American Pro Decor 5APD10754 Installation guide

Type
Installation guide

This manual is also suitable for

American Pro Decor 5APD10754 is a hardware kit for sliding single wood doors. It includes all the necessary components to install a sliding door, including door roller hardware, a 78" rail with soft close mechanism, soft close trigger hardware, wall brackets, door stops, an Allen key, anti-jump disks, a routed floor guide, and floor anchors.

The kit is designed for easy installation and can be completed in a few hours. The soft close mechanism ensures that the door closes smoothly and quietly, while the anti-jump disks prevent the door from jumping off the track. The routed floor guide helps to keep the door in place and prevents it from swaying.

American Pro Decor 5APD10754 is a hardware kit for sliding single wood doors. It includes all the necessary components to install a sliding door, including door roller hardware, a 78" rail with soft close mechanism, soft close trigger hardware, wall brackets, door stops, an Allen key, anti-jump disks, a routed floor guide, and floor anchors.

The kit is designed for easy installation and can be completed in a few hours. The soft close mechanism ensures that the door closes smoothly and quietly, while the anti-jump disks prevent the door from jumping off the track. The routed floor guide helps to keep the door in place and prevents it from swaying.

TOOLS REQUIRED
INCLUDED IN KIT
• Plumb Line
• Pencil
• Phillips Head Screwdriver
• 8mm Drill Bit
• 10mm Routing Drill Bit
• 5.5mm Drill Bit
• Wrench
• Level
• Tape Measure
• Power Drill
A
B
C
D E
F
G
H I J
K L M
A
Door Roller Hardware x2
B
78" Rail + Soft Close Mechanism (x2)* x1
C
Soft Close Trigger Hardware x2
D
Wall Bracket x5
E
Door Stop x2
F
2.5mm Allen Key x1
G
Anti-Jump Disk x2
H
Routed Floor Guide x1
I
Floor Anchor x2
J
ST4.2x25 Screw x2
K
M8x30 Wall Anchor x5
L
M8x60 Bolt + Washer x5
M
M8x90 Bolt x5
* Soft Closing Mechanisms are pre-attached to rail.
* *
MODEL No.
5APD10755
INSTALLATION MANUAL
HARDWARE KIT
FOR SLIDING SINGLE WOOD DOORS
American Pro Decor assumes no liability for improper installation.
Wall Blocking
To obtain maximum weight capacity, all fasteners
must be mounted into solid wood studs or wall
blocking or mounted to a header board.
Minimum door overlap on guide is 2"
Find the centerline of the track. Using a level, mark a
horizontal line twice the door width long. Mark the brack-
et screw locations into the wall blocking. Attach the wall
portion of the brackets as shown.
Attach the rail to the wall brackets using a wrench to fasten
the bolts as shown.
NOTES
Consult a structural engineer if you have questions
about what type of wall blocking is required.
American Pro Decor assumes no liability for improper installation.
Drill out holes in the door using a 10mm routing drill bit as
pictured. The bottom of the doors should be routed at this
time in order to accept the oor guide.
Attach the door to the rails making sure that the
anti-jump disks are engaged to avoid a serious accident.
Plumb the door and mark the positions of the oor guides.
Mount the oor guides to the oor.
Attach the anti-jump disks to the tops of the door.
American Pro Decor assumes no liability for improper installation.
Adjust the door stops accordingly using the provided 2.5mm Allen key.
Set the catches on the soft-closing mechanism to the open position. To determine the positioning of the soft-close
triggers, it is recommended that the doors be moved to the fully open position. Determine where the soft-close trigger
would engage the soft-close mechanism and mark your drill holes on the top of the door. Move the door to the fully
closed position and repeat to determine the placement of the second soft-close trigger.
It may be necessary to adjust the height of the door roller hardware in order to accommodate the soft-close trigger.
Make any adjustments with the provided adjustable installation wrench then mount the soft-close triggers to the door.
American Pro Decor assumes no liability for improper installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Pro Decor 5APD10754 Installation guide

Type
Installation guide
This manual is also suitable for

American Pro Decor 5APD10754 is a hardware kit for sliding single wood doors. It includes all the necessary components to install a sliding door, including door roller hardware, a 78" rail with soft close mechanism, soft close trigger hardware, wall brackets, door stops, an Allen key, anti-jump disks, a routed floor guide, and floor anchors.

The kit is designed for easy installation and can be completed in a few hours. The soft close mechanism ensures that the door closes smoothly and quietly, while the anti-jump disks prevent the door from jumping off the track. The routed floor guide helps to keep the door in place and prevents it from swaying.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI