2 seconds.

Adjusting the Volume (11, 10)

With the unit powered on, press the Up Channel/Volume button (

) to

increase volume and the Down Channel/Volume button ( ) to decrease

FRS

(MODE)

POWER

SELECT

CTCSS

SELECT

CHANNEL

SELECT

ROGER

BEEP

(1-14)

(oF, 01-38)

(on or oF)

128-6675

9 of 24

volume. The display will indicate the current volume level (VL) followed by

the number (0-7). As volume is increased upward, the unit will beep at

each step, and vice-versa. When the minimum and maximum volume

settings are reached, a unique tone will sound.

Monitor/Display Backlight Button (2)

This button is used to to check activity on the current frequency before

transmitting. Check activity by pressing the Monitor (M) Button longer

than 2 seconds; the

icon will apppear on the display and you will

hear static if frequency is clear.

Do not transmit if you hear conversation.

Hold down the Monitor Button again longer than 2 seconds and the

icon will disappear from the display.

The monitor function will temporarily bypass the squelch setting and play

all signals on a given channel. This feature is useful when communicating

with other parties at extreme range.

By pressing the monitor button momentarily, the LCD backlight is turned

on; the LCD backlight will turn off automatically in about 5 seconds, unless

the monitor button is pressed momentarily once again.

Push To Talk (PTT) Button (4)

Pressing and holding this button will allow you to speak to any transceiver

that is set to the same channel and privacy code setting as yours. Hold the

transceiver approximately 1 to 2 inches from your face as you speak into

the built in microphone (9). After you have finished speaking, release the

PTT Button to allow reception of incoming signals. It is not possible to

transmit and receive at the same time. Whenever the button is pressed,

the transmit signal icon (

) will appear in the upper left corner of the

display. Releasing the button allows the unit to revert to standby mode.

When receiving an incoming signal, the

icon will appear.

The PTT Button can also be used as a two-way call ringer. Pressing the

button twice quickly will call another party on the same channel. The transmit

icon (

) will be displayed for 3 seconds and then disappear.

128-6675

10 of 24

Up Channel/Volume Button (10)

In the standby mode, pressing this button will increment the listening

volume. When in function edit mode this button will be used to adjust the

unit’s settings.

Down Channel/Volume Button (11)

In the standby mode, pressing this button will decrement the listening

volume. When in function edit mode this button will be used to adjust the

unit’s settings.

MODE Button (12)

This button is used to select various feature settings in the FRS

modes.

External Speaker (SPK)/ Microphone (MIC)/CHG Jack (6)

This jack accepts both the optional Audiovox headset/microphone connector

and the supplied wall charging adapter. For additional optional equipment

and accessories for the FRS122-2, visit the Audiovox web site at

www.audiovox.com.

Scan Button (13)

With the unit in standby mode, press the Power On/Off Button momentarily

to enable or disable the scan function; SCAN will appear on the display.

128-6675

11 of 24

Operating Modes and Features

FRS Operation:

- Press and hold the Power On/Off button for 2 seconds to turn on

power.

- Press the MODE button so the Channel number flashes.

- Select the desired channel with the Up (10) and Down (11) Buttons.

When receiving a call, the

icon appears to indicate an incoming

call.

- Press and hold the PTT button (4) to transmit, then speak into the

microphone clearly and slowly. The Transmit icon (

) appears

on the display while the button is pressed.

- Release PTT Button (4) to receive.

- Communication can only be accomplished when the channel and

CTCSS tone frequency of at least two parties are the same.

- The CTCSS subcode (01-38) will be displayed on the LCD panel if the

CTCSS tone frequency function is enabled (not oF).

Channel Selection

In order to communicate with other FRS units, both the transmit-

ting and receiving party must be on the same frequency.

The FRS122-2 has 14 channels (frequencies) indicated by the large

digits on the LCD display panel. Channels 1 through 14 are the shared

FRS channels.

Communication with Audiovox FRS

and compatible units is possible on these 14 channels. Before trans-

mitting on the selected channel, press the Monitor (M) Button (2) to check

the activity on that channel. If there is activity on the selected channel,

change to another channel that is clear.

128-6675

12 of 24

To change the channel:

- From FRS standby mode, press the MODE button (12) once

the channel number flashes.

- Press the Up Button (10) briefly to move to the next higher main chan-

nel number.

- Press the Down Button (11) briefly to move to the next lower main

channel number.

- Press the PTT button momentarily to confirm selection.

CTCSS Mode (Sub-Channel) Selection

The Coded Tone Controlled Squelch System (CTCSS) has 38 Sub-Frequencies.

This feature allows you to utilize the coded squelch tones (01-38) within a

main channel and enables you to communicate with another party on the

same main channel using the same subcode. (This filters out unwanted

transmissions from the same main channel). Since there are 38 CTCSS

Sub-channels for each main channel, a different subcode may be se-

lected for each of the 14 channels.

To change the CTCSS Sub-channel:

- From FRS standby mode, press the MODE Button twice; a flash

ing oF or sub-channel number is displayed.

- Press the Up or Down button to select the desired sub-channel for

use (01-38 ).

- Press the PTT button to confirm selection.

The CTCSS mode can be turned off by selecting the oF icon as the setting.

NOTE: To communicate with other FRS units, they must be

switched to the same channel and CTCSS subcode. To commu-

nicate with other FRS units that do not have subcodes, switch

your unit to the same channel with the subcode set to oF.

The CTCSS subcodes do not prevent others from hearing your

transmission. This will only allow you to ignore all traffic on a

given channel not using the same subcode.

128-6675

13 of 24

Roger Beep Tone

The Roger Beep is a tone which is automatically transmitted whenever the

PTT button is released and the tone is enabled. This tone alerts the

receiving party that the transmission has been terminated intentionally.

128-6675

14 of 24

To enable and disable the Roger Beep tone:

- From FRS standby mode, press the MODE Button 3 times

until the flashing Roger Beep icon (

) appears

with On or oF.

- Press the Up or Down Button to select the tone on or off as desired.

- When enabled, the tone icon (

) appears steady on the display.

- Press the PTT button momentarily to confirm selection.

VOX Selection Mode

This option enables you to have hands-free conversation. When using the

internal microphone/speaker or external microphone/headset (purchased

separately), your voice or the signal is detected and the radio transmits

and receives automatically. Your voice or nearby sound is detected and

the radio transmits without the need to press the PTT button.

To set the radio for VOX operation:

- From FRS standby mode, press and hold the MODE button

for 3 seconds, or until the VOX icon appears on the display.

- To terminate VOX operation, press and hold the MODE button for at

least 3 seconds; the VOX indication will disappear.

Button Beep (Key Tone)

This feature allows the transceiver to sound a confirmation tone whenever

the following keys are pressed: Power On/Off/SCAN Button, Up/Down But-

tons and MODE Button. This feature is always on.

Call Ringer Selection Mode

The transceiver provides a transmit call ring melody at the receiving unit to

alert you to an incoming call.

To activate the call ringer melody:

- From FRS standby mode, press the PTT button twice in quick

succession; a call ring melody will sound at the receiving unit to alert

the user to an incoming transmission, provided that unit is equipped

with this capability and set to the same channel.

128-6675

15 of 24

Channel Scan Operation

This feature allows you to monitor all channels automatically for valid

signals. While scanning, you can transmit and receive. When a signal is

received, the scan is interrupted and will return to scan mode approxi-

mately 5 seconds after reception is terminated.

NOTE: While the SCAN mode is active, the MODE button is inopera-

tive. In addition, the scan mode will reduce the overall battery life

since the battery save function is overridden.

To enable the channel scan mode:

- From FRS standby mode, momentarily press the Power On/Off

Button; SCAN will appear on the LCD display.

- The radio will automatically display each channel (1-14) in ascending

order to find an active main channel.

- When the unit doesn’t find any signals and you want to transmit, press

the PTT Button to return to primary channel operation. The transceiver

will automatically resume scanning approximately 15 seconds after

the communication is completed.

- If there is no activity and you want to leave the scan mode, press the

Power On/Off button momentarily and the unit will return to normal op

eration; the SCAN icon will disappear from the LCD display.

128-6675

16 of 24

Battery Alert

When the battery icon (

) blinks steadily on the LCD panel, recharge

the unit or install fresh batteries.

NOTES FOR GOOD COMMUNICATION

1 . The FRS122-2 14 channels are shared on a ‘take turns’ basis.

This means other groups may be talking on any of the channels.

A common code of ethics/courtesy is to switch to another vacant

channel and not to attempt to talk over someone who is already using

the channel you first selected.

2. The FRS122-2 has been designed to maximize performance

and improve transmission range in the field. To avoid interference,

it is recommended that you do not use the units closer than 5 feet

apart.

3. For best transmission results, always keep your mouth about 2-3

inches from the microphone (9) and speak slowly in a normal voice.

4. To increase battery life, use the SCAN feature sparingly. This

feature will reduce operating time considerably.

Warning

•

Remove the batteries from the transceiver if it is not expected to be used

for long periods. This will eliminate the possibility of chemicals leaking

from the batteries and corroding the transceiver.

•

Avoid exposing the transceiver to water or extremes of temperature.

•

Do not use this device in or near a mining facility, which uses remotely

triggered explosives or in areas labeled “Blasting Area”. Premature or

accidental detonation may result.

128-6675

17 of 24

•

Do not attempt to modify or in any way increase the output of this

transceiver. Its output is designed to meet the legal limits set by the FCC.

•

Do not use this device or change its batteries in potentially explosive

atmospheres as sparks in such areas could result in an explosion.

•

Turn your transceiver off wherever posted notices restrict the use of radios

or cellular telephones. Facilities such as hospitals may use equipment

that is sensitive to RF energy.

•

Turn your transceiver off on board aircraft when requested to do so.

•

Do not place your radio in front of a vehicle’s air-bag. If the air-bag

deploys, it could propel the transceiver like a projectile causing bodily

injury.

128-6675

18 of 24

Troubleshooting

Weak or no Weak batteries Charge or replace batteries

signal received Channel and privacy Adjust the transceiver’s

code not set the same settings to match those

as target transceiver settings of the target

transceiver

Volume level too low Increase volume level

PTT Button inadvertently Release PTT Button

depressed

Excessive radio interference Change to a different

on a particular channel channel

Obstruction of radio signal Avoid operating in or near

large buildings or vehicles

Unit beeps, but Batteries extremely Charge or replace batteries

will not function discharged

when turned on

Reception of CTCSS privacy mode Turn on the CTCSS privacy

unwanted signals not on mode and set code number to

match the setting of the

target transceiver.

Interference from Turn the devices off or move

electronic devices such farther away from them.

as computers or TVs

Problem Possible cause Correction

No transmission Weak batteries Charge or replace batteries

while pressing Incorrect battery polarity Install the batteries

the PTT Button following the directions in

paragraph Installing the

Batteries.

128-6675

19 of 24

General

Frequency Range:

Channels 1 through 7 are

shared with FRS radios. Refer to frequency chart on next page.

Channels 8 through 14 are

FRS only. Refer to frequency chart on next page.

Channel Spacing 12.5kHz

Privacy Codes 38 for each main channel

Dimensions (W x H x D) 2.25” W x 3.68” H x 1.125” D

(Without Antenna) (56.0 mm x 93.7 mm x 28.5 mm)

Power Supply

Power Source Alkaline Batteries, AAA (4), 6 VDC

Ni-MH rechargeable, AAA (4),

4.8 VDC, 650 mAh

Operating Time 30 hours Low Power

(Transmit: Receive: Standby) 14 hours High Power

(5: 5: 90 ratio)

(Based on alkaline batteries)

Receiver

Useable Sensitivity >-119 dBm

Maximum Audio Output Power > 0.3 Watt maximum (8 Ohm )

Modulation Distortion < 5% (1 kHz 70%)

Transmitter

RF Output Power 1.8 Watts maximum (high power)

0.5 Watt maximum (low power)

Maximum Deviation +/- 2.5 kHz

Modulation Distortion < 5% (1 kHz 70%)

Technical Specifications:

128-6675

20 of 24

NOTE: Channels 1 through 7 are shared with FRS radios.

Channels 8 through 14 are FRS only.

This transceiver complies with FCC regulations for use in the United

States of America. Use in other countries may be prohibited or restricted

by local regulation. Please check with the local regulating agency be-

fore using this device outside the United States of America.

Main Channel Frequencies:

EPYT/LENNAHC)zHM(QERFEPYT/LENNAHC)zHM(QERF

SRF/SRMG15265.264SRF215266.764

SRF/SRMG25785.264SRF315786.764

SRF/SRMG35216.264SRF415217.764

SRF/SRMG45736.264SRMG510055.264

SRF/SRMG55266.264SRMG610575.264

SRF/SRMG65786.264SRMG710006.264

SRF/SRMG75217.264SRMG810526.264

SRF85265.764SRMG910056.264

SRF95785.764SRMG020576.264

SRF015216.764SRMG120007.264

SRF115736.764SRMG220527.264

Page is loading ...

Audiovox FRS122-2 User manual

Brand: Audiovox

Model: FRS122-2

Category: Two-way radios

Type: User manual

Download PDF

report

Audiovox FRS122-2 User manual

Audiovox FRS122-2 User manual

Related papers

Other documents