Compound Bow
USER’S GUIDE
PAGE
1
compound bow user’s guide
PRECISION SHOOTING EQUIPMENT INC.
2727 N. FAIRVIEW AVE. TUCSON, AZ 85705 • PSE-ARCHERy.COM
PN: 80699
Thank you for choosing pse!
PAGE
2
pse compound bow owner’s information
Fill in the following information for your personal records.
Bow Model
Bow Serial Number:
See page 43 for the serial number location on your bow.
Purchased From:
Purchase Date:
Draw Length Draw Weight
Thank you from the entire PSE family for purchasing a PSE bow!
Your bow was manufactured from the finest materials available and
handcrafted with pride in the USA. With proper care you will enjoy the
use of this product for years to come.
Please read this entire booklet before shooting or adjusting your bow.
Remember, many adjustments to a compound bow require the use of a
bow press. Whenever shooting a bow, be certain of your target as well as
what else lies down range.
NOTE: IMPORTANT WARRANTY REGISTRATION INFORMATION IS ON PAGE 43
Thank You!
Compound Bow
USER’S GUIDE
PAGE
3
index
SUBJECT PAGE
Welcome to PSE and general product information .......................................... 4
Compound bow terminology ............................................................................ 5
PSE cable configurations .................................................................................... 6
PSE X-Tech bow press info ............................................................................. 7-9
Installation of accessories .................................................................................10
Other adjustments ...........................................................................................10
Setting up your bow .........................................................................................11
Flexslide™ installation and adjustments ..........................................................12
BackStop™ 2 installation and adjustments ..................................................... 12
Sting Stop™ installation and adjustments .......................................................13
Limb bands and cable guard dampers ......................................................... 14
Changing the FlexSlide rod .............................................................................15
PSE asymmetric idler ........................................................................................15
Cam adjustments .............................................................................................16
Draw stop information ..................................................................................... 17
Limb stop adjustments .................................................................................... 17
PSE Pro Series bows- draw setting charts .......................................................18
PSE Mainline bows- draw setting charts .........................................................19
PSE Morph™cam information .........................................................................21
PSE Surge™with Morph™cam settings charts ...........................................22-23
PSE Fever™One with Morph cam settings charts .....................................24-25
PSE Vision™cam information ...........................................................................27
PSE Vision™ with Vision™ “performance” cam setting charts .................28-29
PSE Vision™ with Vision™ “grow with you” cam setting charts ............... 30-31
PSE Fever™ with Vision™ “performance” cam setting charts ..................32-33
PSE Fever™ with Vision™ “grow with you” cam setting charts ................ 34-35
PSE Mini Burner™ XT with Vision™ “performance” setting charts ........... 36-37
PSE Mini Burner™ XT with Vision™ “grow with you” setting charts .........38-39
PSE limited lifetime warranty information ...................................................42
PSE warranty registration ............................................................................. 43
Thank You!
PAGE
4
Compound Bow
USER’S GUIDE
General operatinG instructions
• Always inspect your bow thoroughly before each shooting session to insure that it is in good
working order. Check for worn, loose or missing components and have them replaced at an
authorized PSE dealer as required, i.e. bushings, spacers, etc.
• Inspect your arrows to insure that they are straight, undamaged and that each nock is in good
condition. A cracked nock can break when fired from the bow and cause the bow to “dry fire”
resulting in possible injury to the archer and damage to the bow. Dry-firing is drawing and
releasing the bowstring without an arrow on the string.
• When purchasing arrows for your bow, consult the selection chart from the arrow manufacturer
and select the correct arrow for your application. Always use an arrow that is at least 5 grains per
pound of peak bow weight. Failure to do so could cause personal injury and damage to your bow.
bow maintenance
Your PSE bow will give you many years of use if maintained and cared for properly.
It is a mechanical device that is subject to wear and therefore must be inspected periodically and
given the proper adjustments and service. It is recommended that this service be performed at least
once a year by an authorized PSE dealer. All components, including string, cables, axles, e-clips,
limbs and riser should be carefully inspected for damage or wear.
STRINGS AND CABLES
Apply a light coat of high quality bowstring wax to your string and cable each time you shoot your
bow. It is especially important NOT to wax the area of the string that wraps around the idler wheel.
This area of the string should be treated with a cam lubricant. This will help reduce wear on your
string and cables. Inspect the string and cables regularly and replace them when there is evidence of
wear, every 5000 shots or every 12 months.
I
MPORTANT: Before servicing any PSE bow in a bow press, back out each limb
bolt the maximum number of turns from bottom.
• Keep synthetic cables and strings waxed. Apply bow string wax to your synthetic cables and string
before each shooting session.
• Strings and cables must be replaced periodically. A worn cable or string can suddenly break
causing serious injury to the archer and damage to the bow. It is recommended that the string
and cables be replaced at least every 5,000 shots or 12 months.
PSE recommends that this work be performed by an authorized PSE dealer.
• Always store your bow in a cool dry place. High temperatures, such as those that can occur in
the interior of a vehicle, can cause serious damage to your bow.
• After use in high humidity or damp conditions, wipe metal components of your bow
with a light oil.
safety
As with any weapon, safe operation of your PSE bow must always be the highest priority.
ALWAYS WEAR SAFETY GLASSES WHEN HANDLING A BOW.
Do not attempt to use your bow without proper instruction.
Doing so can result in serious injury.
a. NEVER DRY-FIRE YOUR BOW. Dry-firing is drawing and releasing the bowstring without an
arrow on the string. Dry-firing will likely cause damage to the bow and serious injury to the
archer. In the event of a dry-fire, have an authorized PSE dealer inspect the bow
for damage.
b. Always be sure of your intended target as well as what lies behind the target area. An arrow can travel
a considerable distance, so it is important to have a safe and sound backstop.
c. If you draw a bow and need to let it down, do so in a slow and careful manner. Keep your
support arm straight and prepare for a rapid and violent let-down. Avoid hitting your hand on
protruding accessories such as the cable guard or quiver. Keep your head and face back and
out of danger during let-down. Never draw a bow with a peak weight above your comfort level.
Always use a wrist sling when drawing a bow.
d. Never modify any part of the bow or its components by drilling extra holes or removing material.
This voids the warranty and presents safety problems.
e. It is not recommended to time the bow using a draw board unless the draw board is operated by
a winch or other mechanical pulling device.
compound bow terminoloGy
Compound Bow
USER’S GUIDE
PAGE
5
LIMB
TOP
LIMB
BOLT
SIGHT
ARROW
REST
GRIP
STABILIZER
TOP CAM
(HYBRID DUAL CAM MODELS)
or IDLER WHEEL
(SINGLE CAM MODEL- SHOWN)
BOW QUIVER
HOOD AND FOAM
CABLE
GUARD ROD
CABLE
SLIDE
BOW
SLING
BACKSTOP™2* (SHOWN)
OR STINGSTOP™*
RISER
BOTTOM CAM
TOP LIMB
POCKET
compound bow terminoloGy
AXLE
BOTTOM
LIMB BAND
VANE
OR
FLETCHING
NOCK
TOP
LIMB
BAND
BOTTOM
LIMB BOLT
CABLE GUARD
DAMPER
ARROW
* = DEPENDS ON BOW MODEL
QUIVER BRACKET
AND QUICK-MOUNT*
SIGHT
PINS
ARROW SHELF
TUNING
ALIGNMENT MARK
ARROW CLIP
BOTTOM
LIMB
AXLE
DRAW STOP
PEEP
SIGHT
TUBE
BACKSTOP™*
ADJUSTMENT
SCREWS
CABLE GUARD
ADJUSTMENT SCREW
MODULE
POSITION HOLES
BOTTOM
LIMB
POCKET
PAGE
6
Compound Bow
USER’S GUIDE
COMPRESSION-TYPE BOW PRESS
one cam bow
hybrid cam bow
cable confiGurations
two cam bow
STRING
STRING
BUSS CABLE
STRING
BUSS
CABLE
CONTROL
CABLE
CONTROL
CABLE
BUSS
CABLE
STRING
STRING
BUSS
CABLE
BUSS
CABLE
STRING
BUSS
CABLE
BUSS
CABLE
top cam
bottom cam
BUSS CABLE
STRING
STRING
idler wheel
top cam
bottom cam
bottom cam
Compound Bow
USER’S GUIDE
PAGE
7
pse x technoloGy
PSE X Technology bows come with many unique features that will enhance your
archery experience.
USING A BOW PRESS WITH X TECHNOLOGY BOWS
ALL PSE X Technology bows MUST be serviced in an approved bow press and require special
consideration. Do not attempt to service these bows in any bow press without reviewing the
procedures described herein.
Use of a non-approved bow press or improper use of an approved bow press WILL result
in damage to the bow and possible personal injury. Damages incurred by improper use
or maintenance will not be covered under the warranty. See the PSE website at
www.pse-archery.com for a list of approved bow presses.
There are two basic types of approved presses available: compression-type
and pull-type. (Pg8)
COMPRESSION-TYPE BOW PRESS:
This type of press pushes in a horizontal direction against the tips of the limbs.
No other support for the bow is required.
When using a press of this type, back each limb bolt out the maximum number of turns
indicated on your bow’s hang tag. Position the bow in the press and crank press inward to
apply a compression force against the limb tips as shown below.
COMPRESS ONLY FAR ENOUGH TO LOOSEN THE STRING AND CABLES.
OVER COMPRESSING COULD BREAK THE LIMBS AND CAUSE PERSONAL
INJURY.
ANY DAMAGES INCURRED FROM OVER-COMPRESSING WILL NOT BE
COVERED UNDER WARRANTY.
X Technology continued on next page
COMPRESSION-TYPE BOW PRESS
one cam bow
hybrid cam bow
cable confiGurations
two cam bow
PAGE
8
Compound Bow
USER’S GUIDE
PULL-TYPE BOW PRESS:
This type of press pulls the riser of the bow in a vertical direction between
rollers that compress the limbs.
When using this type press it is very important to position the rollers and
pressure points correctly! See illustration above.
Back each limb bolt out the maximum number of turns indicated on your bow’s hang tag
and position the pressure points on the riser as close to the limbs as possible WITHOUT
making contact with the limbs as shown in the photo below.
THE PRESSURE POINTS MUST NOT CONTACT THE
LIMBS AT ANY TIME DURING SERVICING.
pse x technoloGy USING A BOW PRESS
PULL-TYPE BOW PRESS
PULL-TYPE BOW PRESS
X Technology continued on next page
Compound Bow
USER’S GUIDE
PAGE
9
pse x technoloGy USING A BOW PRESS
SERVICING BOWS WITH PSE FT CAMS (PSE FULL THROTTLE™)
CAUTION • CAUTION • CAUTION!
When servicing bows with PSE FT cams, such as the
Full Throttle™, it is important to use a bow press
that has enough clearance for the cams.
On some bow presses the cams may make
contact with the area shown in Figure 1 when
compressing the limbs. Watch very carefully as the
bow is compressed. If either cam comes in contact
with the bow press, STOP IMMEDIATELY
or permanent damage to bow
components may occur.
Contact the bow press manufacturer for
further information. Figure 1
Cam may
hit here
Position the limb rollers outward on the limbs so that when the riser is pulled down
the bow does not slip through/between the rollers before releasing tension on the
string and cables. The rollers must be at least 4” from the limb pockets or the limbs
will break. While placing tension on the limbs, BE VERY CAREFUL NOT TO PULL THE RISER
DOWN TOO FAR. DEFLECT THE LIMBS JUST ENOUGH TO REMOVE THE STRING AND
CABLES. Never allow the rollers to go past the end of the limb belly (thinnest part).
Service such as peep and string mounted vibration damper installation and string replacement
can be performed with a “Pocket Press” portable bow press available from your local PSE
dealer. These pocket presses are available for alternate axle-to-axle lengths and cam types.
pse x technoloGy USING A BOW PRESS (Continued)
PAGE
10
Compound Bow
USER’S GUIDE
Your Authorized PSE Dealer is supplied with technical information on PSE bows
and cams. Please see your Dealer for assistance when making these adjustments.
installation of accessories
Arrowrest/Overdraw: The arrowrest or overdraw should be
installed according to the instructions received with the product.
It is usually mounted to the riser in the threaded hole on the
side opposite the shelf (Hole “A”) using the hardware provided
with the arrowrest or overdraw.
Sight: The sight should be installed according to the instructions
received with the product. It is usually mounted to the riser in
the threaded holes (Holes “B”) on the side opposite the shelf
using the hardware provided with the sight. Some bows are
equipped with multiple sight mounting holes which allow the
sight to be moved up or down.
Stabilizer: The stabilizer should be mounted according to the
manufacturer’s recommendation. It is usually mounted in the
threaded hole on the front of the riser (Hole “C”).
Bow Sling: The bow sling attaches to the riser of the bow
generally with the stabilizer. If a stabilizer is not used, attach the
sling to the riser with the correct sized bolt (5/16” - 24) using
the hole provided for the stabilizer (Hole “C”).
other adjustments
Draw Weight: Your bow is factory-set to within 2 lbs.
of the peak draw weight indicated on the bow hang tag and the
last 2 digits of the serial number. Changes in draw weight can
be made by turning the limb bolt in or out. Before making any
changes in weight, turn the limb bolt clockwise to the bottom
position. Never use extreme torque when turning the bolt or
damage to the limb may occur. The limb bolt may then be
turned counterclockwise to obtain the desired weight, but NEVER
more than the number of turns indicated on the hang tag.
Adjust each limb exactly the same. (See note and Fig. A below)
Hole
A
Holes
B
Hole
C
CAUTION: On some bow models,
the limb bolt locking screw, limb
support screws or pocket tang
locking screw MUST be loosened
BEFORE adjusting.
Pocket tang
locking screw
Limb
support
screw
Fig. A
Limb
bolt
Compound Bow
USER’S GUIDE
PAGE
11
settinG-up your bow
nockinG point placement:
Finger shooters: Install the nocking point so that the arrow
passes the center of the arrow rest mounting hole and
runs slightly point-down relative to the tuning mark on the
window of the bow.
Release Aid shooters: Install the nocking point so that the
arrow passes the center of the arrow rest mounting hole
and runs parallel to the alignment mark on the window of
the bow.
arrow rest adjustment:
When shooting with a release aid, the in/out position
of the arrow rest should be adjusted so that the arrow
runs parallel with the tuning mark on the shelf when
viewed from above. When shooting with fingers the
arrow should point slightly outside the tuning alignment
mark on the shelf.
NOTE: Tuning alignment marks are for reference only.
Adjustments will likely be necessary to nocking point
and in/out position during tuning
siGht adjustment:
When adjusting the sight pin locations, always remember
to “follow the group”. That is, if the shot group is to the
left of the target, move the sight pins to the left. If the shot
group is low, move the sight pins down.
cable Guard adjustment
and installation:
Install the cable guard as shown in
Figure A. Adjust the cable guard so the
cables just clear the arrow vanes. On bows
using an offset cable guard rod, adjustments
must be done with the rod in the up position
(approximately 2 o’clock) as shown in
Figure B (10 o’clock for left handed bows).
Over-rotating an adjustable cable guard
creates excessive arrow clearance and may
cause the cable to track incorrectly on the
wheels and cause personal injury and/or
damage to the bow.
Figure A Figure B
Tuning
Mark
Arrow rest mounting hole
••
•
Alignment
Mark
Tuning
Mark
Holes
B
PAGE
12
Compound Bow
USER’S GUIDE
1. Remove the set screws from the base using a T8 Torx wrench.
2. Install the Backstop™ 2 into the threaded hole below the
grip on the string-facing side of the bow.
3. Extend the Backstop™ 2 until it makes contact with the string. Mark the string ¼”
above and ¼” below where it makes contact with the string. Remove the Backstop™ 2
and add serving to that area of the string. Reinstall the Backstop™ 2.
4. Securely tighten the base to the bow handle.
6. Extend rod from base. Install the set screws to secure rod in this position.
Tighten set screws. It is desired to have some clearance (approximately 1/16”) between
the bumper and the bowstring at brace.
7. Rotation instructions- Adjust the Backstop™ 2 to the desired position and tighten the
rotator screw. The Backstop™ 2 design allows for the bumper to be positioned so the
string strikes the center of the bumper. It is desired to have some clearance
(approximately 1/16”) between the bumper and the bowstring at brace.
backstop™2 instructions
Serve string
in this area.
Set screws
Alignment
holes
flexslide™installation and adjustment
FlexSlide
Washer with
Alignment Tabs
Lateral
Adjustment
Screw
FlexSlide
Pivot with
Alignment
Tabs
FlexSlide
Limb
Low Friction
FlexSlide Rod
Note: Many PSE bow models come from the factory with the Backstop™ 2 installed.
These instructions refer to reinstallation or adjustment if needed after making adjustments
to your PSE bow.
The PSE FlexSlide™ cable guard system is based on the same advanced
design and analysis used to create PSE Limbs. The flex-tuned design
and adjustable offset are engineered to create more consistent lateral
loads through the draw cycle and improve bow accuracy.
1. The standard factory setting adjusts the
FlexSlide™ to its bottom position for maximum
arrow clearance.
2. To adjust the lateral position, turn the
adjustment screw counterclockwise to
reduce arrow clearance or clockwise to
increase arrow clearance.
3. After making adjustments to your
FlexSlide™, check both arrow clearance
and BackStop™ clearance. When drawing
the bow, the buss cable should never
contact the arrow shaft or any part of
the Backstop™.
4. If any contact exists, tighten the
adjustment screw to create adequate
clearance. One full turn on the adjustment
screw will move the slide approximately 1/8”.
NOTE: Lateral adjustments to the FlexSlide™
may affect arrow tuning.
At rest At full-draw
Compound Bow
USER’S GUIDE
PAGE
13
FlexSlide
Washer with
Alignment Tabs
Lateral
Adjustment
Screw
Note: Many PSE bow models come from the factory with the Backstop™ 2 installed.
These instructions refer to reinstallation or adjustment if needed after making adjustments
to your PSE bow.
Note: Some PSE bow models come from the factory with the PSE Sting Stop™
Backstop installed. These instructions refer to reinstallation or adjustment if
needed after making adjustments to your PSE bow.
1. Thread the Sting Stop™nut all the way up toward the bumper of
the Sting Stop™ rod.
2. Thread the Sting Stop™rod into the threaded hole below the grip on the
riser. The bowstring will need to be displaced slightly to one side to thread
the rod into the bow.
3. Unscrew the Sting Stop™until the rubber bumper approaches the bowstring.
Mark the string 1/4” above the rubber bumper in its highest position and
1/4” below the bumper in its lowest position. Remove the Sting Stop™ and
add serving to the marked area of the string. Reinstall the Sting Stop™.
4. Adjust the Sting Stop™to the desired position and tighten the Sting Stop™
nut against the riser. The Sting Stop™ design allows for the bumper to
be positioned so the string strikes the center of the bumper. It is desired
to have some clearance (approximately 1/16”) between the bumper and
the bowstring at brace. It is preferred to have the Sting Stop™rod in the
up position if possible, but may not be possible in order to achieve the
necessary clearance and contact point.
stinG stop™ instructions
Serve string
in this area.
PAGE
14
Compound Bow
USER’S GUIDE
installinG limb bands and cable Guard damper
Limb Band on
Solid Limb
Cable Guard Damper
If your bow is equipped with a Cable Guard Damper it should be even with
the cable slide when the bow is at rest. More than one Cable Guard Damper
can be used.
If your solid limb bow is equipped with limb bands, the proper placement of the
bands is approximately 1/8” beyond the limb fork.
If your split limb bow is equipped with limb bands, the proper placement of the
bands is at least 1/4” away from the cam (align the band with the end of
the limb graphic).
Limb Bands across
Split Limb
Limb Bands on
Split Limb (one per limb)
Limb Band Damper Cable Guard Damper
check out our line of briGht colored rubber
Your PSE dealer carries a full line of colored rubber
add-ons for your PSE bow. Choose from pink,
orange, yellow, blue, purple, black, red and
lime green.
Compound Bow
USER’S GUIDE
PAGE
15
If you are replacing a PSE Flex slide rod or changing
to a different color follow these instructions.
FIGURE 1:
Unsnap the two strings from the cable slide- noting
the orientation of the two different clips (shorter clip
closest to the riser)
FIGURE 2:
Slide the cable slide off the Flex slide
FIGURE 3:
Using a T9 torx wrench remove the two screws.
Replace with the new Flex slide rod and tighten
the screws.
Re-assembly is the reverse of the
instructions above.
installinG limb bands and cable Guard damper
pse asymmetric idler
Wide edge
Limb Bands on
Split Limb (one per limb)
PSE single cam bows are equipped with a special
asymmetric idler wheel, which is assembled on the
top limb. It is essential that the idler be
oriented properly.
The wide edge of the idler always goes to the
cable guard side of the bow.
The illustration shows the proper orientation of
the idler for a right-handed bow when viewed while
holding the bow as it is shot.
Cable Guard Damper
check out our line of briGht colored rubber
chanGinG the flex slide rod
PAGE
16
Compound Bow
USER’S GUIDE
cam adjustments
WHEELS/CAMS: Many PSE wheels and cams have adjustable features. Each one comes from
the factory set up and ready to use but there may be occasions that you need to adjust the
characteristics of your bow. In some cases you will need a PSE Tune Chart to determine what
to adjust, and you may need to see a PSE Dealer for information. If you are not sure of the
adjustment you are making, stop and see your PSE Dealer for assistance. In some cases, an
appropriate bow press will be needed to make adjustments to cams and wheels. If you do not
have an appropriate press, see your PSE Dealer.
CAM ORIENTATION:
On cams with orientation marks, a reference mark is found to indicate an approximate
orientation. This line is for reference only and is meant to give approximate orientation
only and may vary between bow models. The orientation of the cams may be changed slightly
by twisting or untwisting the string or cables.
ALL INNER-CAMS:
The inner-cam system allows draw length adjustments over a prescribed range usually without
putting the bow in a bow press. There are two types of inner-cam systems: discrete setting
inner-cams and Posi-Lock inner-cams.
Discrete setting inner-cams have the adjustment screws going through a specific hole in the
inner-cam and threading into the cam. The screws need to be completely removed to make
adjustments. The “A” setting is the longest draw length for that bow and draw lengths get
shorter as you progress through the alphabet (A to B, B to C, etc.)
Posi-lock adjustable inner-cams are adjustable in ½” draw length increments. The “A” setting is
the longest setting for the cam. Draw lengths get shorter as you progress through the alphabet
(“A” to “B”, “B” to “C”, etc.) by roughly ½” per letter.
Second and third generation Posi-lock inner-cams
allow for draw length adjustments in ½” increments
without changing inner-cams. To adjust draw length,
loosen the two 8-32 button head screws two full
turns. This will allow the inner-cam to be lifted far
enough to disengage the positioning pin and allow
the inner-cam to rotate to a new position. Some
cams may require the 8-32 button head screws to
move to alternate locations to reach the new draw
length adjustment position. Some draw length
adjustment positions may not be accessible without
putting the bow in a bow press. When the new
draw length adjustment position has been achieved
with the inner-cam, tighten the two 8-32 button
head screws and move the draw stop to the
matching setting (“A” and “A”, “B” and “B”).
In cases where there is an inner-cam on both the top and bottom cam, both cams must be
set in the same letter position for the bow to tune and shoot properly. In cases where there
is a separate draw stop, the draw stop must be moved to the hole marked with the letter
corresponding to the inner-cam setting.
Positioning Pin
INFORMATION ON DRAW STOP ADJUSTMENTS:
The position of the draw stop must match the setting on the inner-cam. For example, if the cam is set on “E”, the draw
stop must be placed in one of the draw stop holes marked with an “E”. If the inner-cam is in the “B” setting, the stop
must be in the “B” position. Certain hybrid cams have top and bottom stops. They can be shot with both stops for a
harder “wall” or with only the top stop for a softer “wall”. Never shoot hybrid cams with the two stop option with only the
bottom stop. In either case, the stops need to be in the holes marked with the same marking as the inner-cam setting.
limb stop adjustments
On bows equipped with a limb stop and cable stop, use of the limb stop is optional. If
choosing not to use the limb stop it may be removed or set in the longest “A” position so
that it does not contact the limb before the cable stop. Engraving for limb stop positions is
approximate and for reference only. Many factors will cause changes to the optimum limb
stop position.
OPTION 1: (If a safe method of holding the bow at full draw is available) Set Limb Stop to
the Longest “A” Location and time bow to cable stops at desired draw length as shown in
Figure 1. Using a safe method to hold the bow at full draw adjust limb stop so it contacts
the limb as shown in Figure 2.
OPTION 2: Set Limb Stop to the Longest “A” Postition. Time bow to cable stops at desired
draw length.Set Limb stop to the corresponding stop position. Draw bow with an arrow and
observe whether the cable stop or Limb Stop contacts first. Make small adjustments to the
Limb Stop position and recheck until it contacts at
the same time as the cable stop.
8-32 Button Head Screw
Compound Bow
USER’S GUIDE
PAGE
17
cam adjustments
WHEELS/CAMS: Many PSE wheels and cams have adjustable features. Each one comes from
the factory set up and ready to use but there may be occasions that you need to adjust the
characteristics of your bow. In some cases you will need a PSE Tune Chart to determine what
to adjust, and you may need to see a PSE Dealer for information. If you are not sure of the
adjustment you are making, stop and see your PSE Dealer for assistance. In some cases, an
appropriate bow press will be needed to make adjustments to cams and wheels. If you do not
have an appropriate press, see your PSE Dealer.
CAM ORIENTATION:
On cams with orientation marks, a reference mark is found to indicate an approximate
orientation. This line is for reference only and is meant to give approximate orientation
only and may vary between bow models. The orientation of the cams may be changed slightly
by twisting or untwisting the string or cables.
ALL INNER-CAMS:
The inner-cam system allows draw length adjustments over a prescribed range usually without
putting the bow in a bow press. There are two types of inner-cam systems: discrete setting
inner-cams and Posi-Lock inner-cams.
Discrete setting inner-cams have the adjustment screws going through a specific hole in the
inner-cam and threading into the cam. The screws need to be completely removed to make
adjustments. The “A” setting is the longest draw length for that bow and draw lengths get
shorter as you progress through the alphabet (A to B, B to C, etc.)
Posi-lock adjustable inner-cams are adjustable in ½” draw length increments. The “A” setting is
the longest setting for the cam. Draw lengths get shorter as you progress through the alphabet
(“A” to “B”, “B” to “C”, etc.) by roughly ½” per letter.
Second and third generation Posi-lock inner-cams
allow for draw length adjustments in ½” increments
without changing inner-cams. To adjust draw length,
loosen the two 8-32 button head screws two full
turns. This will allow the inner-cam to be lifted far
enough to disengage the positioning pin and allow
the inner-cam to rotate to a new position. Some
cams may require the 8-32 button head screws to
move to alternate locations to reach the new draw
length adjustment position. Some draw length
adjustment positions may not be accessible without
putting the bow in a bow press. When the new
draw length adjustment position has been achieved
with the inner-cam, tighten the two 8-32 button
head screws and move the draw stop to the
matching setting (“A” and “A”, “B” and “B”).
In cases where there is an inner-cam on both the top and bottom cam, both cams must be
set in the same letter position for the bow to tune and shoot properly. In cases where there
is a separate draw stop, the draw stop must be moved to the hole marked with the letter
corresponding to the inner-cam setting.
Positioning Pin
INFORMATION ON DRAW STOP ADJUSTMENTS:
The position of the draw stop must match the setting on the inner-cam. For example, if the cam is set on “E”, the draw
stop must be placed in one of the draw stop holes marked with an “E”. If the inner-cam is in the “B” setting, the stop
must be in the “B” position. Certain hybrid cams have top and bottom stops. They can be shot with both stops for a
harder “wall” or with only the top stop for a softer “wall”. Never shoot hybrid cams with the two stop option with only the
bottom stop. In either case, the stops need to be in the holes marked with the same marking as the inner-cam setting.
Draw Stop
Draw Stop
Screw
limb stop adjustments
On bows equipped with a limb stop and cable stop, use of the limb stop is optional. If
choosing not to use the limb stop it may be removed or set in the longest “A” position so
that it does not contact the limb before the cable stop. Engraving for limb stop positions is
approximate and for reference only. Many factors will cause changes to the optimum limb
stop position.
OPTION 1: (If a safe method of holding the bow at full draw is available) Set Limb Stop to
the Longest “A” Location and time bow to cable stops at desired draw length as shown in
Figure 1. Using a safe method to hold the bow at full draw adjust limb stop so it contacts
the limb as shown in Figure 2.
OPTION 2: Set Limb Stop to the Longest “A” Postition. Time bow to cable stops at desired
draw length.Set Limb stop to the corresponding stop position. Draw bow with an arrow and
observe whether the cable stop or Limb Stop contacts first. Make small adjustments to the
Limb Stop position and recheck until it contacts at
the same time as the cable stop.
FIGURE 2FIGURE 1
8-32 Button Head Screw
PAGE
18
Compound Bow
USER’S GUIDE
Setting ProPhecy Bow
MadneSS xP MoMentuM
A30 30 31
B29-1/2 29-1/2 30-1/2
C29 29 30
D28-1/2 28-1/2 29-1/2
E28 28 29
F27-1/2 27-1/2 28-1/2
G27 27 28
H26-1/2 26-1/2 27-1/2
I26 26 27
J25-1/2 25-1/2 26-1/2
K25 25 26
SETTING DREAM
SEASON DNA DNA SP SOURCE PREMONITION VERGE
& STILETTO FREAK SP DRIVE LT
A 30 30 31-1/2 30 27 33 31
B 29-1/2 29-1/2 31 29-1/2 26-1/2 32-1/2 30-1/2
C 29 29 30-1/2 29 26 32 30
D 28-1/2 28-1/2 30 28-1/2 25-1/2 31-1/2 29-1/2
E 28 28 29-1/2 28 25-1/8 31 29
F 27-1/2 27-1/2 29 27-1/2 24-5/8 30-1/2 28-1/2
G 27 27 28-1/2 27 24-1/4 30 28
H 26-1/2 26-1/2 28 26-1/2 23-3/4 29-1/2 27-1/2
I 26 26 27-1/2 26 23-3/8 29 27
J - 25-1/2 27 25-1/2 22-7/8 28-1/2 26-1/2
K - 25 26-1/2 25 22-1/2 28 26
L - 24-1/2 26 24-1/2 22 27-1/2 25-1/2
SETTING DOMINATOR
MAX
DOMINATOR
3D MAX SUPRA MAX PHENOM PHENOM SD
A 31-1/2 30-1/2 30 30 28-1/2
B 31 30 29-1/2 29-1/2 28
C 30-1/2 29-1/2 29 29 27-1/2
D 30 29 28-1/2 28-1/2 27
E 29-1/2 28-1/2 28 28 26-1/2
F 29 28 27-1/2 27-1/2 26
G 28-1/2 27-1/2 27 27 25-1/2
H 28 27 26-1/2 26-1/2 25
I 27-1/2 26-1/2 26 26 24-1/2
J 27 26 25-1/2 25-1/2 24
K - - - - 23-1/2
L - - - - 23
PSE PRO SERIES BOWS: DRAW SETTING CHART
NOTE: The PSE Full Throttle™ has cam-specific draw lengths from 26-1/2” to 30” in 1/2” increments. PSE MAIN LINE BOWS: DRAW SETTING CHART
PSE Mainline bows with highly adjustable cams continued on page 20
Compound Bow
USER’S GUIDE
PAGE
19
Setting ProPhecy Bow
MadneSS xP MoMentuM
A30 30 31
B29-1/2 29-1/2 30-1/2
C29 29 30
D28-1/2 28-1/2 29-1/2
E28 28 29
F27-1/2 27-1/2 28-1/2
G27 27 28
H26-1/2 26-1/2 27-1/2
I26 26 27
J25-1/2 25-1/2 26-1/2
K25 25 26
SETTING DOMINATOR
MAX
DOMINATOR
3D MAX SUPRA MAX PHENOM PHENOM SD
A 31-1/2 30-1/2 30 30 28-1/2
B 31 30 29-1/2 29-1/2 28
C 30-1/2 29-1/2 29 29 27-1/2
D 30 29 28-1/2 28-1/2 27
E 29-1/2 28-1/2 28 28 26-1/2
F 29 28 27-1/2 27-1/2 26
G 28-1/2 27-1/2 27 27 25-1/2
H 28 27 26-1/2 26-1/2 25
I 27-1/2 26-1/2 26 26 24-1/2
J 27 26 25-1/2 25-1/2 24
K - - - - 23-1/2
L - - - - 23
PSE MAIN LINE BOWS: DRAW SETTING CHART
PSE Mainline bows with highly adjustable cams continued on page 20
PAGE
20
Compound Bow
USER’S GUIDE
PSE HIGHLY ADJUSTABLE
CAM INFORMATION
The following pages of information apply to the
following PSE Main Line models:
• PSE SURGE™
• PSE FEVER™ ONE
• PSE VISION™
• PSE FEVER™
• PSE MINI BURNER™ XT
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
