Continental Industries (CI) 0000-34-7144-29-adapter-coupling Installation guide

Brand
Continental Industries (CI)
Model
0000-34-7144-29-adapter-coupling
Type
Installation guide

Continental Industries (CI) 0000-34-7144-29-adapter-coupling is designed to connect PE pipe or copper pipe to metallic tubing. It has a pressure rating that meets or exceeds the pressure rating of PE pipe per 49 CFR Part 192 and ASTM D 2513. The adapter coupling is not a full restraint design, so proper pipe anchorage must be provided where pipe movement out of the outlet might occur. To install the adapter coupling, cut the pipe ends square, deburr the outside and inside, and clean thoroughly. Mark the stab length on the pipe or tubing and insert it into the outlet until it bottoms.

Continental Industries (CI) 0000-34-7144-29-adapter-coupling is designed to connect PE pipe or copper pipe to metallic tubing. It has a pressure rating that meets or exceeds the pressure rating of PE pipe per 49 CFR Part 192 and ASTM D 2513. The adapter coupling is not a full restraint design, so proper pipe anchorage must be provided where pipe movement out of the outlet might occur. To install the adapter coupling, cut the pipe ends square, deburr the outside and inside, and clean thoroughly. Mark the stab length on the pipe or tubing and insert it into the outlet until it bottoms.

The Ultimate Connection
CONTINENTAL INDUSTRIES
The Ultimate Connection
34-7144-29
ECN 2625 REV "D" 08/25/14
ADAPTER COUPLING INSTALLATION INSTRUCTIONS PE
COMPRESSION OUTLET ASSEMBLY INSTRUCTIONS
1. CUT PIPE ENDS SQUARE, DEBURR OUTSIDE AND INSIDE, CLEAN THOROUGHLY TO ASSURE THERE IS NO DIRT, GREASE, OIL, ETC.
ON ASSEMBLY AREA OF PIPE.
2. MARK STAB LENGTH ON PIPE (SEE EXAMPLES FOR CORRECT PIPE OR TUBING SIZE AND CORRESPONDING STAB LENGTH).
3. LOOSEN COMPRESSION NUT UNTIL SEAL RING IS NO LONGER COMPRESSED. THEN INSERT PIPE UNTIL IT BOTTOMS IN OUTLET.
(SEE DETAIL "A")
4. TIGHTEN COMPRESSION NUT UNTIL IT SHOULDERS AGAINST THE OUTLET. DO NOT OVER TIGHTEN (SEE DETAIL "B") LINE
MARKED FOR STAB LENGTH SHOULD BE NO MORE THAN 3/4" FROM FACE OF NUT.
METALLIC TUBING COMPRESSION OUTLET ASSEMBLY INSTRUCTIONS
1. MAKE SURE THAT TUBING SURFACE IS CLEAN AND FREE OF COATINGS.
2. MARK STAB LENGTH ON TUBING SEE ABOVE.
3. REMOVE THE COMPRESSION NUT, SEAL RING AND LOCK RING FROM THE FITTING. THE LOCK RING IS ON THE INSIDE OF THE
SEAL RING.
4. SLIDE THE COMPRESSION NUT OVER THE TUBING WITH THE OPEN END FACING THE CUT END OF THE TUBING.
5. SLIDE THE SEAL RING AND LOCK RING OVER THE END OF THE TUBING. THE LOCK RING SHALL NOT BE DISPLACED FROM
THE SEAL RING.
6. INSERT THE TUBING TO THE STOP IN THE FITTING.
7. PUSH THE SEAL RING, LOCK RING AND COMPRESSION NUT UP AGAINST THE FITTING.
8. TIGHTEN THE COMPRESSION NUT UNTIL IT BOTTOMS ON SHOULDER.
NOTE: The metallic compression outlet is not a full restraint joint. WHERE PIPE MOVEMENT OUT OF OUTLET MIGHT OCCUR,
PROPER PIPE ANCHORAGE MUST BE PROVIDED.
1 1/ 8" OD,
2 3/ 8" STAB LENGTH
IMPORTANT
For use on: PE pipe meeting the requirements of ASTM D 2513
Copper Pipe meeting the outer diameter specication of ASTM D 2513
Pressure Rating: Designed to meet or exceed pressure rating of PE
pipe per 49 CFR Part 192 and ASTM D 2513
Operating Temperature: 20° to 100° F
WARNING: The joint to metallic tubing is not a full restraint design.
Size Metallic Pipe Pullout
Resistance
1 1/8" OD Copper 500 lbs
  • Page 1 1

Continental Industries (CI) 0000-34-7144-29-adapter-coupling Installation guide

Brand
Continental Industries (CI)
Model
0000-34-7144-29-adapter-coupling
Type
Installation guide

Continental Industries (CI) 0000-34-7144-29-adapter-coupling is designed to connect PE pipe or copper pipe to metallic tubing. It has a pressure rating that meets or exceeds the pressure rating of PE pipe per 49 CFR Part 192 and ASTM D 2513. The adapter coupling is not a full restraint design, so proper pipe anchorage must be provided where pipe movement out of the outlet might occur. To install the adapter coupling, cut the pipe ends square, deburr the outside and inside, and clean thoroughly. Mark the stab length on the pipe or tubing and insert it into the outlet until it bottoms.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents