PSE Archery 2012 Bow User guide

Type
User guide
General OperatinG instructiOns
• Alwaysinspectyourbowthoroughlybeforeeachshootingsessiontoinsurethatitis
ingoodworkingorder.Checkforworn,looseormissingcomponentsandhavethem
replacedatanauthorizedPSEdealerasrequired,i.e.bushings,spacers,etc.
• Inspectyourarrowstoinsurethattheyarestraight,undamagedandthateachnockisin
goodcondition.Acrackednockcanbreakwhenfiredfromthebowandcausethebow
to“dryfire”resultinginpossibleinjurytothearcheranddamagetothebow.Dry-firing
isdrawingandreleasingthebowstringwithoutanarrowonthestring.
• Whenpurchasingarrowsforyourbow,consulttheselectionchartfromthearrow
manufacturerandselectthecorrectarrowforyourapplication.Alwaysuseanarrowthat
isatleast5grainsperpoundofpeakbowweight.Failuretodosocouldcausepersonal
injuryanddamagetoyourbow.
BOw Maintenance
YourPSEbowwillgiveyoumanyyearsofuseifmaintainedandcaredforproperly.
 IMPORTANT: Before servicing any PSE bow in a bow press, back out each limb
bolt 4 complete turns from bottomed position.
• Keepsyntheticcablesandstringswaxed.Applybowstringwaxtoyoursyntheticcables
andstringbeforeeachshootingsession.
• Stringsandcablesmustbereplacedperiodically.Aworncableorstringcansuddenly
breakcausingseriousinjurytothearcheranddamagetothebow.Itisrecommended
thatthestringandcablesbereplacedatleastevery5,000shotsor12months.
• Alwaysstoreyourbowinacooldryplace.Hightemperatures,suchasthosethatcan
occurintheinteriorofavehicle,cancauseseriousdamagetoyourbow.
• Afteruseinhighhumidityordampconditions,wipemetalcomponentsofbow
withalightoil.
safety
Aswithanyweapon,safeoperationofyourPSEbowmustalwaysbethehighestpriority.
ALWAYS WEAR SAFETY GLASSES WHEN HANDLING A BOW.
Donotattempttouseyourbowwithoutproperinstruction.Doingsocanresultin
seriousinjury.
a.Neverdry-fireanybow.Dry-firingisdrawingandreleasingthebowstringwithout
anarrowonthestring.Dry-firingwilllikelycausedamagetothebowandseriousinjury
tothearcher.Intheeventofadry-fire,haveanauthorizedPSEdealerinspectthebow
fordamage.DONOTdry-firethebowmultipletimes!
b.Alwaysbesureofyourintendedtargetaswellaswhatliesbehindthetargetarea.Anarrow
cantravelaconsiderabledistance,soitisimportanttohaveasafeandsoundbackstop.
c.Ifyoudrawabowandneedtoletitdown,dosoinaslowandcarefulmanner.Keep
yoursupportarmstraightandprepareforarapidandviolentlet-down.Avoidhitting
yourhandonprotrudingaccessoriessuchasthecableguardorquiver.Keepyour
headandfacebackandoutofdangerduringlet-down.Neverdrawabowwithapeak
weightaboveyourcomfortlevel.Alwaysuseabowslingwhendrawingabow.
d.Nevermodifyanypartoftheboworitscomponentsbydrillingextraholesorremoving
material.Thisvoidsthewarrantyandpresentssafetyproblems.
e.Itisnotrecommendedtotimethebowusingadrawboardunlessthedrawboardis
operatedbyawinchorothermechanicalpullingdevice.
ThankyoufromtheentirePSEfamilyforpurchasingaPSEbow!YourPSEbow
wasmanufacturedfromthefinestmaterialsavailableandhandcraftedwith
prideintheUSA.Withpropercareyouwillenjoytheuseofthisproductfor
yearstocome.
Pleasereadthisentirebookletbeforeshootingoradjustingyourbow.Remember,
manyadjustmentstoacompoundbowrequiretheuseofabowpress.Whenever
shootingabow,becertainofyourtargetaswellaswhatelseliesdownrange.
NOTE: IMPORTANT WARRANTY REGISTRATION INFORMATION IS ON PAGE 22
2
LIMB
TOP
LIMB
BOLT
SIGHT
ARROW
REST
GRIP
ARROW
STABILIZER
TOP CAM
BUSS
CABLE
BOW QUIVER
CABLE
GUARD
CABLE
SLIDE
BOW
SLING
BACKSTOP (SHOWN)
OR STINGSTOP
RISER
BOTTOM CAM
LIMB
POCKET
STRING
3
cOMpOunD BOw terMinOlOGy
AXLE
LIMB
BANDS
VANE
NOCK
LIMB
BANDS
BROADHEAD
BOTTOM
LIMB
BOLT
CABLE GUARD
DAMPER
CONTROL
CABLE
COUPLER
LIMB
SUPPORT
4
Compound Bow
USER’S GUIDE
settinG-up yOur BOw
NOCKING POINT PLACEMENT:
Fingershooters:Installthenockingpointsothatthe
arrowpassesthecenterofthearrowrestmountinghole
andrunsslightlypoint-downrelativetothetuningmark
onthewindowofthebow.
ReleaseAidshooters:Installthenockingpointsothatthe
arrowpassesthecenterofthearrowrestmountinghole
andrunsparalleltothealignmentmarkonthewindow
ofthebow.
NOTE:Alignmentmarksareforreference
only.Adjustmentswilllikelybenecessary
tonockingpointandin/outposition
duringtuning
.
ARROWREST ADJUSTMENT:
Whenshootingwithareleaseaid,thein/outposition
ofthearrowrestshouldbeadjustedsothatthe
arrowrunsparallelwiththetuningmarkonthe
shelfwhenviewedfromabove.Whenshooting
withfingersthearrowshouldpointslightly
outsidethetuningmarkontheshelf.
SIGHT ADJUSTMENT:
Whenadjustingthesightpinlocations,always
rememberto“followthegroup”.Thatis,ifthe
shotgroupistotheleftofthetarget,movethe
sightpinstotheleft.Iftheshotgroupislow,
movethesightpinsdown.
CABLE GUARD ADJUSTMENT
AND INSTALLATION:
InstallthecableguardasshowninFigureA.
Adjustthecableguardsothecablesjustclear
thearrowvanes.Onbowsusinganoffset
cableguardrod,adjustmentsmustbedone
withtherodintheupposition(approximately
2o’clock)asshowninFigureB(10o’clock
forlefthandedbows).Over-rotatingan
adjustablecableguardcreatesexcessive
arrowclearanceandmaycausethecable
totrackincorrectlyonthewheelsandcause
personalinjuryand/ordamagetothebow.
FigureA FigureB
Tuning
Mark
Arrowrestmountinghole
Alignment
Mark
••
Tuning
Mark
5
1. Removethesetscrewsfromthebaseusinga1/16”hexwrench.
2. InstalltheBackstopintothethreadedholebelowthe
 griponthestring-facingsideofthebow.
3. ExtendtheBackstopuntilitmakescontactwiththestring.Markthestring¼”above
 and¼”belowwhereitmakescontactwiththestring.RemovetheBackstopand
 addservingtothatareaofthestring.ReinstalltheBackstop.
4. Toavoidanypossibilityofthecablesstrikingthesetscrews,thesetscrewsmustbe
 facingawayfromthecables.Iftheyarenot,removetheBackstopbase,addthe
 washerprovidedandreinstalltheBackstopbaseasshown.
5. Securelytightenthebasetothebowhandle.
6. Extendrodfrombaseuntilrubberstoppercontactsthestring.Rotateroduntilthe
 indentationintherodclosesttothealignmenthole(seepicture)canbeidentified.
 Rodshouldberotated180°andtherod/stopperlightlypushedintothestringuntil
 thenextavailableindentationisvisible(Detentholesareoffset–seepicturebelow).
 Installthesetscrewstosecurerodinthisposition.Tightensetscrews.
BackstOp™ instructiOns
Servestring
inthisarea.
Setscrews
Alignment
hole
Addwasher
ifsetscrews
arenear
cables.
Note:ManyPSEbowmodelscomefromthefactorywiththeBackstopinstalled.
Theseinstructionsrefertoreinstallationoradjustmentifneededaftermakingadjustments
toyourPSEbow.
6
Compound Bow
USER’S GUIDE
Note:SomePSEbowmodels(Effective2012)comefromthefactorywiththe
PSEStingStop™Backstopinstalled.Theseinstructionsrefertoreinstallation
oradjustmentifneededaftermakingadjustmentstoyourPSEbow.
1. ThreadtheStingStop™nutallthewayuptowardthebumperoftheStingStop™rod.
2. ThreadtheStingStop™rodintothethreadedholebelowthegripontheriser.
 Thebowstringwillneedtobedisplacedslightlytoonesidetothreadthe
 rodintothebow.
3. UnscrewtheStingStop™untiltherubberbumperapproachesthebowstring.
 Markthestring¼”abovetherubberbumperinitshighestpositionand¼”below
 thebumperinitslowestposition.RemovetheStingStopandaddservingtothe
 markedareaofthestring.ReinstalltheStingStop.
4. AdjusttheStingStop™tothedesiredpositionandtightentheStingStop™nut
 againsttheriser.TheStingStop™designallowsforthebumpertobepositioned
 sothestringstrikesthecenterofthebumper.Itisdesiredtohavesomeclearance
 (approximately1/16”)betweenthebumperandthebowstringatbrace.
 ItispreferredtohavetheStingStop™rodintheuppositionifpossible,butmay
 notbepossibleinordertoachievethenecessaryclearanceandcontactpoint.
stinG stOp™ instructiOns
Servestring
inthisarea.
7
installatiOn Of accessOries
Arrowrest/Overdraw:Thearrowrestoroverdrawshouldbeinstalledaccordingtotheinstructions
receivedwiththeproduct.Itisusuallymountedtothe
riserinthethreadedholeonthesideoppositetheshelf
(Hole“A”)usingthehardwareprovidedwiththearrowrest
oroverdraw.
Sight:Thesightshouldbeinstalledaccordingtothe
instructionsreceivedwiththeproduct.Itisusually
mountedtotheriserinthethreadedholes(Holes“B”)on
thesideoppositetheshelfusingthehardwareprovided
withthesight.Somebowsareequippedwithmultiple
sightmountingholeswhichallowthesighttobemoved
upordown.
Stabilizer:Thestabilizershouldbemountedaccordingto
themanufacturer’srecommendation.Itisusuallymounted
inthethreadedholeonthefrontoftheriser(Hole“C”).
BowSling:Thebowslingattachestotheriserofthebow
generallywiththestabilizer.Ifastabilizerisnotused,
attachtheslingtotheriserwiththecorrectsizedbolt
usingtheholeprovidedforthestabilizer(Hole“C”).
Other aDjustMents
DrawWeight:Yourbowisfactory-settowithin2lbs.
ofthepeakdrawweightindicatedonthebowhangtag
andthelast2digitsoftheserialnumber.Changesin
drawweightcanbemadebyturningthelimbboltinor
out.Beforemakinganychangesinweight,turnthelimb
boltclockwisetothebottomposition.Neveruseextreme
torquewhenturningtheboltordamagetothelimbmay
occur.Thelimbboltthenmaybeturnedcounterclockwise
toobtainthedesiredweight,butNEVERmorethanthe
numberofturnsindicatedonthehangtag.Adjusteach
limbexactlythesame.
CAUTION:Onsomebowmodels,thelimbbolt
lockingscrew,limbsupportscrewsorpockettang
lockingscrewMUSTbeloosenedBEFOREadjusting.
Wheels/Cams: ManyPSEwheelsandcamshave
adjustablefeatures.Eachonecomesfromthefactory
setupandreadytousebuttheremaybeoccasionsthat
youneedtoadjustthecharacteristicsofyourbow.In
somecasesyouwillneedaPSETuneCharttodeterminewhattoadjust,andyoumayneedto
seeaPSEDealerforinformation.Ifyouarenotsureoftheadjustmentyouaremaking,stop
andseeyourPSEDealerforassistance.Inmanycases,anappropriatebowpresswillbe
neededtomakeadjustmentstocamsandwheels.Ifyoudonothaveanappropriatepress,
seeyourPSEDealer.
Your Authorized PSE Dealer is supplied with
technical information on PSE bows and cams.
Please see your Dealer for assistance
when making these adjustments.
Hole
A
Holes
B
Hole
C
8
Compound Bow
USER’S GUIDE
ViBracheck hush kit accessOries
LimbBandonSolidLimbCableGuardDamper
(Shownatfulldraw)
IfyourbowisequippedwithaCableGuardDamperitshouldbeevenwith
thecableslidewhenthebowisatrest.MorethanoneCableGuardDamper
canbeused.
Ifyoursolidlimbbowisequippedwithlimbbands,theproperplacementofthe
bandsisapproximately1/8”beyondthelimbfork.
Ifyoursplitlimbbowisequippedwithlimbbands,theproperplacementofthe
bandsisatleast1/4”awayfromthecam(alignthebandwiththeendof
thelimbgraphic).
LimbBandonSplitLimb
pse asyMMetric iDler
PSEsinglecambowsareequippedwitha
specialasymmetricidlerwheel,whichis
assembledonthetoplimb.Itisessential
thattheidlerbeorientedproperly.
Thewideedgeoftheidleralwaysgoes
tothecableguardsideofthebow.
Theillustrationshowstheproper
orientationoftheidlerforaright-
handedbowwhenviewedwhile
holdingthebowasitisshot.
Wideedge
9
caM aDjustMents
Cam ORIEntatIOn:
Oncamswithorientationmarks,areferencemarkisfoundtoindicateanapproximate
orientation.Thislineisforreferenceonlyandismeanttogiveapproximateorientation
onlyandmayvarybetweenbowmodels.Theorientationofthecamsmaybechanged
slightlybytwistingoruntwistingthestringorcables.Ifattachingthestringtothe“+”or
the“-“post,theorientationmarkswillnotbealignedwiththecable.
DRaw LEnGth: 
StRInG POSt aDJUStmEntS
SomePSEcamshavestringpostadjustmentsfordrawlength.Forminorchangesindraw
length,thebowmustbeplacedinasuitablebowpressandtensionrelievedfromthe
stringandcable.Thestringsideofthecammayhaveadditionalposts.Movingthestring
fromthepostwiththedottothepostwiththe“+”willincreasedrawbyapproximately¼”.
Movingthestringfromthepostwiththedottothepostwiththe“-“willdecreasedrawby
approximately¼”.
aLL InnER-CamS:
Theinner-camsystemallowsdrawlengthadjustmentsoveraprescribedrangeusually
withoutputtingthebowinabowpress.Therearetwotypesofinner-camsystems:discrete
settinginner-camsandPosi-Lockinner-cams.
Discretesettinginner-camshavetheadjustmentscrewsgoingthroughaspecificholein
theinner-camandthreadingintothecam.Thescrewsneedtobecompletelyremoved
tomakeadjustments.The“A”settingisthelongestdrawlengthforthatbowanddraw
lengthsgetshorterasyouprogressthroughthealphabet(AtoB,BtoC,etc.)
PosiLockadjustableinner-cams
areadjustablein½”
drawlengthincrements.
The“A”settingisthelongest
settingforthecam.
Drawlengthsgetshorteras
youprogressthroughthealphabet
(“A”to“B”,“B”to“C”,etc.)by
roughly½”perletter.
SecondgenerationPosiLockinner-camsallowfordrawlengthadjustmentsin½”
incrementswithoutchanginginner-cams.Toadjustdrawlength,loosenthetwo8-32
buttonheadscrews2fullturns.Thiswillallowtheinner-camtobeliftedfarenoughto
disengagethepositioningpinandallowtheinner-camtorotatetoanewposition.Some
camsmayrequirethe8-32buttonheadscrewstomovetoalternatelocationstoreachthe
newdrawlengthadjustmentposition.Somedrawlengthadjustmentpositionsmaynotbe
accessiblewithoutputtingthebowinabowpress.Whenthenewdrawlengthadjustment
positionhasbeenachievedwiththeinner-cam,tightenthetwo8-32buttonheadscrews
andmovethedrawstoptothematchingsetting(“A”and“A”,“B”and“B”).
Incaseswherethereisaninner-camonboththetopandbottomcam,bothcamsmustbe
setinthesameletterpositionforthebowtotuneandshootproperly.Incaseswherethere
isaseparatedrawstop,thedrawstopmustbemovedtotheholemarkedwiththeletter
correspondingtotheinner-camsetting.
Compound Bow
USER’S GUIDE
StOP aDJUStmEntS:
DRaw StOP:
Thepositionofthedrawstopmustmatchthesettingontheinner-cam.Forexample,ifthecam
isseton“E”,thedrawstopmustbeplacedinoneofthedrawstopholesmarkedwithan“E”.
Iftheinner-camisinthe“B”setting,thestopmustbeinthe“B”position.Certainhybridcams
havetopandbottomstops.Theycanbeshotwithbothstopsforaharder“wall”orwithonly
thetopstopforasofter“wall”.Nevershoothybridcamswiththetwostopoptionwithonlythe
bottomstop.Ineithercase,thestopsneedtobeintheholesmarkedwiththesamemarkingas
theinner-camsetting.TheUltraFast(UF)hybridcamsystemhastwovalleysettings-longand
short.Whenusingtopandbottomstopsforahard“wall”bothstopsneedtobeinthesame
holedesignation-longorshort.
LEt-Off:
Let-offadjustmentispartofthedrawstop.Toadjustfromhighertolowerlet-off,remove
thedrawstopfromthehigherlet-offholeandreinstallitinthelowerlet-offholeofthe
correspondinginner-camsetting.Forexample,ifthecamissetin“E”thestopmustbe
reinstalledintheholemarked“E”intherowmarkedwiththelowerlet-offsetting.
Changingtolowerlet-offwillshortenthedrawlengthasmallamount.
Setting Bow Madness XL Bow Madness 3G Bow Madness XS Brute X Stinger 3G Chaos 1
A30 30 30 30 30 1/2 28
B29 1/2 29 1/2 29 1/2 29 1/2 30 27 1/2
C29 29 29 29 29 1/2 26 1/2
D28 1/2 28 1/2 28 1/2 28 1/2 29 25 3/4
E28 28 28 28 28 1/2 25
F27 1/2 27 1/2 27 1/2 27 1/2 28 24
G27 27 27 27 27 1/2
H26 1/2 26 1/2 26 1/2 26 1/2 27
I26 26 26 26 26 1/2
J25 1/2 25 1/2 25 1/2 25 1/2 26
K25 25 25 25 25 1/2
Setting
Dream
Season
EVO
EVO 7 EVO SD Vendetta Revenge Stiletto Freak Dominator Supra ME
A30 31 28 1/2 32 30 27 1/2 33 31 1/2 30
B29 1/2 30 1/2 28 31 1/2 29 1/2 27 32 1/2 31 29 1/2
C29 30 27 1/2 31 29 26 1/2 32 30 1/2 29
D28 1/2 29 1/2 27 30 1/2 28 1/2 26 31 1/2 30 28 1/2
E28 29 26 1/2 30 28 25 1/2 31 29 1/2 28
F27 1/2 28 1/2 26 29 1/2 27 1/2 25 30 1/2 29 27 1/2
G27 28 25 1/2 29 27 24 1/2 30 28 1/2 27
H26 1/2 27 1/2 25 28 1/2 26 1/2 24 29 1/2 28 26 1/2
I26 27 24 1/2 28 26 23 1/2 29 27 1/2 26
J25 1/2 26 1/2 24 27 1/2 25 1/2 23 28 1/2 27 25 1/2
K25 26 27 25 28
L26 1/2 24 1/2
10
11
StaGE 3™:
DRaw LEnGth:Thedrawlengthisadjustedbyplacingthebowinanappropriatebowpress
andrelievingthetensionfromthestringandcables.Movethestringtotheslotthat
willshortentheeffectivelengthofthestringtoshortenthedrawlengthby½”perwheel.Move
thestringtotheslotthatwilllengthentheeffectivelengthofthestringtolengthen
thedrawofthebowby½”perwheel.
PSE “fC” fLEXIBLE anD “OP” OPtI Cam InStRUCtIOnS:
TheFCcamsystemandtheOPcamsystemeachconsistof2camswithrotatinginner-cams
foradjustingdrawlength.Inaddition,thecamdesignhastwodrawweightsettings.Inthe
FixedPeakWeightsetting(seeFigure1)thepeakdrawweightstaysthesameregardlessof
thedrawlengthsetting.IntheGrowWithYousetting(seeFigure2)thepeakdrawweight
getslighterasthedrawlengthisadjustedshorter.Thecableiseasilypulledoverthe“Grow
withYou”bosspegtomaketheadjustmentfromfixedpeakweighttothe“GrowwithYou”
setting-orback.Nobowpressisrequiredforthisadjustment.
DRaw LEnGth aDJUStmEnt - PSE “fC”- fLEXIBLE Cam:
Theinner-camhasholesmarked“A”through“J”foradjustingdrawlength(seeFigure3)aswell
asasetofthreadedholesmarked“S”and“L”.The“L”holesareusedforlongerdrawlengths
andthe“S”holesareusedforshorterdrawlengths(seeFigure4).Seethetableforthesetting
requiredtoachievedifferentdrawlengthsandweight.
Tomakethenecessaryadjustment,removethescrewholdingtheinner-caminplaceandrotate
theinner-camsothelettersettingdesiredlinesupwiththethreaded“L”or“S”hole
inthecam.Replaceandtightenthescrew. IT IS IMPORTANT THAT BOTH TOP AND
BOTTOM CAMS BE ADJUSTED THE SAME.Theseadjustmentscanbemadeeitherwithor
withoutabowpress.
These two rows of holes
are used to determine
draw length.
“Fixed Peak
Weight” boss peg
Cable is pulled over
the boss and placed
in the groove for fixed
weight settings
Figure 1 Figure 3
PSE fC”- fLEXIBLE Cam aDJUStmEntS:
Figure 4
Figure 2
The “S” set of
threaded holes.
“Fixed Peak
Weight” boss
peg
Cable is routed behind
the boss for “Grow with
You” settings
The “L” set of
threaded holes.
Compound Bow
USER’S GUIDE
PSE mInI BURnERfC Cam aDJUStmEntS:
pse MINI BURNeR 20# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(6 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(6 turns off)
DRAW
LENGTH
DRAW
LENGTH
(6 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(6 turns off)
A-L
26 26 3/8 20
15 26 26 3/8
19
15
B-L
25 1/4 25 5/8 20
15 25 1/8 25 1/2
19
15
C-L
24 5/8 25 20
15 24 3/8 24 3/4 19 15
D-L
24 24 3/8 20
15 23 5/8 24 19 15
E-L
23 3/8 23 3/4 20
15 23 23 3/8 19 15
F-L
22 3/4 23 1/8 20
15 22 1/4 22 5/8 19 15
G-L
22 1/8 22 1/2 20
15 21 5/8 22 19 15
H-L
21 1/2 21 7/8 20
15 21 21 3/8 18 1/2 14
I-L
20 7/8 21 1/4 20
15 20 3/8 20 3/4 18 14
J-L
20 1/8 20 1/2 20
15 19 5/8 20 17 1/4 13
G-S
19 1/2 19 7/8 20
15 18 7/8 19 1/4 16 1/2 12 1/2
H-S
18 3/4 19 1/8 20
15 18 1/8 18 1/2 15 1/2 11 3/4
I-S
18 18 3/8 20
15 17 1/8 17 1/2 14 1/2 10 1/2
J-S
17 17 3/8 20
15 16 16 3/8 13 9
pse MINI BURNeR 29# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(6 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(6 turns off)
DRAW
LENGTH
DRAW
LENGTH
(6 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(6 turns off)
A-L
26 26 3/8 29
21 1/2 26 26 3/8
26
19
B-L
25 1/4 25 5/8 29
21 1/2 25 1/8 25 1/2
26
19
C-L
24 5/8 25 29
21 1/2 24 3/8 24 3/4 26 19
D-L
24 24 3/8 29
21 1/2 23 5/8 24 26 19
E-L
23 3/8 23 3/4 29
21 1/2 23 23 3/8 26 19
F-L
22 3/4 23 1/8 29
21 1/2 22 1/4 22 5/8 26 19
G-L
22 1/8 22 1/2 29
21 1/2 21 5/8 22 26 19
H-L
21 1/2 21 7/8 29
21 1/2 21 21 3/8 25 3/4 18 1/2
I-L
20 7/8 21 1/4 29
21 1/2 20 3/8 20 3/4 25 18
J-L
20 1/8 20 1/2 29
21 1/2 19 5/8 20 24 1/4 17 1/4
G-S
19 1/2 19 7/8 29
21 1/2 18 7/8 19 1/4 23 16
H-S
18 3/4 19 1/8 29
21 1/2 18 1/8 18 1/2 22 15 1/2
I-S
18 18 3/8 29
21 1/2 17 1/8 17 1/2 20 1/2 14
J-S
17 17 3/8 29
21 1/2 16 16 3/8 20 1/2 14
pse MINI BURNeR 40# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(6 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(6 turns off)
DRAW
LENGTH
DRAW
LENGTH
(6 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(6 turns off)
A-L
26 26 3/8 40
30 26 26 3/8
35
25
B-L
25 1/4 25 5/8 40
30 25 1/8 25 1/2
35
25
C-L
24 5/8 25 40
30 24 3/8 24 3/4 35 25
D-L
24 24 3/8 40
30 23 5/8 24 35 25
E-L
23 3/8 23 3/4 40
30 23 23 3/8 35 25
F-L
22 3/4 23 1/8 40
30 22 1/4 22 5/8 35 25
G-L
22 1/8 22 1/2 40
30 21 5/8 22 35 25
H-L
21 1/2 21 7/8 40
30 21 21 3/8 37 24 1/2
I-L
20 7/8 21 1/4 40
30 20 3/8 20 3/4 36 3/4 24
J-L
20 1/8 20 1/2 40
30 19 5/8 20 35 1/2 22 3/4
G-S
19 1/2 19 7/8 40
30 18 7/8 19 1/4 34 21 1/2
H-S
18 3/4 19 1/8 40
30 18 1/8 18 1/2 32 1/4 20 1/4
I-S
18 18 3/8 40
30 17 1/8 17 1/2 30 1/2 19
J-S
17 17 3/8 40
30 16 16 3/8 27 17 1/2
12
pse CHAOs FC 40# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
A-L
27 27 1/4 40
33 27 27 1/4
37
31
B-L
26 1/4 26 1/2 40
33 26 26 1/4
37
31
C-L
25 1/2 25 3/4 40
33 25 1/4 25 1/2 37 31
D-L
24 3/4 25 40
33 24 1/2 24 3/4 37 31
E-L
24 24 1/4 40
33 23 3/4 24 37 31
F-L
23 1/4 23 1/2 40
33 23 23 1/4 37 31
G-L
22 1/2 22 3/4 40
33 22 1/4 22 1/2 37 31
H-L
21 3/4 22 40
33 21 1/2 21 3/4 36 1/2 29
I-L
21 21 1/4 40
33 20 3/4 21 36 28
J-L
19 3/4 20 40
33 19 1/2 19 3/4 34 26 1/2
G-S
19 19 1/4 40
33 18 1/2 18 3/4 32 25
H-S
18 1/4 18 1/2 40
33 17 3/4 17 3/4 30 24
I-S
17 3/4 17 3/4 40
33 17 1/4 17 1/4 28 22
J-S
17 17 40
33 16 16 25 20
pse CHAOs FC 29# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
A-L 27 27 1/4 29 23 1/2 27 27 1/4 26 1/2 21 1/2
B-L 26 1/4 26 1/2 29 23 1/2 26 26 1/4 26 1/2 21 1/2
C-L 25 1/2 25 3/4 29 23 1/2 25 1/4 25 1/2 26 1/2 21 1/2
D-L 24 3/4 25 29 23 1/2 24 1/2 24 3/4 26 1/2 21 1/2
E-L 24 24 1/4 29 23 1/2 23 3/4 24 26 1/2 21 1/2
F-L 23 1/4 23 1/2 29 23 1/2 23 23 1/4 26 1/2 21 1/2
G-L 22 1/2 22 3/4 29 23 1/2 22 1/4 22 1/2 26 1/2 21 1/2
H-L 21 3/4 22 29 23 1/2 21 1/2 21 3/4 26 20 1/2
I-L 21 21 1/4 29 23 1/2 20 3/4 21 25 1/2 19 3/4
J-L 19 3/4 20 29 23 1/2 19 1/2 19 3/4 24 1/4 18 1/2
G-S 19 19 1/4 29 23 1/2 18 1/2 18 3/4 23 17 1/2
H-S 18 1/4 18 1/2 29 23 1/2 17 3/4 17 3/4 21 3/4 16 1/2
I-S 17 3/4 17 3/4 29 23 1/2 17 1/4 17 1/4 20 1/4 15 1/4
J-S 17 17 29 23 1/2 16 16 18 13 1/2
PSE ChaOSfC Cam aDJUStmEntS:
Chaos FC adjustments continued on next page
13
14
PSE ChaOSfC Cam aDJUStmEntS: (COntInUED)
pse CHAOs FC 60# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
A-L 27 27 1/4 60 46 27 27 1/4 53 42
B-L 26 1/4 26 1/2 60 46 26 26 1/4 53 42
C-L 25 1/2 25 3/4 60 46 25 1/4 25 1/2 53 42
D-L 24 3/4 25 60 46 24 1/2 24 3/4 53 42
E-L 24 24 1/4 60 46 23 3/4 24 53 42
F-L 23 1/4 23 1/2 60 46 23 23 1/4 53 42
G-L 22 1/2 22 3/4 60 46 22 1/4 22 1/2 53 42
H-L 21 3/4 22 60 46 21 1/2 21 3/4 52 40
I-L 21 21 1/4 60 46 20 3/4 21 50 39
J-L 19 3/4 20 60 46 19 1/2 19 3/4 48 1/2 37 1/2
G-S 19 19 1/4 60 46 18 1/2 18 3/4 46 1/2 36
H-S 18 1/4 18 1/2 60 46 17 3/4 17 3/4 44 33 1/2
I-S 17 3/4 17 3/4 60 46 17 1/4 17 1/4 40 30
pse CHAOs FC 50# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
DRAW
LENGTH
DRAW
LENGTH
(4 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(4 turns off)
A-L 27 27 1/4 50 40 27 27 1/4 46 36 1/2
B-L 26 1/4 26 1/2 50 40 26 26 1/4 46 36 1/2
C-L 25 1/2 25 3/4 50 40 25 1/4 25 1/2 46 36 1/2
D-L 24 3/4 25 50 40 24 1/2 24 3/4 46 36 1/2
E-L 24 24 1/4 50 40 23 3/4 24 46 36 1/2
F-L 23 1/4 23 1/2 50 40 23 23 1/4 46 36 1/2
G-L 22 1/2 22 3/4 50 40 22 1/4 22 1/2 46 36 1/2
H-L 21 3/4 22 50 40 21 1/2 21 3/4 45 1/2 35
I-L 21 21 1/4 50 40 20 3/4 21 44 1/2 33 1/2
J-L 19 3/4 20 50 40 19 1/2 19 3/4 42 1/2 32
G-S 19 19 1/4 50 40 18 1/2 18 3/4 40 1/2 30 1/2
H-S 18 1/4 18 1/2 50 40 17 3/4 17 3/4 39 29
I-S 17 3/4 17 3/4 50 40 17 1/4 17 1/4 36 27
J-S 17 17 50 40 16 16 31 1/2 24 1/2
pse-archery.cOM
ThePSEwebsitehasnumerous
resourcesffprthePSEowner
• ThelatestPSEproducts
• Productfeaturevideos
• Serialnumbersearch
• Onlineproductregistration
• TunechartsonPSEbows
from1991topresent
• Plusmuchmore!
15
Cable in the “Fixed Peak
Weight” setting
Cable in the “Grow with You” setting
pse RALLY 50# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(10 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(10 turns off)
DRAW
LENGTH
DRAW
LENGTH
(10 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(10 turns off)
A31 31 1/8 50 32 30 7/8 31 50 32
B30 1/2 30 5/8 50 32 30 3/8 30 1/2 50 32
C30 30 1/8 50 30 29 7/8 30 49 30
D29 1/2 29 5/8 50 30 29 3/8 29 1/2 49 29
E29 29 1/8 50 30 28 7/8 29 49 29
F28 1/2 28 5/8 50 30 28 3/8 28 1/2 48 29
G28 28 1/8 50 30 27 7/8 28 48 27
H27 1/2 27 5/8 50 29 27 1/4 27 3/8 48 27
I27 27 1/8 50 28 26 3/4 27 48 26
J26 1/2 26 5/8 50 27 26 1/8 26 1/4 47 26
K26 26 1/8 50 27 25 1/2 25 5/8 47 25
L25 1/4 25 3/8 50 26 25 25 1/4 47 25
M24 3/4 24 7/8 50 26 24 3/8 24 5/8 46 24
N24 24 1/8 50 26 23 7/8 24 1/8 45 23
O23 1/2 23 5/8 50 25 23 1/4 23 1/2 44 23
P23 23 1/8 50 25 22 3/4 22 7/8 43 22
Q22 1/2 22 5/8 50 25 22 1/8 22 1/4 42 22
R22 22 1/8 50 25 21 5/8 21 3/4 41 20
S21 1/2 21 5/8 50 25 21 21 1/4 39 19
T21 21 1/8 50 25 20 1/2 20 3/4 38 18
U20 1/2 20 5/8 50 25 19 7/8 20 1/8 36 17
V20 20 1/8 50 25 19 3/8 19 5/8 34 16
W19 1/2 19 5/8 50 25 18 3/4 19 32 16
X19 19 1/8 50 25 18 1/4 18 1/2 31 14
Cable is routed behind
the boss peg for “Grow
with You” settings
“Fixed Peak
Weight” boss
peg
DRAW LENGTH ADJUSTMENT - “OP” OPTI CAM:
Theinner-camhasholesmarked“A”through“X”foradjustingdrawlength.
Seethetableforthesettingrequiredtoachievedifferentdrawlengthsandweights.
Tomakethenecessaryadjustment,loosenthe8-32buttonheadscrewstwofullturns.
“A”isthelongestdrawlengthsettinganddrawlengthsgetshorterasyoumoveupthe
alphabet(“A”to“B”,“B”to“C”,etc.).TheOptiCaminner-camsadjustfrom“A”to“H”
andthenrequirethe8-32screwsberemovedandrepositionedtoadjustfrom“I”to“P”.
PSE RaLLYOP Cam aDJUStmEntS anD SEttInGS:
Rally adjustments continued on next page
Cable is pulled over
the boss peg and placed
in the groove for fixed
peak weight settings
16
pse RALLY 60# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(10 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(10 turns off)
DRAW
LENGTH
DRAW
LENGTH
(10 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(10 turns off)
A31 31 1/8 60 38 30 7/8 31 59 38
B30 1/2 30 5/8 60 38 30 3/8 30 1/2 59 37
C30 30 1/8 60 38 29 7/8 30 58 35
D29 1/2 29 5/8 60 38 29 3/8 29 1/2 58 35
E29 29 1/8 60 38 28 7/8 29 58 35
F28 1/2 28 5/8 60 38 28 3/8 28 1/2 58 35
G28 28 1/8 60 37 27 7/8 28 58 34
H27 1/2 27 5/8 60 36 27 1/4 27 3/8 58 32
I27 27 1/8 60 35 26 3/4 27 58 32
J26 1/2 26 5/8 60 34 26 1/8 26 1/4 57 31
K26 26 1/8 60 33 25 1/2 25 5/8 57 31
L25 1/4 25 3/8 60 31 25 25 1/4 57 31
M24 3/4 24 7/8 60 30 24 3/8 24 5/8 55 30
N24 24 1/8 60 30 23 7/8 24 1/8 54 29
O23 1/2 23 5/8 60 30 23 1/4 23 1/2 54 28
P23 23 1/8 60 30 22 3/4 22 7/8 52 27
Q22 1/2 22 5/8 60 30 22 1/8 22 1/4 51 26
R22 22 1/8 60 30 21 5/8 21 3/4 50 25
S21 1/2 21 5/8 60 30 21 21 1/4 48 24
T21 21 1/8 60 30 20 1/2 20 3/4 46 22
U20 1/2 20 5/8 60 30 19 7/8 20 1/8 44 21
V20 20 1/8 60 30 19 3/8 19 5/8 42 20
W19 1/2 19 5/8 60 30 18 3/4 19 39 20
X19 19 1/8 60 30 18 1/4 18 1/2 38 18
pse RALLY 70# MODeL
FIXED PEAK WEIGHT SETTINGS GROW WITH YOU SETTINGS
MODULE
SETTING
DRAW
LENGTH
DRAW
LENGTH
(10 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(10 turns off)
DRAW
LENGTH
DRAW
LENGTH
(10 turns off)
PEAK
DRAW
WEIGHT
DRAW
WEIGHT
(10 turns off)
A
31 31 1/8 70
45 30 7/8 31
68
44
B
30 1/2 30 5/8 70
45 30 3/8 30 1/2
68
43
C
30 30 1/8 70
45 29 7/8 30 68 43
D
29 1/2 29 5/8 70
45 29 3/8 29 1/2 68 42
E
29 29 1/8 70
44 28 7/8 29 68 42
F
28 1/2 28 5/8 70
44 28 3/8 28 1/2 68 42
G
28 28 1/8 70
43 27 7/8 28 68 40
H
27 1/2 27 5/8 70
42 27 1/4 27 3/8 67 39
I
27 27 1/8 70
41 26 3/4 27 67 38
J
26 1/2 26 5/8 70
40 26 1/8 26 1/4 67 38
K
26 26 1/8 70
40 25 1/2 25 5/8 66 37
L
25 1/4 25 3/8 70
39 25 25 1/4 66 37
M
24 3/4 24 7/8 70
38 24 3/8 24 5/8 65 36
N
24 24 1/8 70
37 23 7/8 24 1/8 64 35
O
23 1/2 23 5/8 70
37 23 1/4 23 1/2 62 34
P
23 23 1/8 70
37 22 3/4 22 7/8 61 32
Q
22 1/2 22 5/8 70
37 22 1/8 22 1/4 59 31
R
22 22 1/8 70
37 21 5/8 21 3/4 58 30
S
21 1/2 21 5/8 70
37 21 21 1/4 56 29
T
21 21 1/8 70
37 20 1/2 20 3/4 54 27
U
20 1/2 20 5/8 70
37 19 7/8 20 1/8 51 25
V
20 20 1/8 70
37 19 3/8 19 5/8 48 24
W
19 1/2 19 5/8 70
37 18 3/4 19 46 24
X
19 19 1/8 70
37 18 1/4 18 1/2 45 21
PSE RaLLYOP Cam aDJUStmEntS anD SEttInGS: (COntInUED)
17
X technOlOGy
TheXTechnologybowscomewithmanyuniquefeaturesthatwillenhance
yourarcheryexperience.
MAINTENANCE
Yourbowisamechanicaldevicethatissubjecttowearandthereforemustbeinspected
periodicallyandgiventheproperadjustmentsandservice.Itisrecommendedthatthis
servicebeperformedatleastonceayearbyanauthorizedPSEdealer.Allcomponents,
includingstring,cables,axles,e-clips,limbsandrisershouldbecarefullyinspectedfor
damageorwear.
STRINGS AND CABLES
Applyalightcoatofhighqualitybowstringwaxtoyourstringandcableeachtimeyou
shootyourbow.ItisespeciallyimportantNOTtowaxtheareaofthestringthatwraps
aroundtheidlerwheel.Thisareaofthestringshouldbetreatedwithacamlubricant.
Thiswillhelpreducewearonyourstringandcables.Inspectthestringandcablesregularly
andreplacethemwhenthereisevidenceofwear,every5000shotsorevery12months.
USING A BOW PRESS
ALLXTechnologybowsMUSTbeservicedinanapprovedbowpressandrequirespecial
consideration.Donotattempttoservicethesebowsinanybowpresswithoutreviewingthe
proceduresdescribedherein.
Useofanon-approvedbowpressorimproperuseofanapprovedbowpressWILLresult
indamagetothebowandpossiblepersonalinjury.Damagesincurredbyimproperuse
ormaintenancewillnotbecoveredunderthewarranty.SeethePSEwebsiteat
www.pse-archery.comforalistofapprovedbowpresses
Therearetwobasictypesofapprovedpressesavailable:compression-typeandpull-type.
COMPRESSION-TYPE BOW PRESS:
Thistypeofpresspushesinahorizontaldirectionagainstthetipsofthelimbs.
Noothersupportforthebowisrequired.
Whenusingapressofthistype,backeachlimbboltout4turnsfromthebottomsetting,
positionthebowinthepressandcrankpressinwardtoapplyacompressionforceagainst
thelimbtipsasshown.
COMPRESSION-TYPE BOW PRESS
X Technology continued on next page
Compound Bow
USER’S GUIDE
CompressONLYfarenoughtoloosenthe
stringandcables.Overcompressingcould
breakthelimbsandcausepersonalinjury.Any
damagesincurredfromover-compressingwill
notbecoveredunderwarranty.
PULL-TYPE PRESS:
Thistypeofpresspullstheriser
ofthebowinaverticaldirection
betweenrollersthatcompress
thelimbs.
Whenusingthistypepressitisvery
importanttopositiontherollersand
pressurepointscorrectly!
Backthelimbboltsout4turnsfromthebottomsetting
andpositionthepressurepointsontheriserascloseto
thelimbsaspossibleWITHOUTmakingcontactwiththe
limbsasshowninthephoto.Thepressurepointsmust
notcontactthelimbsatanytimeduringservicing.
 Positionthelimbrollersoutwardonthelimbssothatwhentheriserispulleddown
 thebowdoesnotslipthrough/betweentherollersbeforereleasingtensiononthe
 stringandcables.Therollersmustbeatleast4”fromthelimbpocketsorthelimbs
willbreak.Whileplacingtensiononthelimbs,BE VERY CAREFUL NOT TO PULL THE RISER
DOWN TOO FAR. DEFLECT THE LIMBS JUST ENOUGH TO REMOVE THE STRING AND
CABLES. Neverallowtherollerstogopasttheendofthelimbbelly(thinnestpart).
Servicesuchaspeepandstringmountedvibrationdamperinstallationandstringreplacement
canbeperformedwithaPocketPressportablebowpressavailablefromyourlocalPSEdealer.
Item#01031,#01164.#01165,#01169,#01170,#01184,#01185,#01186,#01187,
and#01188arepocketpressesavailableforalternateaxle-to-axlelengthsandcamtypes.
X technOlOGy (cOntinueD)
PULL-TYPE BOW PRESS
18
SERvICInG BOwS wIth PSE Uf CamS (PSE OmEn PRO)
CAUTION • CAUTION • CAUTION!
WhenservicingbowswithPSEUFcams,suchastheOMEN
PRO,itisimportant
touseabowpressthathasenoughclearanceforthecams.
Onsomebowpressesthecamsmaymakecontactwiththe
areashowninFigure1whencompressingthelimbs.Watch
verycarefullyasthebowiscompressed.Ifeithercamcomes
incontactwiththebowpress,STOP IMMEDIATELY or per-
manent
damage to bow components may occur.
Contactthebowpressmanufacturerforfurtherinformation. Figure 1
Cam may
hit here
19
pse liMiteD lifetiMe warranty
all pse ManufactureD BOws / accessOries / kinG prODucts
EachPSEBowisbackedbyaPSELimitedLifetimeWarrantytotheoriginal
ownerforthelifeoftheproduct.Productwillbereplacedorrepairedtorestore
ittoitsoriginalperformance.Cables,strings,orwearableitemsarenotcovered
bythiswarranty.
Evidenceofabuse,mishandling,misuse,oralterationtoanyPSEproductvoids
anyclaimtowarranty.
PSEspecificationsonstringsandharnessesmustbeadheredto.
PSEcannotbeheldresponsibleforinjuryorproductfailureresultingfrom
improperuseorneglectofmaintenance.
Allbowsmustundergostringandcablechangesevery5,000shotsorevery
12monthstomaintainPSEwarrantycoverage.Totalarrowweightmustbein
accordancewiththeguidelinespublishedbytheArcheryTradeAssociation(ATA)
forminimumarrowweight/bowpeakweight.OverstressingPSEcompoundbows
byusingarrowslighterthanATAguidelinewillvoidwarrantyandmaycause
damagetotheboworinjurytotheshooter.
PSEmakesnootherclaimseitherexpressedorimplied.Intheinterestofproduct
improvementandconsumersafety,PSEreservestherighttomakechangesin
productdesign,color,andspecificationswithoutnotice.
pse patent infOrMatiOn
Manufactured Under Patents: Licensed Under Patents:
5,301,651
5,335,644
5,339,790
5,365,650
5,377,658
5,469,834
5,487,373
5,495,843
5,507,270
5,657,739
5,678,529
5,762,060
5,960,778
6,112,732
6,176,231
6,360,735
6,792,930
6,889,683
6,968,837
7,347,196 B1
RE36,942
D429,309
D503,958
D528,625
7,699,045
7,721,721
7,784,452
5,392,756
5,501,208
5,505,185
5,749,351
5,894,835
5,921,227
6,237,584
6,588,411
6,966,314
7,832,388
7,891,349
7,918,218
7,980,236
7,980,237
20
Intheeventthedecalorthe
hatyouareorderingisno
longeravailable,theproduct
willbesubstitutedwitha
differentitem.
OffergoodintheUnited
Statesonly.
THANK YOU FOR
SELECTING PSE
Act now on this
one-time offer:
Purchase a PSE DECAL and receive
a FREE PSE cap!
CAP STYLE SHOWN MAY VARY
®
PSE GEL STICKER
(12” x 7”)
#41630
ExPERIEnCE. PERfoRmanCE.
wIndow dECaL
17” wide dieCUT vinyl #41647
PSE moSSY oaK®
TREESTand®
#45354
structured
low profile
OR
GET A FREE
PURCHASE
Use the order form on the next page to place your order.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

PSE Archery 2012 Bow User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI