Trans-Dapt Performance 65396539 Operating instructions

Brand
Trans-Dapt Performance
Model
65396539
Type
Operating instructions

This manual is also suitable for

Trans-Dapt Performance 65396539 is a universal transmission crossmember designed to fit in "open channel" frames with a minimum measurement between rails of 26" and a maximum measurement between rails of 36". It is compatible with TH350/TH400 transmissions and has no drop distance. This crossmember can be mounted to the inside or outside of the frame rails and features a rubber pad for vibration dampening. It includes end caps, 5/8" bolts, nuts, and lockwashers for easy installation. For added security, it is recommended to tack weld the crossmember to the end caps.

Trans-Dapt Performance 65396539 is a universal transmission crossmember designed to fit in "open channel" frames with a minimum measurement between rails of 26" and a maximum measurement between rails of 36". It is compatible with TH350/TH400 transmissions and has no drop distance. This crossmember can be mounted to the inside or outside of the frame rails and features a rubber pad for vibration dampening. It includes end caps, 5/8" bolts, nuts, and lockwashers for easy installation. For added security, it is recommended to tack weld the crossmember to the end caps.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Determine the correct location to mount the crossmember.
Measure the distance between the frame rail mounting points and the crossmember tube. Calculate how much of the crossmember must be trimmed.
Divide this length by 2, and remove that much from each side of the main crossmember tube. Keep in mind that the end cap plates are 3/16” thick. This
crossmember may be mounted to the inside or outside of the frame rails
Install the end caps onto the crossmember and test fit, ensuring the crossmember is square with frame. (Re-trim center tube if necessary)
With the crossmember and end caps in position and square, precisely mark the position of the crossmember holes on the frame rails. Set the
crossmember and end caps aside.
Drill the mounting holes in frame rails with a 13/32” (or Y) drill bit.
Install the transmission mount pad onto the transmission.
Apply a small amount of threadlocker to the supplied 5/8” bolts, and fasten the crossmember with end caps to the frame rails using the nuts and
lockwashers also supplied with the crossmember.
Connect the crossmember to the transmission by installing a hex bolt with threadlocker through the crossmember flange and into the transmission pad.
For the most secure installation, it is recommended that the crossmember be tack welded to the end caps.
The unit can now be removed and a full weld bead run between the end caps and crossmember before applying paint or powder coating.
(See Figure B)
(optional)
*
*
4558 4548 4538 TH350/TH400 No Drop
4559 TH350/TH400
9444 9474 9424 TH350/TH400 6”
6538 6548 6558 700R4, 4L60E & T56 No Drop
6559 6549 6539 700R4, 4L60E & T56 3”
6544 6534 6524 700R4, 4L60E & T56 6”
6521 6522 4538 FORD C4, C6 No Drop
6523 6525 4539 FORD C4, C6 3”
6526 6527 9424 FORD C4, C6 6”
4549 4539 3”
Univ-transcrossmember-install
tel:(562) 921-0404 website:www.tdperformance.com email:[email protected]
Design varies by part number.
CROSSMEMBER
ONLY
(No Pads)
TRANSMISSION
CROSSMEMBER
PAD
with
POLYURETHANE
CROSSMEMBER
PAD
with
RUBBER
CROSSMEMBER
DROP DISTANCE
UNIVERSAL TRANSMISSION CROSSMEMBERS
INSTALLATION INSTRUCTIONS
DESIGNED TO FIT IN “OPEN CHANNEL” FRAMES. MINIMUM MEASUREMENT BETWEEN RAILS IS 26”, MAXIMUM MEASUREMENT BETWEEN RAILS IS 36”.
*If crossmember will be removed for finishing, do not apply threadlocker until final installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Determine the correct location to mount the crossmember.
Measure the distance between the frame rail mounting points and the crossmember tube. Calculate how much of the crossmember must be trimmed.
Divide this length by 2, and remove that much from each side of the main crossmember tube. Keep in mind that the end cap plates are 3/16” thick. This
crossmember may be mounted to the inside or outside of the frame rails
Install the end caps onto the crossmember and test fit, ensuring the crossmember is square with frame. (Re-trim center tube if necessary)
With the crossmember and end caps in position and square, precisely mark the position of the crossmember holes on the frame rails. Set the
crossmember and end caps aside.
Drill the mounting holes in frame rails with a 13/32” (or Y) drill bit.
Install the transmission mount pad onto the transmission.
Apply a small amount of threadlocker to the supplied 5/8” bolts, and fasten the crossmember with end caps to the frame rails using the nuts and
lockwashers also supplied with the crossmember.
Connect the crossmember to the transmission by installing a hex bolt with threadlocker through the crossmember flange and into the transmission pad.
For the most secure installation, it is recommended that the crossmember be tack welded to the end caps.
The unit can now be removed and a full weld bead run between the end caps and crossmember before applying paint or powder coating.
(See Figure B)
(optional)
*
*
4558 4548 4538 TH350/TH400 No Drop
4559 TH350/TH400
9444 9474 9424 TH350/TH400 6”
6538 6548 6558 700R4, 4L60E & T56 No Drop
6559 6549 6539 700R4, 4L60E & T56 3”
6544 6534 6524 700R4, 4L60E & T56 6”
6521 6522 4538 FORD C4, C6 No Drop
6523 6525 4539 FORD C4, C6 3”
6526 6527 9424 FORD C4, C6 6”
4549 4539 3”
Univ-transcrossmember-install
tel:(562) 921-0404 website:www.tdperformance.com email:[email protected]
Design varies by part number.
CROSSMEMBER
ONLY
(No Pads)
TRANSMISSION
CROSSMEMBER
PAD
with
POLYURETHANE
CROSSMEMBER
PAD
with
RUBBER
CROSSMEMBER
DROP DISTANCE
UNIVERSAL TRANSMISSION CROSSMEMBERS
INSTALLATION INSTRUCTIONS
DESIGNED TO FIT IN “OPEN CHANNEL” FRAMES. MINIMUM MEASUREMENT BETWEEN RAILS IS 26”, MAXIMUM MEASUREMENT BETWEEN RAILS IS 36”.
*If crossmember will be removed for finishing, do not apply threadlocker until final installation.
  • Page 1 1

Trans-Dapt Performance 65396539 Operating instructions

Brand
Trans-Dapt Performance
Model
65396539
Type
Operating instructions
This manual is also suitable for

Trans-Dapt Performance 65396539 is a universal transmission crossmember designed to fit in "open channel" frames with a minimum measurement between rails of 26" and a maximum measurement between rails of 36". It is compatible with TH350/TH400 transmissions and has no drop distance. This crossmember can be mounted to the inside or outside of the frame rails and features a rubber pad for vibration dampening. It includes end caps, 5/8" bolts, nuts, and lockwashers for easy installation. For added security, it is recommended to tack weld the crossmember to the end caps.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents