© 2020
Order #XXXXX
Locked layer contains
placeholder marks.
Top View
Perspective View
20’
10’
VK-2934 General Layout
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2020
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2020
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation
© 2020
Case 1 of 5
Order #XXXXX
Lights
Setup Hardware
Top View of Each Level
Level 1 (Bottom Level) Level 2
Wings (Qty. 4) 17 16 16A 17A
Monitor
Mount
Monitor
Mount
Case Packing
© 2020
Case 2 of 5
Order #XXXXX
Lights
Top View of Each Level
Level 1 (Bottom Level) Level 2
4A,4 9,7
Level 3
5A,5
10,10A 11,11A
14
13
12
15
14
15
Graphics
Case Packing
© 2020
Case 3 of 5
Order #XXXXX
Top View of Each Level
Level 1 (Bottom Level) Level 2
18,18A 20,20A
19,19A 1 (Qty. 2)
1 (Qty. 4)
17 16 16A 17A
Level 3
Monitor
Mount
Case Packing
© 2020
Case 4 of 5
Order #XXXXX
Top View of Each Level
Level 1 (Bottom Level) Level 2
Shelf
Counter
Level 3 Level 4
Shelf Supports
Infills (Qty. 4)
Pedestal Back
Assembly
Pedestal Front
w/ Door Assembly
Case Packing
© 2020
Case 5 of 5
Order #XXXXX
Top View of Each Level
Level 1 (Bottom Level) Level 2
Shelf
Counter
Level 3 Level 4
Shelf Supports
Infills (Qty. 4)
Pedestal Back
Assembly
Pedestal Front
w/ Door Assembly
Case Packing
© 2020
Step 1 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
1
2,2A
3,3A
4,4A
5,5A
Qty.
2
1
1
1
1
Description
Base Plate
48”h Vertical Extrusion
48”h Vertical Extrusion
41.7083” Curved Horizontal Extrusion
41.7083” Curved Horizontal Extrusion
Steps:
1) Attach base plates [1] to lower verticals [2] and [3], using bolts.
2) Connect verticals [2] to [2A] and [3] to [3A]. See
Extrusion Connector detail.
3) Connect horizontals [4] to [4A] and [5] to [5A]. See
Horizontal Connector detail.
4) Attach horizontal assemblies [4/4A] and [5/5A] between
vertical assemblies [2/2A] and [3/3A].
5) Attach clamps to verticals [2/2A], where indicated.
See Clamp Attachment detail.
2
2A
Clamp
3
3A
1
1
44A
5A
5
Velcro
PR37
Extrusion
Profile
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro on extrusions
must face to BACK of
assembled Backwall.
When desired location
is found, tighten
set screw to secure.
Slide connector, located on
back of clamp, into groove
of extrusion.
Clamp
Clamp Attachment
Keep clamps attached to verticals, when packing.
Knob
Set Screw
A10 Clamp
Horizontal Connector
*
PR53
Connector
Z45 Z45
Insert connector into extrusions.
Secure with set screws.
Set Screw
To prevent product loss, keep all
screws attached to connector
after disassembling.
*
*
**Set
Screw
Extrusion Connector
Set
Screw
*
Slide extrusion over connector
then secure with set screws.
To prevent product loss, keep
all screws attached to
connector after disassembling.
Connector
Keep connectors attached to [2] [3] and [5], when packing.
Backwall Assembly
© 2020
Step 2 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Front View
Front View
SEG Graphic
Blocker Fabric
Velcro
Item
6
7
8
9
10,10A
11,11A
12
13
Qty.
1
1
1
1
1
1
1
1
Description
48”h Curved Vertical Extrusion
48”h Curved Vertical Extrusion
48”h Curved Vertical Extrusion
48”h Curved Vertical Extrusion
38.5”w Horizontal Extrusion
38.5”w Horizontal Extrusion
46.2573"w Horizontal Extrusion
48"w Horizontal Extrusion
Steps:
1) Assembled extrusions together, as shown.
See connection details.
2) Connect blocker fabric to assembled frame.
3) Install SEG graphic to assembled frame.
See SEG Graphic Installation sheet for
instruction.
7
6
9
8
10 10A
11 11A
12
13
Velcro attached
to back of extrusion,
for lights.
TSP46
*
**
**
*
**
TSP46 Straight Connection
*
PR53
Connector
TSP46
TSP46
Insert connector into extrusions.
Secure with set screws.
Set Screw
To prevent product loss, keep all
screws attached to connector
after disassembling.
*
Lock
Set Screw
Slide end of extrusion over
Lock. Tighten set screw to
secure extrusions together.
TSP46 Corner Connection
Frame Assembly
© 2020
Step 3 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
14
15
Qty.
2
2
Description
4.5” Horizontal Extrusion
4.5” Horizontal Extrusion
15
14
Steps:
1) Attach assembled frame to assembled backwall,
using horizontals [14] and [15].
2) Attach lights to Velcro on back of assembled frame.
Velcro on back
Attach lights to Velcro
on back of extrusion.
15
14
Frame to Backwall Assembly
© 2020
Step 4 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Connect Light to the upper horizontal of SEG Frame.
See Light Connection detail.
2) Attach wings to clamps on verticals [2/2A].
See Clamp Attachment detail.
3) Attach monitor mount to horizontals [12] and [13].
See Monitor Mount Attachment detail.
Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
*
*
Monitor
Mount
Clamp
2
2A
Wing
Wing
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
A10 is in desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
Clamp Attachment
A10 Clamp
SEG Graphic
Attach monitor mount to horizontal extrusions, using bolts
and wing nuts.
Note: Monitor mount attaches over SEG graphic.
*Monitor Mount Attachment
Wing
Nut
Bolt
Monitor
Mount
Backwall Attachments
© 2020
Step 5 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Attach base plates [1] to lower verticals [16] & [17], using bolts.
2) Connect verticals [16A to 16] and [17 to 17A].
3) Connect curved horizontals [18 to 18A] and [19 to 19A].
4) Attach curved horizontal assemblies [18/18A] & [19/19A]
between verticals [3/3A] & [16/16A].
5) Attach horizontals [20] & [20A] between verticals [16/16A] & [17/17A]
6) Connect graphic to Velcro on back of assembled frame.
Item
1
16/16A
17/17A
18/18A
19/19A
20/20A
Qty.
2
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
48”h Round Vertical Extrusion
48”h Round Vertical Extrusion
38” Curved Horizontal Extrusion
38” Curved Horizontal Extrusion
38” Curved Horizontal Extrusion
16 17
16A 17A
18A
18
19A
19
3A
3
20
1
1
20A
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge
Velcro on extrusions
must face to BACK of
assembled Backwall.
Velcro
PR37
Extrusion
Profile
When assembled
Backwall Assembly (Cont’d)
© 2020
Step 6 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Connect lights to upper horizontals, where indicated.
See Light Connection detail.
2) Connect wings to vertical [17/17A], using clamps.
See Clamp Attachment detail.
3) Attach monitor mounts to verticals, where indicated.
See Monitor Mount detail.
**
***
Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
Monitor Mount
Slide connectors into groove
of vertical extrusion. Tighten
set screws to secure in place.
Attach monitor mount back
plate to connectors, using bolts.
*
Bolts
Monitor
Mount
Connectors
with Set
Screws
When desired location
is found, tighten
set screw to secure.
Slide connector, located on
back of clamp, into groove
of extrusion.
Clamp
Clamp Attachment
Keep clamps attached to verticals, when packing.
Knob
Set Screw
A10 Clamp
When assembled
Monitor
Mount Monitor
Mount
Wing
Wing
Backwall Attachments (Cont’d)
© 2020
Step 7 of 7
Order #XXXXX
Locked layer contains
placeholder marks.
*
Item
21
22
23
24
25/25A
26/26A
23
Door
Infill
Infill
Infill
21
24
25
25A
25A
Shelf
Counter
25
22
Qty.
2
2
2
2
8
8
Description
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
13”w Horizontal Extrusion
10”w Horizontal Extrusion
Steps:
1) Attach lower horizontals [25] and [26] between verticals
[21] [22] [23] and [24].
2) Connect door to vertical [24]. See Door Connection detail.
3) Slide infills between verticals [21] [23], [21] [22], and [22] 24],
making sure Velcro is facing inward.
4) Attach upper horizontals [25A] and [26A] between verticals
[21] [22] [23] and [24], to secure infills.
5) Connect shelf supports to Velcro.
6) Place shelf on top of shelf supports.
7) Lock counter to horizontals [26A]. See Counter Lock detail.
26
26
26A
26A
Door
Hinge
Hinge
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
Counters Being Assembled are
Highlighted in BLACK
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Lock
12
*
Pin
Hole
*
*
*
Backwall Counter Assembly (Qty. 2)
/
