3M Fluorinert™ Electronic Liquid FC-3283 User guide

Brand: 3M

Model: Fluorinert™ Electronic Liquid FC-3283

Type: User guide

This manual is also suitable for

Carrier and lubricant deposition solvent applications

using 3M

™

Fluorinert

™

Electronic Liquids

When creating new coatings, lubricants and other formulations, it is crucial to have the appropriate solvency, surface

tension, dielectric strength, and boiling point, as well as non-ammability. These factors can signicantly impact your

product quality, as well as how the product performs for your customer. That’s why we developed 3M

™

Fluorinert

™

Electronic Liquids, oering a wide variety of solutions for you to choose from.

Property Unit

™

Fluorinert

™

Electronic Liquids

FC-3284 FC-72 FC-770 FC-3283 FC-40 FC-43 FC-70

Boiling Point °C (F) 50 (122) 56 (132) 95 (203) 128 (262) 165 (329) 174 (345) 215 (419)

Dielectric Breakdown

Strength (over 0.1 in gap)

kV >40 kV >40 kV >40 kV >40 kV >40 kV >40 kV >40 kV

Flash Point

°C (°F) None None None None None None None

Vapor Pressure kPa 35 31 6.6 1.4 0.29 0.19 0.02

Heat of Vaporization kJ/kg 105 88 86 78 68 70 69

Liquid Density g/cm

1.71 1.68 1.79 1.82 1.85 1.86 1.94

Kinematic Viscosity cSt 0.42 0.38 0.79 0.75 2.2 2.5 12

Specic Heat J kg

-1

1100 1100 1038 1100 1100 1100 1100

Surface Tension mN/m 13 10 15 15 16 16 18

Solubility of Water in Fluid ppm by weight 14 10 14 7 <7 7 8

Solubility of Fluid in Water ppm by weight <5 <5 <5 <5 <5 <5 <5

Solubility

Fluorocarbon Very High Very High Very High Very High Very High Very High Very High

Hydrocarbon Low Low Low Low Low Low Low

Plastic Elastomer

Compatibility

–

™

Fluorinert

™

Electronic Liquids are compatible with most plastics and elastomers.

Contact 3M for more information.

Results are typical. Not for specication purposes. All values @ 25°C unless otherwise specied.

Per closed cup flash point, tested in accordance with ASTM D3278 test method.

3M EMSD Medical Device Policy

These 3M products are intended for use as process solvents in applications, such as formulating coatings and lubricants. They are not intended, nor approved,

for incorporation into medical devices or for use in pharmaceuticals. 3M will not support applications such as lung perfusion or blood substitutes that involve

temporary or permanent implantation of these 3M products. Read a complete statement of 3M Electronics Materials Solutions Division's Global Policy

regarding the sale and use of products for medical and pharmaceutical applications.

IMPORTANT NOTICE: The technical information, recommendations and other statements contained in this document are based upon tests or experience

that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Contact your local 3M representative or visit 3M.com/

electronics for more information. Warranty and Limitation of Liability: if there is a defect in this product, your exclusive remedy shall be product replacement

or refund of the purchase price. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, INCLUDING ANY IMPLIED WARRANTY OR CONDITION OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 3M will not be liable for any direct, indirect, special, incidental or consequential damage

related to the use of this product.

Electronics Materials Solutions Division

3M Center, Building 224-3N-11

St. Paul, MN

55144-1000

Phone 1-800-810-8513

Web www.3M.com/electronics

3M and Fluorinert are trademarks of 3M Company.

60-5002-0959-2

9/2016